E Operator's Manual Libro De Instrucciones Manuel D’utilisation C2K Series 120V Polisher READ THIS BOOK CAUTION: Read the Operator's Manual before using the appliance. This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your ALTO machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well.
CONTENTS OF THIS BOOK Operator Safety Instructions ............................................................................................... 5 Machine Introduction .......................................................................................................... 6 Accessories ..................................................................................................................... 11 Machine Specifications .............................................................................
C2K Series LIBRO DE INSTRUCCIONES LEA ESTE LIBRO CUIDADO: Lea el Libro de Instrucciones antes de usar este aparato. Contiene información importante para el uso y funcionamiento correcto y seguro de la máquina. Lea este libro completamente antes de arrancar la máquina o hacer cualquier operación de mantenimiento. Si non sigue las instrucciones, corre el peligro de herirse o causar lesiones al personal, o causar daños importantes a la máquina o a su entorno.
C2K Series MANUEL D’UTILISATION LISEZ CE MANUEL ATTENTION: Lire le manuel d'utilisation avant de faire fonctionner l'appareil. Il contient des informations importantes pour une utilisation correcte de la machine, en toute sécurité. Lisez-le complètement avant de mettre la machine en marche ou d’effectuer un entretien. A défaut, vous risqueriez de vous blesser ou de blesser d’autres membres du personnel, d’endommager sérieusement la machine ou de provoquer des dégâts dans son environnement.
OPERATOR SAFETY INSTRUCTIONS WARNING AVERTISSEMENT ADVERTENCIA DANGER means: Severe bodily injury or death can occur to you or other personnel if the DANGER statements found on this machine or in this Owner's Manual are ignored or are not adhered to. Read and observe all DANGER statements found in this Owner's Manual and on your machine.
OPERATOR SAFETY INSTRUCTIONS (cont.) WARNING: Use of this machine as a step or furniture could result in injury or damage. Do not use this machine as a step or furniture. Do not ride on this machine. WARNING: To avoid injury keep hands, feet and loose clothing away from all moving parts of this machine. WARNING: Injury to operator or bystanders could occur if an abrupt change in floor surface texture is encountered when using this machine.
INSTRUCCIONES PARA LA SEGURIDAD DEL OPERADOR WARNING AVERTISSEMENT ¡ AVISO ! ¡ PELIGRO ! : Si no sigue la indicación PELIGRO, se pueden causar lesiones graves, incluso mortales. Lea y siga todas las indicaciones PELIGRO que se encuentran en el libro y en la máquina. ¡ AVISO ! : Si no sigue la indicación AVISO, se pueden causar lesiones sea al operador sea a otro personal y/o daños materiales. Lea y siga todas las indicaciones AVISO que se encuentran en el libro y en la máquina.
¡ AVISO ! Use siempre un cable con tres conductores puestos a tierra. Para una protección óptima, conecte la máquina con una caja de enchufe conectada con la red que tiene un diferencial. Si tiene alguna duda, sírvase acudir a un eléctrico cualificado. ¡ AVISO ! Para evitar daños al cable de alimentación, procure que el cepillo, el disco, el portadisco o las ruedas no toquen el cable, cuando la máquina funciona. Levante siempre el cable por encima de la máquina.
INSTRUCTIONS POUR LA SECURITE DE L’OPERATEUR WARNING AVERTISSEMENT ¡ AVISO ! ! DANGER ! Le non-respect des consignes précédées du mot DANGER peut occasionner des blessures graves, voire entraîner la mort. Lisez et respectez toutes les consignes DANGER figurant dans ce manuel et sur la machine. AVERTISSEMENT Le non-respect des consignes AVERTISSEMENT peut entraîner des blessures pour l’opérateur ou d’autres membres du personnel et/ou occasionner des dégâts matériels.
AVERTISSEMENT Utiliser toujours un câble à trois conducteurs, relié à la terre. Pour une protection optimale, branchez la machine sur une prise réseau équipé d’un différentiel. En cas de doute, veuillez faire appel à un électricien qualifié. AVERTISSEMENT Pour éviter d’endommager le câble d’alimentation, veillez à ce que la brosse, le disque, le porte-disque ou les roues ne touchent pas le câble, lorsque la machine fonctionne. Soulevez toujours le câble au-dessus de la machine.
ACCESSORIES The following accessories are available. 5. Synthetic pads for polishing, scrubbing, stripping and spray buffing. 6. Brushes with metal or wood backs and with holes to let the solution flow through. 1. Polishing and waxing brushes. 2. Brushes with natural or synthetic bristles for scrubbing. 7. Solution tank. 3. Brushes with steel wire bristles. 8. Sanding discs. 4. Synthetic pad holders. 9.
ACCESORIOS Los accesorios siguientes son disponibles : 1. Cepillos para encerar y pulir. 2. Cepillos para fregar con filamentos en fibras naturales o sintéticas. 3. Cepillos de alambre de acero. 4. Portadiscos sintéticos. 5. Discos sintéticos para pulir, fregar, decapar y lustrar con tampón. 6. Cepillos con el dorso de metal o de madera y con canales para dispersar la solución. 7. Depósito de solución. 8. Discos para pulir. 9. Juego de accesorios para lustrar por pulverización con tampón.
ACCESSOIRES Les accessoires suivants sont disponibles: 1. 2. 3. 4. 5. Brosses pour cirer et polir Brosses de récurage, avec brins en fibres naturelles ou synthétiques. Brosses avec brins en acier Porte-disques synthétiques Disques synthétiques pour le polissage, le récurage, le décapage et le lustrage au tampon.
Machine Specifications Model Code Number Voltage (Volts) Frequency (Hz) Current (Amps) Power (hp) Brush Diameter (inches) Block Diameter (inches) Brush Speed (rpm) Cord Length (feet) Weight (pounds) C2K-16 01194A 120 60 12 0.75 16 14 175 50 88 C2K-18 01195A 120 60 12 0.
Especificaciones de la pulidora C2K Modelo Número de código Tensión (V) Frecuencia (Hz) Corriente (A) Potencia (hp) Diámetro del cepillo (pulgadas) Diámetro del bloque (pulgadas) Velocidad del cepillo (rpm) Longitud del cable de añadido (pies) Peso (libras) C2K-16 01194A 120 60 12 0.75 16 14 175 50 C2K-18 01195A 120 60 12 0.
Spécifications de la cireuse de série C2K Modèle Numéro de code Tension (volts) Fréquence (Hz) Courant (Amps) Puissance (hp) Diamètre de brosse (pouces) Diamètre du bloc (pouces) Vitesse de brosse (rpm) Longuer du cordon (pieds) Poids (livers) C2K-16 01194A 120 60 12 0.75 16 14 175 50 88 C2K-18 01195A 120 60 12 0.
NOTES CLARKE TECHNOLOGY Operator's Manual - C2K Series 120V Page - 17 -
HOW TO PREPARE THE MACHINE FOR OPERATION WARNING: Always remove the electrical plug from the electrical outlet before installing or changing the pad or brush. How To Install The Brush Or Pad Driver To install the brush or pad driver, follow this procedure: 1. Put the handle in the vertical position. Figure 1 2. To lock the handle, push the locking lever down.See figure 1. 3. Tilt the machine backward until the handle is on the floor. See figure 2. 4. Put one foot on each side of the machine. See figure 2.
PREPARACION DE LA MAQUINA PARA TRABAJAR AVISO : Desconecte siempre el enchufe de la caja de enchufe conectada con la red antes de instalar o cambiar el disco o el cepillo. PREPARATION DE LA MACHINE AVANT LA MISE EN SERVICE AVERTISSEMENT: Débranchez toujours la fiche de la prise réseau avant d’installer ou de changer le disque ou la brosse. Cómo instalar el cepillo o el portadisco Para instalar una cabeza de cepillo o un portadisco, sigue este procedimiento : 1. 2. 3. 4. 5. 6. 7. 8.
120 VOLT MACHINES Instructions for connection to the power supply and the electrical ground. This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electrical shock. This product is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate oulet that is properly installed and grounded in accordance with all local codes and ordinances.
MAQUINAS 120 V. MACHINES 120 V. INSTRUCCIONES PARA LA CONEXION ELECTRICA DE LA MAQUINA INSTRUCTIONS POUR LE RACCORDEMENT ELECTRIQUE La máquina debe ser puesta a tierra. En caso de mal funcionamiento o de avería, el hilo de tierra es un camino de menor resistencia que permite el paso de corriente ; por lo cual se reduce el riesgo de choque eléctrico. La máquina tiene un cable de alimentación con tres conductores y un enchufe con tres clavijas de las cuales una está puesta a tierra.
HOW TO OPERATE THE MACHINE How To Start/Stop The Machine 1 WARNING: Never start a polisher when the handle is in the vertical position. The following step applies to the C2K-1600DS and C2K2000DS only:Select high or low speed with the switch located on the motor cover. Moving the switch lever up selects high speed. Moving the switch lever down selects low speed.
FUNCIONAMIENTO DE LA MAQUINA MISE EN SERVICE DE LA MACHINE Arranque y parada Mise en Marche et Arrêt AVISO : Nunca arranque una pulidora cuando la tobera está en posición vertical. Sólo para el modelo C2K-1600DS, C2K-2000DS: Seleccione la velocidad (alta o moderada - high o low) por medio del interruptor situado en la tapa del motor. Velocidad alta : la palanca está empujada hacia arriba. Velocidad moderada : la palanca está empujada hacia abajo.
NOTES Page -24 - CLARKE TECHNOLOGY Operator's Manual - C2K Series 120V
C2K Series 120V Section II Parts and Service Manual (70152A) CLARKE TECHNOLOGY Operator's Manual - C2K Series 120V Page - 25 -
MAINTENANCE WARNING: Maintenance must be done by authorized personnel only. CAUTION: Keep all adjustments according to specifications. Maintenance Instructions Return the machine to a Clarke Technology Authorized Service Location every 12 months for maintenance inspections. Switches WARNING: All electrical repairs must be done by authorized personnel only. The machine must be tested after electrical repairs to make sure it is safe to operate.
MANTENIMIENTO ENTRETIEN AVISO: El mantenimiento debe ser efectuadopor un técnico autorizado. AVERTISSEMENT:L'entretien doit toujours être effectué par un technicien agréé. PRUDENCIA:Todos los reglajes deben ser realizados conforme a las indicaciones descritas en este libro. PRUDENCE: Tous les réglages doivent être réalisés conformément aux indications figurant dans ce manuel.
CLARKE TECHNOLOGY C2K-16, C2K-18, C2K-160, C2K-180, C2K-200, C2K-1600, C2K-1800, C2K-2000, C2K-160HS, C2K-180HS, C2K-200HS Assembly Drawing 2/01 1 2 5 4 3 46 4 6 3 10 40 47 7 1 8 13 1 9 11 41 10 31 39 21 38 22 43 20 19 17 24 23 29 1 44 16 37 14 26 18 42 30 25 26 22 28 15 25 32 1 23 27 33 24 34 36 Page -28 - CLARKE TECHNOLOGY Operator's Manual - C2K Series 120V
CLARKE TECHNOLOGY C2K-16, C2K-18, C2K-160, C2K-180, C2K-200, C2K-1600, C2K-1800, C2K-2000, C2K-160HS, C2K-180HS, C2K-200HS Assembly Drawing Parts List 2/01 Ref. Part No.
CLARKE TECHNOLOGY C2K-1600DS and C2K-2000DS Assembly Drawing 2/01 1 2 3 55 57 5 4 6 3 41 7 10 40 4 9 42 8 1 56 13 54 44 43 49 39 46 21 38 22 50 47 31 20 16 1 24 23 19 17 37 14 52 26 51 18 25 26 22 15 25 28 45 30 1 30a 23 32 27 24 1 48 10 33 29 34 36 Page -30 - CLARKE TECHNOLOGY Operator's Manual - C2K Series 120V
CLARKE TECHNOLOGY C2K-1600DS and C2K-2000DS Assembly Parts List 2/01 Ref. 1 2 3 4 5 6 7 8 9 10 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 30a 31 32 33 Note: K indicates a change has been made since last publication of this manual 34 36 37 38 40 41 42 43 44 45 46 47 48 49 50 51 52 54 55 56 57 Part No.
CLARKE TECHNOLOGY C2K-16, C2K-18, C2K-160, C2K-180, C2K-200, C2K-160HS, C2K-180HS and C2K-200HS 120V - 60 Hz Motor Assembly Drawing & Parts List 9/99 Note: If your machine has motor #44635A refer to this drawing for service part replacement. 13 1 2 8 3 9 10 11 12 14 15 16 7 4 5 18 17 6 Ref. Part No. 1 2 3 4 5 6 7 8 9 58030A 52018A 52019A 54330A 737502 58028A 50400A 58029A 902550 Description Screw #10-32 x.31 LG.
CLARKE TECHNOLOGY C2K-16, C2K-18, C2K-160, C2K-180 and C2K-200 Gearbox Assembly Drawing & Parts List 2/01 Note: If your machine has gearbox #54409A refer to this drawing for service part replacement. Note: K indicates a change has been made since last publication of this manual 1 2 3 4 5 6 7 8 9 21 10 11 4 12 4 14 Ref. Part No. 1 2 3 4 5 6 7 8 9 10 11 12 14 15 16 17 18 19 20 21 80141A K Screw, Socket Hd. Cap Description Qty.
CLARKE TECHNOLOGY C2K-160HS, C2K 180HS and C2K 200HS Gearbox Assembly Drawing & Parts List 2/00 Note: If your machine has gearbox #50884A or #52093A refer to this drawing for service part replacement. 1 Note: K indicates a change has been made since the last publication of this manual. 3 4 6 7 8 9 20 10 11 Part No. Description 1 2 3 4 5 6 7 8 9 10 11 12 80141AK Screw, Socket Hd.
Note: CLARKE TECHNOLOGY C2K-1600, C2K-1800, C2K-2000 Motor Assembly Drawing & Parts List 9/00 If your machine has motor #50858A or #50858B refer to this drawing for service part replacements. 6 1 2 3 4 2a 5 2b Ref.
CLARKE TECHNOLOGY C2K-1600, C2K-1800, C2K-2000 Gearbox Assembly Drawing & Parts List 2/01 NOTE: If your machine has gearbox #50851A, refer to this drawing for service part replacement. Note: K indicates a change has been made since last publication of this manual Page -36 - Ref 1 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Part No. 80141AK 902606 58520A 50852A 962794 54858A 902736 58314A 442473 58313A 902737 N/A 54408A 58312A 902573 54856A 50851A Description Screw, Socket Hd.
CLARKE TECHNOLOGY C2K-1600DS and C2K-2000DS 120V Motor Assembly Drawing & Parts List 2/01 NOTE: If your machine has motor/gearbox #44651A, refer to this drawing for service part replacement. 1 1 2 3 20 15 4 10 14 6 6 5 19 6 6 7 16 18 9 11 8 7 9 9 17 12 13 Note: Kindicates a change has been made since last publication of this manual Ref 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Part No.
CLARKE TECHNOLOGY C2K-1600DS and C2K-2000DS Gearbox Assembly Drawing & Parts List 2/01 NOTE: If your machine has gearbox #63602A, refer to this drawing for service part replacement. 18 17 19 16 4 11 4 12 10 8 13 14 13 15 9 7 6 5 4 3 1 Note: K indicates a change has taken place since last publication of this manual Page -38 - Ref 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Part No. Description 80141AK Screw, Socket Hd. Cap Qty.
CLARKE TECHNOLOGY C2K-16, C2K-18, C2K-160, C2K-180, C2K-200, C2K-1600, C2K-1800, C2K-2000, C2K-160HS, C2K-180HS, C2K-200HS Wiring Diagram 120V-60Hz 9/99 CLARKE TECHNOLOGY C2K-1600DS and C2K-2000DS Wiring Diagram 120V 9/99 WARNING: All electrical repairs must be performed by qualified personnel only.
NOTES
ALTO® PRODUCT SUPPORT BRANCHES U. S. A. Locations HEAD OFFICE European Locations PRODUCTION FACILITIES ALTO U.S. Inc., St. Louis, Missouri 16253 Swingley Ridge Road, Suite 200 Chesterfield, Missouri 63017-1725 PRODUCTION FACILITIES ALTO U.S. Inc., Springdale, Arkansas 2100 Highway 265 Springdale, Arkansas 72764 (501) 750-1000 Customer Service - 1-800-253-0367 Technical Service - 1-800-356-7274 ALTO U.S. Inc., Bowling Green, Ohio 43402 1100 Haskins ALTO U.S. Inc., Clearwater, Florida 33765 1500 N.
CLARKE TECHNOLOGY LIMITED U.S. WARRANTY This ALTO Industrial/Commercial Product is warranted to be free from defects in materials and workmanship under normal use and service for a period of five years from the date of purchase, when operated and maintained in accordance with Clarke Technology's Maintenance and Operations Instructions. This warranty is extended only to the original purchaser for use of the product. It does not cover normal wear parts such as electrical cable, rubber parts and motor brushes.
