DEVIL QUARTZ HALOGEN HEATER MODEL NO: DEVIL 370PD PART NO: 6920257 OPERATING & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS GC08/22
INTRODUCTION Thank you for purchasing this CLARKE Quartz Halogen Heater. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. SPECIFICATIONS Model Number Devil 370PD Part Number 6920257 Weight 16kg Dimensions (W x D x H) 560 x 490 x 870 mm Rated Input Wattage 2.8 kW (2 x 1.
THE FOLLOWING TABLE ADDRESSES THE INFORMATION REQUIREMENTS OF REG.2015/1188 Item Symbol Value Unit Heat output Measured seasonal space heating energy efficiency 35% Nominal heat output Pnom 2.8 kW Minimum heat output (indicative) P min 1.4 kW Maximum continuous heat output P max 2.8 kW At nominal heat output elmax n/a kW At minimum heat output el min n/a kW In standby mode elSB 0.
GENERAL SAFETY RULES 1. These heaters are for INDOOR USE only. 2. DO NOT expose the heater or power cable to rain or wet conditions. Any water entering the heater will increase the risk of electric shock. DO NOT use this heater in a bathroom, shower room or any other wet environment. 3. NEVER locate the heater near combustible materials such as curtains, furniture etc. Allow at least 1 metre distance. 4. DO NOT locate the heater close to an adjacent wall or low ceiling.
3. DO NOT abuse the electrical cable. Never use the cable for pulling or unplugging the heater. Keep the cable away from sources of heat, oil, sharp edges or moving parts. Damaged or tangled cables increase the risk of electric shock. 4. Keep the power cable well away from machines and ensure an adequate electrical supply is close at hand so that the operation is not restricted by the length of the cable. 5.
ELECTRICAL CONNECTIONS WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE POWER SUPPLY. The 230v models are provided with a 13 amp BS 1363 plug, fitted with a 13 amp fuse and MUST be connected to a standard, 230 Volt (50Hz) electrical supply, preferably through a suitably fused isolator switch.
UNPACKING AND ASSEMBLY UNPACKING Before assembling, please check contents against the following list and advise your dealer immediately if any parts are missing. 1 x Heater 2 x Support frames with castors (2 with brakes) 1 x Handle 1 x Fixings pack 1 x Remote control unit ASSEMBLY 1. Attach the supporting frames to the heater body using 14 mm securing bolts supplied. • The braked castors should be at the rear of the heater 2.
OPERATION WARNING: FOR SAFE OPERATION OF THIS HEATER IT IS ESSENTIAL TO READ THESE INSTRUCTIONS BEFORE USE. WARNING: PLEASE NOTE THAT THE HEATING ELEMENTS OF THIS PRODUCT DO NOT GLOW WHILST IN OPERATION. ANY PICTURES SHOWING THIS IN ADVERTISING MATERIAL ARE FOR ILLUSTRATION ONLY. USING THE REMOTE CONTROL All operations must be done using the remote control. • 2 x AAA batteries are required and are installed as shown by the diagram found inside the control unit.
3. Press to turn on the upper heating lamp and the screen will show P1. 4. Press to select the mode from P1-P6, referring to the different temperature settings. P1 Only the upper element is working P2 24o P3 26o P4 28o P5 30o P6 Both elements are working • During mode P2-P5 the upper element is working all the time and the lower element will be turned off automatically according to the set temperature. 5. The user can change from mode P1 and P6 by pressing .
SETTING THE SHUTDOWN TIMER 1. Press to set the shutdown timer. The time on the screen flickers with initial status 00:00. 2. Press and to set the time to turn the heater off. • It increases/decreases 1 hour per press. 3. Press when you finish setting and the heater will be in the countdown mode. • It will shut down 2 hours later. 4. When the time is up, the heater turns off automatically and enters the standby state P0. FUNCTION FOR DETECTING OPENING WINDOWS 1.
CLEANING & MAINTENANCE If the heater has been used, always allow it to cool down for at least 15 minutes and disconnect from the power supply before performing any maintenance tasks. FITTING/ REPLACING TUBES Before attempting to fit/replace halogen tubes, make sure that the heater is switched off and isolated from the electrical supply by removing the plug from the socket. NEVER handle the halogen tubes with bare hands.
FAULT FINDING SYMPTOM Heater does not operate, although plugged in and switched on. Heater tube is glowing hot. Heater does not respond to remote controller. PROBLEM SOLUTION Plug is loose/bad connection. Remove the plug & check the connection of the plug and socket. Fuse blown. Replace if necessary and investigate the cause. If fuse blows repeatedly, consult your CLARKE dealer. No power at socket outlet. Insert plug into a suitable socket. Tilt safety switch is disabling unit.
PARTS DIAGRAM No Description No Description 1 Castor (standard) 9 Bolt 2 Castor with Brake 10 Support frame 3 Ceramic end cap 11 Control panel module 4 Halogen tube 12 Circuit-board (not shown) 5 Wire guard 13 Tilt safety switch (not shown) 6 Power cable 14 On/off power switch (not shown) 7 Handle 15 Remote control unit 8 Plastic spacers 13 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
DECLARATION OF CONFORMITY-UK 14 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
DECLARATION OF CONFORMITY-CE 15 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
