DEVIL QUARTZ INFRA-RED HALOGEN HEATERS Devil 370P, 370SP, 371P & 371SP Part Nos: 6926000, 6926005, 6926010 & 6926015 OPERATING & MAINTENANCE INSTRUCTIONS GC0210
INTRODUCTION Thank you for purchasing this CLARKE Quartz Halogen Infra-red Heater. Please read this manual thoroughly and follow the instructions carefully. Before attempting to use the heater, thoroughly familiarise yourself with the heater & its operation. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to the heater giving you long and satisfactory service.
GENERAL SAFETY RULES 1) WORK AREA 1. These heaters are for INDOOR USE ONLY. 2. Do not expose the heater or power cable to rain or wet conditions. Any water entering the heater will increase the risk of electric shock. DO NOT use this heater in a bathroom, shower room or any other wet environment. 3. NEVER locate the heater near combustible materials such as curtains, furniture etc. Allow at least 1 metre distance. 4. DO NOT locate the heater close to an adjacent wall or low ceiling.
. ALWAYS disconnect from the mains supply before moving the heater, or performing any cleaning or maintenance tasks. 5. Inspect the mains cable regularly for signs of damage. DO NOT use if it is damaged, and ALWAYS keep it away from the source of heat. 6. Check the heater for damage before use. DO NOT use if the heater tubes are damaged or broken. Any damage should be properly repaired or the part replaced. If in doubt, DO NOT use. Consult your local Clarke dealer. 3) SERVICE & REPAIRS 1.
If this appliance is found to be fitted with a plug which is moulded on to the electric cable (i.e. non-rewireable) please note: 1. The plug must be thrown away if it is cut from the electric cable. There is a danger of electric shock if it is subsequently inserted into a socket outlet. 2. Never use the plug without the fuse cover fitted. 3. Should you wish to replace a detachable fuse carrier, ensure that the correct replacement is used (as indicated by marking or colour code). 4.
UNPACKING AND ASSEMBLY Before assembling, please check contents against the following list and advise your dealer immediately if any parts are missing. 1 x Heater 2 x Halogen Lamps 1 x Frame (SP only) 2 x Saddle Supports (SP only) 1 x Fixings pack 4 x Castors (2 with brakes) 2 x Support Legs (P only) 2 x Securing Knobs (SP only) 2 x Handles (P only)/1 x Handle (SP only) TOOLS REQUIRED 7mm, 13mm and 14mm spanners, pozidrive (phillips) screwdriver DEVIL 370 /371P 1.
OPERATION 1. Position the heater where required, and lock the castors to prevent the heater from rolling. 2. Slacken the locking knobs and rotate the heater body to the required angle. Tighten the securing knobs on each side to lock into place (SP models only). 3. Connect the mains cable to a suitable power supply. 4. Use the on/off switches to turn on either one, or both heating elements.
1. Loosen and remove the two pozidrive screws securing the wire guard, remove the guard and store removed parts safely. 2. To remove lamp, grasp lamp and gently but firmly push it to one end of the heater. The lamp holders are spring loaded and will allow the lamp sufficient movement to clear the opposite holder. 3. Remove the lamp and dispose of, according to local regulations. 4. Fit new halogen lamp in reverse order, repeat procedure for second tube. 5. Replace the guard using the screws removed earlier.
COMPONENT PARTS No Description Devil 370 Devil 371 1 Castor (standard) WGDEV37001 WGDEV37101 2 Castor with Brake WGDEV37002 WGDEV37102 3 Ceramic End Cap WGDEV37003 WGDEV37103 4 Quartz Halogen Tube WGDEV37004 WGDEV37104 5 ON/OFF Switch WGDEV37005 WGDEV37105 6 Power Cable WGDEV37006 WGDEV37106 7 Wire Guard WGDEV37007 WGDEV37107 8 Frame (SP only) WGDEV37008 WGDEV37108 9 Plastic Handle WGDEV37009 WGDEV37109 10 Securing Knob (SP only) WGDEV37010 WGDEV37110 11 Plastic Sa
TECHNICAL SPECIFICATION Model Devil 370P Devil 370SP Devil 371P Devil 371SP Part No 6926000 69256005 6926010 6926015 Weight 16.6 kg 15.1 kg 16.6 kg 15.1 kg 570x510x620 490x570x890 570x510x620 Dimensions (LxWxH) mm 490x570x890 Wattage 3 KW 3 KW 3 KW 3 KW Amperage 12.5 A 12.5 A 27.27 A 27.27 A Supply Voltage 230v / 50 Hz 230v / 50 Hz 110v / 50 Hz 110v / 50 Hz Fuse rating 13 A 13 A 32A 32A Insulation Class IP20 IP20 IP20 IP20 Max.
DECLARATION OF CONFORMITY 11
