230MM (9”) ANGLE GRINDER MODEL NO: CAG2350 PART NO: 6470098 OPERATION & MAINTENANCE INSTRUCTIONS LS0111
INTRODUCTION Thank you for purchasing this CLARKE 230mm (9”) Angle Grinder. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase.
GENERAL SAFETY RULES 1) WORK AREA 1. Keep the work area clean and well lit. Cluttered and dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. 3. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. 2) ELECTRICAL SAFETY 1. Power tool plugs must match the outlet. Never modify the plug in any way.
) POWER TOOL USE AND CARE 1. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate which it was designed. 2. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. 3. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing power tools.
. Start up speed. Always allow the angle grinder to run up to full operating speed before applying it to the job. 6. Avoid operator fatigue. Stop the angle grinder at regular intervals for a short break to rest hands and arms. 7. Applying the disc to the workpiece. Never bump the angle grinder disc on the workpiece, or let the disc hit any other objects while grinding. 8. Dust masks. Always wear a dust mask when operating this angle grinder. 9. Do not abuse the mains lead.
DISC SAFETY INSTRUCTIONS 1. Disc speed. Check the speed of the disc before fitting to your angle grinder. Never use a disc with a rpm speed less than the rpm speed of your angle grinder. 2. Inspect the disc before fitting. Never use a disc that is chipped, cracked or damaged. Fragments from a broken or damaged disc can cause serious injury. Make sure that defective discs are destroyed and not used. 3. Handling and mounting discs.
SAFETY SYMBOLS Wear ear protection Wear eye protection Not suitable for wet grinding Read instruction manual before use 7
ELECTRICAL CONNECTIONS WARNING! Read these electrical safety instructions thoroughly before connecting the product to the mains supply. Before switching the product on, make sure that the voltage of your electricity supply is the same as that indicated on the rating plate. This product is designed to operate on 230VAC 50Hz. Connecting it to any other power source may cause damage. This product may be fitted with a non-rewireable plug.
OVERVIEW NO DESCRIPTION NO DESCRIPTION 1 Lock Off Lever 7 Threaded hole (for the side handle) 2 On/Off Trigger Switch 8 Rear Handle 3 Disc Guard 9 Mains Lead 4 Grinding/Cutting Disc 10 Air Vents 5 Direction of Rotation Indicator 11 Side Handle 6 Spindle Lock Button 12 Rear Handle Release 9
BEFORE USE FITTING / ADJUSTING THE DISC GUARD WARNING: MAKE SURE THAT THE ANGLE GRINDER IS SWITCHED OFF AND UNPLUGGED FROM THE MAINS SUPPLY BEFORE FITTING OR REMOVING ANY ACCESSORIES. 1. Slide the disc guard into place as shown. 2. Rotate the disc guard to the required position and secure by tightening the cap head screw using the hexagonal key supplied. WARNING: THE DISC GUARD SHOULD BE FITTED SO THAT IT PROVIDES MAXIMUM PROTECTION TO THE USER WHEN IN THE WORKING POSITION. 3.
FITTING AND REMOVING A DISC WARNING: MAKE SURE THAT THE ANGLE GRINDER IS SWITCHED OFF AND UNPLUGGED FROM THE MAINS SUPPLY BEFORE FITTING OR REMOVING ANY ACCESSORIES. 1. Make sure the disc guard is fitted before you fit any cutting/grinding disc. 2. Press and hold the spindle lock as shown on the right. NOTE: You may need to turn the spindle by hand to fully engage the spindle lock. 3. Use the pin spanner supplied to remove the outer flange. 4.
FITTING THE SIDE HANDLE 1. Fit the side handle by screwing it into one of the 3 threaded holes on the angle grinder. ADJUSTING THE REAR HANDLE The rear handle can be rotated to give a more comfortable grip. 1. Push and hold the rear handle release backwards with one hand. 2. Twist the rear handle in 90 degree steps and release the rear handle release button. The handle will only turn a maximum of 180 degrees.
USING YOUR ANGLE GRINDER WARNING: FRAGMENTS FROM A BROKEN/DETACHED DISC CAN CAUSE SERIOUS INJURY. WARNING: WHEN USING CUTTING DISCS, DO NOT STAND DIRECTLY IN LINE WITH THE ROTATING DISC. WARNING: DO NOT PUT SIDEWAYS PRESSURE ON CUTTING DISCS. WARNING: ENSURE THAT THE WORKING POSITION ADOPTED DOES NOT CAUSE OPERATOR FATIGUE WHICH MAY LEAD TO LOSS OF CONTROL OF THE CUTTING DISC AND IMPACT/SNATCH WITH SURROUNDING OBJECTS/ MATERIALS.
CUTTING TIPS • Do not force the disc through the material. Work with a feed rate that is suited to the material being cut. • Do not subject the cutting disc to sideways pressure. • The direction of the cutting motion is important. Always feed the cutting disc into the work so that it cuts in an upward direction. If you do not do this It can result in the disc climbing out of the cut in an uncontrolled manner and may lead to loss of control or serious injury.
MAINTENANCE CHANGING THE CARBON BRUSHES 1. Remove the screw holding the brush cover in place. 2. Remove the worn brush. 3. Replace with the new brush supplied. 4. Repeat on the other side of the body. • Both brushes must be replaced at the same time CLEANING • To maintain the best possible performance from your angle grinder, it must be kept clean. • To reduce fire hazard, keep the cooling vents free of debris.
SPECIFICATIONS Model Number CAG2350 Rated Voltage (V) 230 V Input Power 2350 W No Load Speed 6000 rpm Disc Diameter 230 mm Disc Bore 22 mm Spindle Thread Size M14 Guaranteed Sound Power (Lwa dB) 110 Vibration Levels 3.82 m/s2 Dimensions (L x W x H) 560 x 310 x 136 mm Weight 5.4 kg PARTS AND SERVICING There are no user serviceable parts in this angle grinder, all servicing and repairs should be carried out by your nearest Clarke dealer.
OVERVIEW 18
PARTS LIST NO DESCRIPTION PART NUMBER NO DESCRIPTION PART NUMBER 1 Outer Flange KPCON260001 33 Rotor KPCON260033 2 Grinding Disk KPCON260002 34 Barrel Head Screw KPCON260034 3 Inner Flange KPCON260003 35 Stator Pressure Plate KPCON260035 4 Hexagon Socket Head Bolts KPCON260004 36 Stator KPCON260036 5 Guard KPCON260005 37 Bearing KPCON260037 6 Guard Screw KPCON260006 38 Bearing Ring KPCON260038 7 Barrel Head Screw KPCON260007 39 Casing KPCON260039 8 Elastic Wa
DECLARATION OF CONFORMITY 17
