Freestanding Solid Surface and Acrylic Bathtubs Solid Surface Acrylic Installation Instructions and Operation Manual Effective August 30, 2013 Installer: This booklet must be given to the product owner.
Owner’s Manual and Installation Guide Thank you for choosing a Clarke Products bath. You have purchased the best-built freestanding solid surface/acrylic bathtubs made in America. We know it will give you many years of pleasure. The instructions in this booklet will provide you with the information you need to install and operate this unit. This information is also available online at www.clarkeproducts.com.
Effects of hypothermia include: 1) 2) 3) 4) 5) 6) Unawareness of impending hazard Failure to perceive amount of heat Failure to recognize the need to exit the bathtub Physical inability to exit the bathtub Fetal damage in pregnant women Unconsciousness and danger of drowning Since excessive water temperatures have a high potential for causing fetal damage during the early months of pregnancy, pregnant or possibly pregnant should consult a physician before using a bathtub equipped at higher temperatures.
SAVE THESE INSTRUCTIONS Table of Contents Unpacking the Unit 5 Installation and Operation Guidelines 5 Rough-In Measurements 6 Freestanding Bath Installation Planning and Preparation 7 Freestanding Bath Installation Instructions 8 Cleaning Instructions 9 Warranty 11 ATTENTION INSTALLER! Access should be provided to the plumbing connections and should have a minimum size of 16” x 14” for installation and future servicing of the bathtub.
Unpacking the Unit 1. Inspect the Carton. 2. If you note carton damage, take a picture and contact the carrier immediately. Do not install a damaged tub. Clarke Products is not responsible for damage during transit. 3. Immediately inspect the unit for damage even if there is no visible carton damage and immediately report any damage to the distributor/manufacturer. Once the unit is installed and there is surface damage visible, we will assume it was caused by the installer.
ATTENTION INSTALLER! This tub must be tested for leaks prior to installation. Failure to do so will void the warranty. This tub was tested at the factory and found to be fully operational and leak-free prior to shipping. Shipping, handling, and job site exposure may have deteriorated the tub’s condition. It is the responsibility of the installer to thoroughly test the tub prior to installation. Water Test Procedures 1. 2. 3. 4. 5. Place the tub on a level surface. Seal the drain.
Note: some tubs come standard with integral slotted overflows. Others come pre-drilled for traditional round overflows. Be sure to refer to actual product before installing, since this may also be an “option” created at time order was placed. Illustration A Installation Planning and Preparation 1. Determine the final location of the tub. The tub will sit on top of the finished floor but the drain (and overflow piping, if applicable) may sit below the finished floor.
Freestanding Bath Installation Instructions 1. Tip the tub over to install the drain and overflow if applicable. Use care not to damage the solid surface/acrylic finish by using suitable material to protect the finish of the tub. 2. For non-integral overflow tubs, install the drain and overflow per manufacturer’s instructions. For integral overflow tubs, install the drain per manufacturer’s instructions.
Cleaning and Maintenance Cleaning Instructions for Acrylic Models The cross-linked acrylic surface of all Clarke Products acrylic freestanding tubs is one of the glossiest, highest quality surfaces available. Its hard, non-porous surface prevents dirt from accumulating and resists stains. Under normal use, the acrylic surface will retain its beauty with only a minimal amount of care.
Cleaning Instructions for Solid Surface Models The cast surface of all Clarke Products solid surface freestanding tubs is one of the highest quality surfaces available. The matte finish is design to provide an elegant, durable finish. Its hard, nonporous surface prevents dirt from accumulating and resists stains. Under normal use, the solid surface will retain its beauty with only a minimal amount of care.
LIMITED WARRANTY All CLARKE PRODUCTS Solid Surface and Free Standing Acrylic Bathing Tubs are warranted in accordance with the following Limited Warranty: CLARKE PRODUCTS Solid Surface and Free Standing Acrylic are warranted against defects in material and workmanship from the date of the first consumer purchase. Solid Surface & Free Standing Acrylic warranty is 2 years.
