HOT AIR GUN MODEL NO: CHG2000B PART NO: 3400755 USER INSTRUCTIONS GC0314
INTRODUCTION Thank you for purchasing this CLARKE Hot Air Gun. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase.
6. KEEP other persons away. Do not let persons, especially children, not involved in the work, touch the tool or extension cable and keep them away from the work area. 7. NEVER operate a power tool when under the influence of alcohol, drugs or medication. 8. Do not use power tools in the presence of flammable liquids or gasses. 9. Stay alert, watch what you are doing, use common sense and do not operate the power tool when you are tired. CARE OF POWER TOOLS 1. Read this manual carefully.
13. Avoid accidental starting by making sure the power switch is off before plugging in the power cable. ADDITIONAL SAFETY RULES FOR HOT AIR GUNS CAUTION: WITH ALL MACHINES, THERE ARE CERTAIN HAZARDS INVOLVED WITH THEIR OPERATION AND USE. EXERCISING RESPECT AND CAUTION WILL CONSIDERABLY LESSEN THE RISK OF PERSONAL INJURY. HOWEVER, IF NORMAL SAFETY PRECAUTIONS ARE OVERLOOKED, OR IGNORED, PERSONAL INJURY TO THE OPERATOR, OR DAMAGE TO PROPERTY MAY RESULT. 1.
ELECTRICAL CONNECTIONS WARNING! Read these electrical safety instructions thoroughly before connecting the product to the mains supply. Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. Connecting it to any other power source may cause damage. This product may be fitted with a non-rewireable plug.
PRODUCT OVERVIEW 1 5 2 3 6 NO DESCRIPTION 4 7 NO 8 DESCRIPTION 1 Reflector Nozzle 5 Glass Protection Nozzle 2 Concentrator Nozzle 6 Defuser Nozzle 3 Triangular Shavehook (scraper) 7 Moulded Plastic Carry Case 4 Hot Air Gun 8 Handle for Triangular Shave Hook INVENTORY CHECK Before starting work, please check contents against the list above and advise your dealer immediately if any parts are missing. 6 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.
OPERATION Before starting work it is recommended that you heat a test piece to ensure you have the correct heat setting. In addition you should always take steps to protect sensitive or delicate areas where the effect of heat could cause damage (i.e. glass and plastics). Do not apply heat to the same place for a long time. After the work has been completed, switch the gun OFF, disconnect from the mains supply and allow to cool in a safe place.
REMOVING PAINT FROM WINDOW FRAMES DO NOT point the gun directly at glass and always ensure it is adequately protected. A glass protection nozzle is provided for use when stripping window frames etc. 1. Fit the glass protection nozzle to the front of the hot air gun and angle it so that the gun can be placed up against the window, with the cowl of the nozzle, flat against the glass as shown. 2. It will be necessary to change the position of the protection nozzle as you work around the window pane.
2. Heat the sleeve evenly. DE-FREEZING WATER PIPES Fit the reflector nozzle to the front of the hot air gun. 1. Always heat frozen areas inwards from the edge to the centre. 2. Take special care when defrosting plastic pipes. 3. Provide protection against heat damage to nearby paint and wall coverings where necessary. 4. Be aware that copper gas pipes can be difficult to distinguish from copper water pipes. Always check first. 5.
SPARES & ACCESSORIES ITEM DESCRIPTION PART NUMBER 1 Air Nozzle Cover HT2000B01 2 Concentrator Nozzle HT2000B02 3 Diffuser Nozzle HT2000B03 4 Glass Protector Nozzle HT2000B04 5 Reflector for Nozzle HT2000B05 6 Triangular Shave Hook HT2000B06 7 Triangular Shave Hook Handle HT2000B07 SPECIFICATION Model Number CHG2000B Dimensions (D x W x H) 244 x 74 x 255 mm Product Weight 0.
DECLARATION OF CONFORMITY 11 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.
