245 MM (10) BANDSAW & STAND MODEL No. CBS250 Part Part No. No.
Please read these instructions carefully before operating the tool CLARKE bandsaw. Before using the device, please read this manual thoroughly and carefully follow all instructions given. This is for your own safety and that of others around you, and is also to help you achieve a long and trouble free service from your new tool. Thank you for purchasing this CLARKE GUARANTEE This CLARKE product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase.
NOTES CONTENTS Guarantee ............................................................................. 1 Specifications ........................................................................ 2 Safety Precautions ............................................................. 3-4 Electrical Connections ......................................................... 5 Unpacking The Machine ..................................................... 6 Assembly ............................................................
SAFETY PRECAUTIONS Parts List Item 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 Part No QD250081 QD250082 QD250083 QD250084 QD250085 QD250086 QD250087 QD250088 QD250089 QD250090 QD250091 QD250092 QD250093 QD250094 QD250095 QD250096 QD250097 QD250098 QD250099 QD250100 QD250101 QD250102 QD250103 QD250104 QD250105 QD250106 QD250107 QD250108 QD250109 Description Housing Upper Slide Board Guide Lever Rack Cross Pan Hd Screw Cover Board Shaft Roll Pin Guid
14. ALWAYS wear proper apparel. loose clothing or jewellery may get caught in moving parts. wear protective hair covering to contain long hair. 15. ALWAYS use recommended accessories. the use of improper accessories could be hazardous. 16. ALWAYS remove plug from electrical outlet when adjusting, changing parts, or working on the machine. NEVER operate machine while under the influence of drugs, alcohol or any medication. 18. NEVER 17. leave machine running unattended. turn power off.
Parts List Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 ELECTRICAL CONNECTIONS Part No QD250001 QD250002 QD250003 QD250004 QD250005 QD250006 QD250007 QD250008 QD250009 QD250010 QD250011 QD250012 QD250013 QD250014 QD250015 QD250016 QD250017 QD250018 QD250019 QD250020 QD250021 QD250022 QD250023 QD250024 QD250025 QD250026 QD250027 QD250028 QD250029 QD250030 QD250031 QD250032 QD250033 QD250034 QD250035 QD250036 QD250037 QD250038 QD250039
UNPACKING THE MACHINE When lifting etc, always seek assistance from an able bodied person wherever possible, also when seeking assistance, you must ensure that you explain carefully where and when to lift, the weight, where it is going to be placed etc, it is important you that you take complete charge and give clear and precise instructions. Lift only when the person you have asked, that he/she acknowledges full understanding. Parts Diagram To unpack the machine, proceed as follows:, 1.
Parts Diagram ASSEMBLY Stand Assemble sub assy x 2, see fig. 3. Parts required per assy, 2 legs (L), 1 short beam (H), 1 short cross member (D), and 8 short round head screws nuts and washers. Do not fully tighten until all screws and nuts are loosely fitted, once all screws are fitted, check assy for squareness and tighten nuts, do not overtighten. NOTE: beams and cross members fit inside legs, screws are fitted from the outside with washers and nuts on the inside. 1. 2.
Mitre Cutting Fit the aluminium profile with scale, to the front of the table using four bolts and washers supplied, ensure the cut out in the aluminium carrier is lined up with the T slot in the table. DO NOT overtighten the bolts, the aluminium profile is required to be removed when changing or fitting new sawblades.
Use both hands to feed the workpiece in to the blade. The work must be held flat on the table at all times to prevent binding of the blade. Use a steady even pressure just sufficient to keep the blade cutting. Always use a rip fence or mitre guide where possible to eliminate any sideways slip of the work. This is most important when the table is tilted to an angle. Always plan your work ahead. The tradesmans rule is measure twice, cut once.
it almost touches leaving a gap of no less than 0.5mm. Tighten Changing the Sawblade. Upper Blade Guides the grub screw. Ensure the machine is switched OFF, and isolated from the main electrical supply by removing the plug from the 13amp socket. Loosen grub screw B and move the side guide up to the sawblade, again until it is within 0.5mm. Tighten grub screw. Repeat with the other side guide by loosening grub screw C.
