Division of Operator's Manual C.A.V. 15 CLARKE-AMERICAN Vacuum 15 Gallon READ THIS BOOK This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke American Sanders machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine before using it.
Table of Contents Important Safety Instructions .................................................................................... 3 Specifications and Accessories .............................................................................. 5 Grounding Instructions ............................................................................................. 6 How To Assemble the Machine ............................................................................... 7 Machine Operation .................
IMPORTANT SAFETY INSTRUCTIONS WARNING AVERTISSEMENT ADVERTENCIA DANGER: Failure to read and observe all DANGER statements could result in severe bodily injury or death. Read and observe all DANGER statements found in your Owner's Manual and on your machine. WARNING: Failure to read and observe all WARNING statements could result in injury to you or to other personnel; property damage could occur as well. Read and observe all WARNING statements found in your Owner's Manual and on your machine.
Page -4- DANGER: Failure to read the Owner's Manual prior to operating or attempting any service or maintenance procedure to your machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine before using it. If your operator(s) cannot read English, have this manual explained fully before attempting to operate this machine.
SPECIFICATIONS & ACCESSORIES Model C.A.V. 15 Voltage 120 V Frequency Power 60 Hz 1200 Watts Connected load for appliance plug socket 600 Watts Volume Flow (air) Static Water Lift 120 CFM 90" Filter Surface Area 3-Stage 2,212 sq. inches Sound Level Cord Length 58 db(A) 22' Tank Volume Width 15 gal. 17" Depth Height 17" 26" Weight Order # for bag-type 33 lbs. 52850A filter elements (pack of 5 elements) Order # for filter element 29747 H.E.P.A.
GROUNDING INSTRUCTIONS This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipmentgrounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
HOW TO ASSEMBLE THE MACHINE CAUTION! On delivery, the accessories - are lying in the tank and must be removed before the machine is used for the first time. See figure 2. To assemble the machine, remove the machine top section: The power cord must not yet be inserted into a plug socket. 1. Open the retaining clamps and lift off the machine top section (Figure 3). 2. Place a bag-type filter into the tank as described in the instructions printed on the filter. 3.
MACHINE OPERATION Changing The Bag Type Filter 1. Close the bag-type filter sleeve with the slide (Figure 4). 2. Pull the bag-type filter sleeve off the inlet fitting. 3. Dispose of the used bag-type filter in accordance with the local waste disposal regulations. 4. Place a new bag-type filter into the tank as described in the instructions printed on the filter. IMPORTANT! Push the bag-type filter sleeve completely onto the inlet fitting. Figure 4 Replacing The Filter Element 1.
TROUBLESHOOTING Problem Motor does not start. Reduced suction power. No suction power during wet cleaning. Cause Action 1. The fuse or plug socket has blown. 1. Reset the fuse 2. Overload protection switch has tripped. 2. Allow the machine to cool down approximately 5 minutes; if the machine does not start again automatically, contact the Service Dept. 1. Bag-type filter full. 1. Replace bag-type filter. 2. Suction hose clogged. 2. Clean suction hose. 3. Filter element clogged. 3.
NOTES Page -10- Clarke® American Sanders C.A.V.
Division of C.A.V. 15 Wet/Dry Vacuum Section II Parts and Service (70641B) Page -11Clarke® American Sanders C.A.V. 15 Operator's Manual Page -11CLARKE-AMERICAN SANDER TECHNOLOGY C.A.V.
C.A.V. 15 Assembly Drawing 8/02 Page -12- Clarke® American Sanders C.A.V.
C.A.V. 15 Assembly Parts List 8/02 Ref. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 23 24 25 26 27 29 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 NI NI Part No.
NOTES Page -14- Clarke® American Sanders C.A.V.
PRODUCT SUPPORT BRANCHES U. S. A. Locations HEAD OFFICE European Locations PRODUCTION FACILITIES ALTO U.S. Inc., St.
Clarke® American Sanders U. S. Warranty This Clarke American Sanders Industrial/Commercial Product is warranted to be free from defects in materials and workmanship under normal use and service for a period of two years from the date of purchase, when operated and maintained in accordance with Clarke American Sanders's Maintenance and Operations instructions. This warranty is extended only to the original purchaser for use of the product.
Division of Operator's Manual LIBRO DE INSTRUCCIONES Sander 1600DC MANUEL D’UTILISATION READ THIS BOOK CAUTION: Read the Operator's Manual before using the appliance. This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke American Sanders machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well.
CONTENTS OF THIS BOOK Operator Safety Instructions ............................................................................................... 5 Machine Introduction .......................................................................................................... 6 Machine Specifications .................................................................................................... 11 How To Prepare the Machine for Operation .................................................................
Sander 1600 / 1600DC LIBRO DE INSTRUCCIONES LEA ESTE LIBRO CUIDADO: Lea el Libro de Instrucciones antes de usar este aparato. Contiene información importante para el uso y funcionamiento correcto y seguro de la máquina. Lea este libro completamente antes de arrancar la máquina o hacer cualquier operación de mantenimiento. Si non sigue las instrucciones, corre el peligro de herirse o causar lesiones al personal, o causar daños importantes a la máquina o a su entorno.
Sander 1600 / 1600DC MANUEL D’UTILISATION LISEZ CE MANUEL ATTENTION: Lire le manuel d'utilisation avant de faire fonctionner l'appareil. Il contient des informations importantes pour une utilisation correcte de la machine, en toute sécurité. Lisez-le complètement avant de mettre la machine en marche ou d’effectuer un entretien. A défaut, vous risqueriez de vous blesser ou de blesser d’autres membres du personnel, d’endommager sérieusement la machine ou de provoquer des dégâts dans son environnement.
OPERATOR SAFETY INSTRUCTIONS WARNING AVERTISSEMENT ADVERTENCIA DANGER means: Severe bodily injury or death can occur to you or other personnel if the DANGER statements found on this machine or in this Owner's Manual are ignored or are not adhered to. Read and observe all DANGER statements found in this Owner's Manual and on your machine.
OPERATOR SAFETY INSTRUCTIONS (cont.) WARNING: Operating a machine without observing all labels and instructional information could result in injury or damage. Read all machine labels before attempting to operate. Make sure all of the labels and instructional information are attached or fastened to the machine. Get replacement labels and decals from your authorized distributor. WARNING: Use of this machine as a step or furniture could result in injury or damage.
INSTRUCCIONES PARA LA SEGURIDAD DEL OPERADOR WARNING AVERTISSEMENT ¡ AVISO ! ¡ PELIGRO ! : Si no sigue la indicación PELIGRO, se pueden causar lesiones graves, incluso mortales. Lea y siga todas las indicaciones PELIGRO que se encuentran en el libro y en la máquina. ¡ AVISO ! : Si no sigue la indicación AVISO, se pueden causar lesiones sea al operador sea a otro personal y/o daños materiales. Lea y siga todas las indicaciones AVISO que se encuentran en el libro y en la máquina.
¡ AVISO ! Hay un riesgo de cortocircuito si los componentes eléctricos de una máquina están expuestos a la humedad o son mojados. Procure que los componentes eléctricos sean siempre secos. Seque cuidadosamente la máquina después de cada utilización. Guarde la máquina en un local seco. ¡ AVISO ! Use siempre un cable con tres conductores puestos a tierra. Para una protección óptima, conecte la máquina con una caja de enchufe conectada con la red que tiene un diferencial.
INSTRUCTIONS POUR LA SECURITE DE L’OPERATEUR WARNING AVERTISSEMENT ¡ AVISO ! ! DANGER ! Le non-respect des consignes précédées du mot DANGER peut occasionner des blessures graves, voire entraîner la mort. Lisez et respectez toutes les consignes DANGER figurant dans ce manuel et sur la machine. AVERTISSEMENT Le non-respect des consignes AVERTISSEMENT peut entraîner des blessures pour l’opérateur ou d’autres membres du personnel et/ou occasionner des dégâts matériels.
AVERTISSEMENT Risque de court-circuit si les composants électriques d’une machine ont été exposés à l’humidité ou sont mouillés. Veillez à ce que les composants électriques soient toujours secs. Essuyer soigneusement la machine après chaque utilisation. Entreposer la machine dans un local sec. AVERTISSEMENT Utiliser toujours un câble à trois conducteurs, relié à la terre. Pour une protection optimale, branchez la machine sur une prise réseau équipé d’un différentiel.
Machine Specifications Model Code Number Voltage (Volts) Frequency (Hz) Current (Amps) Power (hp) Pad Diameter Pad Speed (rpm) Cord Length (feet) Weight (pounds) Sander 1600DC 07101B 120 60 14 1.5 16.0 175 50 121 Modelo Número de código Tensión (V) Frecuencia (Hz) Corriente (A) Potencia (hp) Diámetro del disco Velocidad de rotation del disco(rpm) Longitud del cable de añadido (pies) Peso (libras) Sander 1600DC 07101B 120 60 14 1.5 16.
HOW TO PREPARE THE MACHINE FOR OPERATION WARNING: Always remove the electrical plug from the electrical outlet before installing or changing the sandpaper. How To Install The Sandpaper To install the sandpaper, follow this procedure: 1. Put the handle in the vertical position. Figure 1 2. Lock the handle. To lock the handle, push the locking lever down. See figure 1. 3. Tilt the machine backward until the handle is on the floor. 4. Put one foot on each side of the machine. 5.
PREPARACION DE LA MAQUINA PARA TRABAJAR PREPARATION DE LA MACHINE AVANT LA MISE EN SERVICE ADVERTENCIA: Antes de instalar o cambiar ATTENTION: Débrancer toujours la prise de la el papel abrasivo, desconecte siempre el enchufe de source d'alimentation électrique avant d'installer la toma de corriente. ou de changer le papier abrasif.
HOW TO PREPARE THE MACHINE FOR OPERATION (cont.) Grain Standard Grade Part #/Qty Use Professional Grade Part #/Qty 945566/25 945567/25 945568/25 945569/50 12 grit 16 grit 20 grit 24 grit For removing gross imperfections and restore evenness to old flooring. To remove build-up of paints and varnishes. 945342/25 945343/25 945344/25 30 grit 36 grit For first sanding of new flooring (maple, oak). For removing minor imperfections and finishes from old flooring.
Grano Empleo Grado estándar Sólo parte # Grado profesional Sólo parte # 945342/25 945343/25 945344/25 945566/25 945567/25 945568/25 945569/50 grano 30 grano 36 Para pulimentar por primera vez un suelo nuevo (arce, roble). Para quitar las imperfecciones pequeñas y el acabado de suelos usados 945347/50 945570/50 945571/50 grano 50 Para pulimentar por primera vez un suelo nuevo (cedro, pino, abeto). 945349/50 Para limpieza de 16 granos.
HOW TO PREPARE THE MACHINE FOR OPERATION WARNING: Always remove the electrical plug from the electrical outlet before installing or changing the pad or brush. How To Install The Brush Or Pad Driver To install the brush or pad driver, follow this procedure: Figure 4 1. Put the handle in the vertical position. 2. To lock the handle, push the locking lever down.See figure 4. 3. Tilt the machine backward until the handle is on the floor. See figure 5. 4. Put one foot on each side of the machine. See figure 5.
PREPARACION DE LA MAQUINA PARA TRABAJAR AVISO : PREPARATION DE LA MACHINE AVANT LA MISE EN SERVICE AVERTISSEMENT: Desconecte siempre el enchufe de la caja de enchufe conectada con la red antes de instalar o cambiar el disco o el cepillo. Débranchez toujours la fiche de la prise réseau avant d’installer ou de changer le disque ou la brosse. Cómo instalar el cepillo o el portadisco Para instalar una cabeza de cepillo o un portadisco, sigue este procedimiento : 1. 2. 3. 4. 5. 6. 7. 8.
HOW TO PREPARE THE MACHINE FOR OPERATION How to Install the Dust Control Skirt To install the skirt, follow this procedure: 1. Wrap the skirt around the bumper such that the draw string can be inserted into the recess of the bumper. See figure 7. Figure 7 2. Orient the brush fastening strap at the rear of the machine to prevent scratching surfaces. 3. Tighten and tie the string on the skirt into a bow knot so it can later be untied for removal of the skirt. 4.
Preparación de la máquina para trabajar Préparation de la machine avant la mise en service Cómo instalar la falda Installation de la Jupe Para instalar la falda, siga este procedimiento: Pour installer la jupe, suivre la procédure suivante : 1. Envelopper la jupe autour du pare-chocs afin que la ficelle de tirage puisse être insérée dans l’enfoncement du pare-chocs. Voir illustration 7. 1. 2. 3. 4.
120 VOLT MACHINES Instructions for connection to the power supply and the electrical ground. This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electrical shock. This product is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate oulet that is properly installed and grounded in accordance with all local codes and ordinances.
MAQUINAS 120 V. MACHINES 120 V. INSTRUCCIONES PARA LA CONEXION ELECTRICA DE LA MAQUINA INSTRUCTIONS POUR LE RACCORDEMENT ELECTRIQUE La máquina debe ser puesta a tierra. En caso de mal funcionamiento o de avería, el hilo de tierra es un camino de menor resistencia que permite el paso de corriente ; por lo cual se reduce el riesgo de choque eléctrico. La máquina tiene un cable de alimentación con tres conductores y un enchufe con tres clavijas de las cuales una está puesta a tierra.
HOW TO OPERATE THE MACHINE 1 How To Start/Stop The Machine WARNING: Never start machine when the handle is in the vertical position. The switch to start and stop the machine is activated by the interlock switch (1) and the levers (2) under the handle grips. See figure 10. To start the machine, follow this procedure: 2 2 Figure 10 1. Lower the handle 2. Lock the handle in the best position for operation. NOTE: Make sure you hold the handle with both hands. 3.
FUNCIONAMIENTO DE LA MAQUINA MISE EN SERVICE DE LA MACHINE Arranque y parada Mise en Marche et Arrêt AVISO : Nunca arranque la maquina cuando la tobera está en posición vertical. AVERTISSEMENT: Ne jamais mettre la machine en marche lorsque le timon est en position verticale. El interruptor de arranque/parada se opera empujando el botón de cierre de seguridad (1) y usando las palancas (2) situadas debajo del mango de mando (Véase fig. 8). Para arrancar la máquina, siga este procedimiento : 1.
MAINTENANCE WARNING: Maintenance must be done by authorized personnel only. Maintenance Instructions Return the machine to a Clarke American Sanders Authorized Service Location every 12 months for maintenance inspections. MANTENIMIENTO AVISO : El mantenimiento debe ser efectuado por untécnico autorizado. Instrucciones para el mantenimiento Cada 12 meses, la máquina debe ser mandada a un centro técnico autorizado Clarke American Sanders para ser comprobada.
Division of Sander 1600DC Section II Parts and Service Manual (70408B) Clarke® American Sanders Operator's Manual - Sander 1600DC Page - 25 -
MAINTENANCE WARNING: Maintenance must be done by authorized personnel only. CAUTION: Keep all adjustments according to specifications. Maintenance Instructions Return the machine to a Clarke American Sanders Authorized Service Location every 12 months for maintenance inspections. Switches WARNING: All electrical repairs must be done by authorized personnel only. The machine must be tested after electrical repairs to make sure it is safe to operate.
MANTENIMIENTO ENTRETIEN AVISO: El mantenimiento debe ser efectuadopor un técnico autorizado. AVERTISSEMENT:L'entretien doit toujours être effectué par un technicien agréé. PRUDENCIA:Todos los reglajes deben ser realizados conforme a las indicaciones descritas en este libro. PRUDENCE: Tous les réglages doivent être réalisés conformément aux indications figurant dans ce manuel.
Sander 1600DC Assembly Drawing 2/03 1 2 14 15 16 5 4 3 13 1 12 19 18 8 23 24 25 28 9 11 10 26 37 38 1 29 31 30 66 27 74 36 34 36 32 35 33 73 35 35 25 40 75 70 72 71 69 65 67 68 59 55 64 37 35 1 3 7 21 22 20 17 4 6 41 38 56 57 58 59 42 39 43 60 62 61 63 44 45 49 46 47 48 50 76 53 54 52 51 77 (includes 51, 52, & 76) Page -28 - Clarke® American Sanders Operator's Manual - Sander 1600DC
Sander 1600DC Assembly Drawing Parts List 2/03 Ref. Part No.
Sander 1600DC Lamp Assembly Drawing 10/01 1 2 4 3 4 5 21 6 7 22 4 20 8 19 9 10 13 11 14 15 16 17 12 18 17 Page -30 - Clarke® American Sanders Operator's Manual - Sander 1600DC
Sander 1600DC Lamp Assembly Drawing Parts List 10/01 Ref. Part No.
Sander 1600DC Gearbox Assembly and Parts List 18 17 19 13 4 11 4 12 13 10 8 14 15 9 7 6 5 4 3 1 2 Ref 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 NI Page -32 - Part No. 962966 980650 56922A 902606 58520A N/A 962794 54858A 902736 58314A 442473 58313A 902737 N/A 54408A 58312A 902573 54856A 50979A 503802 Description Screw, Socket Hd.
Sander 1600DC WARNING: All electrical repairs must be performed by qualified personnel only.
NOTES
PRODUCT SUPPORT BRANCHES U. S. A. Locations HEAD OFFICE European Locations PRODUCTION FACILITIES ALTO U.S. Inc., St.
Clarke® American Sanders U. S. Warranty This Clarke American Sanders Industrial/Commercial Product is warranted to be free from defects in materials and workmanship under normal use and service for a period of five years from the date of purchase, when operated and maintained in accordance with Clarke American Sanders's Maintenance and Operations Instructions. All handle components are warranted for 5 years to be free from defects in material or workmanship under normal use and service.
