VARIABLE SPEED JIG SAW 800W JIGSAW WITH LASER Part No. 6460200 MODEL No. CON800 Part No.
Thank you for purchasing this CLARKE 800W Jigsaw with Laser. Before attempting to use the Jigsaw, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to the Jigsaw giving you long and satisfactory service. GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase.
GENERAL SAFETY PRECAUTIONS WARNING: As with all machinery, there are certain hazards involved with their operation and use. Exercising respect and caution will considerably lessen the risk of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator or damage to property, may result. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. ALWAYS Learn the machines’ applications, limitations and the specific potential hazards peculiar to it.
GENERAL SAFETY PRECAUTIONS 16. 17. 18. 19. 20. ALWAYS remove plug from electrical outlet when adjusting, changing parts, or working on the machine. NEVER operate machine while under the influence of drugs, alcohol or medication. NEVER leave machine running unattended. Turn power off. Do not leave the machine until it comes to a complete stop. NEVER force the machine. It will do a better and safer job at the rate for which it was designed.
ELECTRICAL CONNECTIONS This product is provided with a standard 13 amp, 230 volt (50Hz), BS 1363 plug, for connection to a standard, domestic electrical supply. Should the plug need changing at any time, ensure that a plug of identical specification is used.
BEFORE USE FITTING THE JIGSAW BLADE WARNING! Before removing, or installing a jigsaw blade, make sure that the mains plug has been removed from the mains supply. 1. 2. 3. Loosen the two blade securing screws, using the hexagonal key provided. With the blade teeth facing forwards, push the blade shank into the blade locating clip as far as possible. Slightly tighten the two blade securing screws alternately, to position the blade. Blade securing screws Blade locating clip Fig 1 4.
BEFORE USE ADJUSTING THE CUTTING ANGLE WARNING! Before adjusting the cutting angle, make sure that the mains plug has been removed from the mains supply. 1. Loosen the base plate screws using the hexagonal key provided. See Fig 3 2. Tilt the base to the required angle. 3. There is a calibration plate on the base plate to assist you in selecting the correct angle. See Fig 4. 4. Base plate screws Fig 3 Re-tighten the base plate screws to secure the base plate.
OPERATING PENDULUM ACTION When the pendulum action is selected, the blade achieves maximum penetration on the upward cutting stroke and is lifted back, away from the material, on the downward non-cutting stroke. This gives improved quality of cut, and longer blade life. To set the pendulum action, rotate the pendulum action switch to the desired setting. The table below can be used to select the correct settings.
OPERATION ON/OFF SWITCH Fig 8 1. Squeeze the trigger switch. The jigsaw will run at the level selected with the variable speed selector. 2. To switch off the jigsaw, release the trigger switch. When the blade has stopped remove it from the workpiece Trigger switch WARNING! The blade will continue to run for a short period after the trigger has been release. Wait until it stops before removing it from the workpiece. For continuous operation, Fig 9 1. Squeeze and hold the trigger switch. 2.
OPERATION JIGSAW TIPS • Ensure your cutting line is free from nails before you start cutting. • If you are not making a cut all the way through the workpiece, allow the blade to come to a complete stop before removing it from the workpiece Wood • Use a pencil to draw a cutting line on the wood. • Select the correct speed and pendulum setting for the wood being cut. • Allow the jigsaw to reach full speed before applying it to the wood. Metal • Use blades designed for cutting metal.
MAINTENANCE WARNING! Before performing any maintenance tasks make sure that the mains plug has been removed from the mains supply. • After use, clean all dust and wood chippings from the jigsaw. • Clean all of the ventilation slots on the motor housing. • Make sure that the base plate is free from dirt and grease. • The blade locating clip and support roller should be kept clean and lightly oiled at regular intervals. • Keep the handle clean and free from oil and grease.
PARTS DIAGRAM 13
PARTS LIST Item Part Number Description Qty Available as a Spare part Item Part Number Description Qty Available as a Spare part 1 KP500200 Tapping Screw 7 No 28 KP100040 Rotor 1 No 2 KP300037 Left Enclosure 1 No 29 KP314500 Brush Holder 2 Yes 3 KP501507 Adjusting Screw 2 No 30 KP162400 Carbon Brush 2 Yes 4 KP224339 Connecting Plate 1 No 31 KP222800 Brush Bushing 2 No 5 KP145002 Base Plate 1 No 32 KP520012 Bearing 1 No Yes 6 KP204003 Metal Pendulum
DECLARATION OF CONFORMITY DECLARATION OF CONFORMITY We declare that this product complies to the following standards/directives: 98/37/EC Product Description: Jigsaw Model No: CON800 Date 09 - August - 2007 Signed: Engineering Manager When disposing of this product, ensure it is disposed of according to all local ordinances. It must not be disposed of with general household waste.
