ELECTRIC FAN HEATERS Devil 6003, 6005, 6009 & 6015 Part Nos: 6925220, 6925225, 6925230 & 6925235 OPERATING & MAINTENANCE INSTRUCTIONS GC0110
INTRODUCTION Thank you for purchasing this CLARKE Electric Fan Heater. Please read this manual thoroughly and follow the instructions carefully. Before attempting to use the heater, thoroughly familiarise yourself with the heater & its operation. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to the heater giving you long and satisfactory service.
TABLE OF CONTENTS INTRODUCTION .................................................................................. 2 GUARANTEE ........................................................................................ 2 ENVIRONMENTAL PROTECTION ......................................................... 2 TABLE OF CONTENTS .......................................................................... 3 GENERAL SAFETY RULES .....................................................................
GENERAL SAFETY RULES 1) WORK AREA 1. These heaters are for INDOOR USE ONLY. 2. Do not expose the heater or power cable to rain or wet conditions. Any water entering the heater will increase the risk of electric shock. DO NOT use this heater in a bathroom, shower room, in the vicinity of a swimming pool, or any wet environment. 3. NEVER locate the heater near combustible materials such as curtains, furniture etc. Allow at least 1 metre clearance. 4.
3. Keep the mains cable well away from machines and ensure an adequate electrical supply is close at hand so that the operation is not restricted by the length of the cable. 4. ALWAYS disconnect from the mains supply before moving the heater or performing any maintenance tasks. 5. ALWAYS use ONLY in an upright position. 6. Inspect the mains cable regularly for signs of damage. DO NOT use if it is damaged, and ALWAYS keep it away from the source of heat. 7. Check the fan heater for damage before use.
ELECTRICAL CONNECTIONS DEVIL 6003 (3KW) HEATER UNIT This model is provided with a 13 amp BS 1363 plug, fitted with a 13amp fuse and MUST be connected to a standard, 230 Volt (50Hz) electrical supply, preferably through an approved plug, or a suitably fused isolator switch.
DEVIL 6005 (5KW), DEVIL 6009(9KW) AND DEVIL 6015(15KW) UNITS These machines MUST be connected to a 400 Volt, 3 PHASE 50Hz supply through a suitably fused isolator switch. It cannot be operated from a single phase supply. The user should purchase a suitable connecting lead as shown in the diagram, which is compatible with the appliance socket.
OPERATION The Devil range of fan assisted electric heaters are suitable for household (Devil 6003 only) or workshop/factory use. They incorporate a thermostat which detects the temperature of the room air and controls the heater to maintain a pre-selected temperature between 0 & 40°C. A manually reset thermal cutout is provided for safety in the event of overheating on the 6005, 6009 & 6015 models.
When using the heater for the first time a slight emission of smoke may be noticed. This is quite normal and soon stops. It is caused by residual traces of oil remaining on the element from production. After use, turn the thermostat to the OFF position and turn the selector switch to the Fan Only position, and leave the unit to cool down for a couple of minutes. 5KW, 9KW &15KW HEATERS The 5 & 9kw units have a three position twist control for FAN only, and FAN plus either half or full heat output.
MAINTENANCE If the heater has been used, ALWAYS allow it to cool down for at least 10 minutes (by switching the heater OFF, but leave the fan running), then disconnect from the mains supply before performing any maintenance tasks. PERIODICALLY • Disconnect from the mains supply, and use compressed air to clean out the unit. ALWAYS wear a dust mask to perform this operation. • If there is any serious build up of dirt, wipe thoroughly with a damp cloth. Take care that no moisture enters the heater.
FAULT FINDING Problem Possible cause Plug is loose/bad connection. Heater does not operate, although plugged in with the Fuse blown switch and ther mostat switched on. The unit failed to heat up so only the air fan operated. Pull the plug out & check the connection of the plug and socket. Replace if necessary and investigate cause. If fuse b l o w s re p e a t e d l y , c o n s u l t your CLARKE dealer. No power at socket outlet. Heating element glowing hot.
PARTS DIAGRAM DEVIL 6003 NO CODE DESCRIPTION Qty NO CODE DESCRIPTION Qty 1 N/A Support Leg 2 13 C X D E V 600305 Front Grille 1 2 N/A Top Panel 1 14 C X D E V 600306 Fan Control Knob 1 3 N/A Chassis panel 1 15 N/A Front Panel 1 4 C X D E V 600301 F an 1 16 N/A Mounting Packer 2 5 C X D E V 600302 Motor 1 17 N/A Washer 1 6 N/A Retaining clips 2 18 C X D E V 600307 Power/Fan Speed Controller 1 7 N/A Rear Panel 1 19 C X D E V 600308 Temperature Con
PARTS DIAGRAM DEVIL 6005 NO CODE DESCRIPTION Qty NO CODE DESCRIPTION Qty 1 N/A Support Leg 2 13 C X D E V 600504 Front Grille 1 2 N/A Top Panel 1 14 C X D E V 600505 Fan Control Knob 1 3 N/A Chassis panel 1 15 N/A Front Panel 1 4 C X D E V 600501 F an 1 16 N/A Plastic Plug 1 5 C X D E V 600502 Motor 1 17 N/A Support Bar 1 1 6 N/A 5-Pin Socket 1 18 C X D E V 600506 Power/Fan Speed Controller 7 N/A Rear Panel 1 19 C X D E V 600507 Temperature Contr
PARTS DIAGRAM DEVIL 6009 NO CODE DESCRIPTION Qty NO CODE DESCRIPTION Qty 1 N/A Support Leg 2 12 C X D E V 600903 Heating Element 2 2 N/A Top Panel 1 13 C X D E V 600904 Front Grille 1 3 N/A Chassis Panel 1 14 C X D E V 600905 Control Knob 2 4 C X D E V 600901 F an 1 15 N/A Front Panel 1 5 C X D E V 600902 Motor 1 16 N/A Support Bar 1 6 N/A Cable Entry 2 17 N/A Closing Panel 1 7 N/A Rear Panel 1 18 C X D E V 600907 Power/Fan Speed Controller 1
PARTS DIAGRAM DEVIL 6015 NO CODE DESCRIPTION Qty NO CODE DESCRIPTION Qty 1 N/A Support Leg 2 13 C X D E V 601504 Front Grille 1 2 N/A Top Panel 1 14 C X D E V 601505 Fan Control Knob 1 3 N/A Chassis panel 1 15 N/A Front Panel 1 4 C X D E V 601501 F an 1 16 N/A Heat Shield 2 5 C X D E V 601502 Motor 1 17 N/A Fan Closing Plate 1 6 N/A Angle Bracket 1 18 C X D E V 601506 Power / Fan Speed Controller 1 7 N/A Rear Panel 1 19 C X D E V 601507 Temperat
WIRING DIAGRAMS 230v / 3kw T = Thermostat M = Motor D = Heater Tube K1, K2 = Switch TV = Self resetting themal cut-out 400v / 5kw 400v / 9kw T = Thermostat B = Switch M = Motor TV =Manually resetting thermal cut-out D = Heater Tube 16
WIRING DIAGRAMS 400v / 15kw T = Thermostat B = Switch M = Motor TV=Manually resetting thermal cut-out D =Heater Tube 17
TECHNICAL SPECIFICATION Item Published Specification Model Devil 6003 Devil 6005 Devil 6009 Devil 6015 Part No 6925220 6925225 6925230 6925235 Weight 5.5kg 7.0kg 9.0kg 14.4kg 295 x 305 x 425 350 x 335 x 465 400 x 345 x 535 Input Wattage(kw) 1.5 (setting 1) 3.0 (setting 2) 2.5 (setting 1) 5.0 (setting 2) 4.5 (setting 1) 9.0 (setting 2) 95w (fan only) 5kw (setting 1) 10kw (setting 2) 15kw (setting 3) Input Amperage 6.39 (setting 1) 12 (setting 2) 7.2 13 21.
DECLARATION OF CONFORMITY DECLARATION OF CONFORMITY This is an important document and should be retained.
