Order Parts Here: www.ivie-ent.com/parts Ph:(918)254-5161 BEXT®-100, 100H, 150H, 300HV 120V Extractor's Operator's Manual Manual del Operador Manuel de l'operateur READ THIS BOOK This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well.
CONTENTS OF THIS BOOK Operator Safety Instructions .................................................................................. 5 Introduction and Machine Specifications .................................................................. 6 Controls and Machine Features ............................................................................... 12 How to Prepare the Machine for Operation .............................................................. 14 Set-Up .......................................
OPERATOR SAFETY INSTRUCTIONS WARNING AVERTISSEMENT ADVERTENCIA For the safe operation of this machine, read and understand all warnings and cautions. DANGER means: Severe bodily injury or death can occur to you or other personnel if the DANGER statements found on your machine or in your Owner's Manual are ignored or are not adhered to. Read and observe all DANGER statements found in your Owner's Manual and on your machine.
OPERATOR SAFETY INSTRUCTIONS (CONT.) WARNING: Improper discharge of waste water may damage the environment and be illegal. The United States Environmental Protection Agency has established certain regulations regarding discharge of waste water. Also, city and state regulation regarding this discharge may be in effect in your area. Understand and follow the regulations in your area. Be aware of the environmental hazards of chemicals that you dispose.
1B 1A 1H CONTROLS and MACHINE FEATURES 1C 1D The Vacuum Motor Switches See Figure 1-A The vacuum motor switches are located on the top of the machine. 1G 1F The Switch To Activate The Pump See Figure 1-B The switch to start/stop the pump motor is on the top of the machine. Press the lever on the floor tool to start the solution flow. Release the lever on the floor tool to stop the solution flow.
HOW TO PREPARE THE MACHINE FOR OPERATION To prepare the machine for operation, follow this procedure: 1. Connect the vacuum hose to the hose connector on the extractor and to the end of the vacuum tube on the floor tool. See Figure 1 D, E 2. Connect the solution hose to the extractor and the floor tool. To fasten the quick disconnect fitting, slide the knurled collar on the female coupling away from the opening. Push the male coupling into the female coupling.
5. If the extractor removes an excess amount of foam from the carpet, add a de-foamer such as Clarkare® De-foamer Concentrate to the recovery tank. The amount needed will vary according to the amount of detergent already in the carpet. CAUTION: To prevent damage, use a water-based defoamer rather than an oil-based de-foamer. Do not leave the extractor or other cleaning machines or tools on the carpet when not in use.
BEXT®-150 H Control Panel 1 LOCATOR 2 MODE 3 4 5 6 VAC 1 VAC 2 PUMP HEAT Figure 6 CIRCUIT LOCATOR ( 1 ): When this light is on, it indicates that cord #2 is on a separate line from cord #1. Cord #2 supplies voltage to the heater allowing it to heat to the proper temperature range. HEAT MODE LIGHT ( 2 ): This light will only illuminate when the heater is heating and will turn off when it reaches operating temperature. VACUUM SWITCH ( 3 & 4): Each switch turns on one vac motor.
INSTRUCTIONS FOR CONNECTION TO THE POWER SUPPLY AND ELECTRICAL GROUND - 120 V CAUTION: Plate Screw Outlet must be connected to the electrical ground Ground Pin Figure 7 Tornillo de la placa Terminal de tierra El tomacorriente debe estar conectado al borne de puesta a tierra Figura 7 This machine will operate only on an AC frequency and on the specified electrical voltage shown on the nameplate. Make sure you have the correct frequency and voltage before connecting the power cord to an outlet.
MACHINE OPERATING INSTRUCTIONS Area 1 See figure 8 How to Clean an Area of Carpet See Figure 8A Superficie 1. Vea la Figura 8 WARNING: Zone 1 Voir figure 8 Do not use water that is hotter than 120°F (48°C).
MAINTENANCE WARNING: Maintenance and repairs must be done by authorized personnel only. Keep all fasteners tight. Use only genuine Clarke parts. WARNING: Do not operate this machine unless it is completely assembled. NOTE: For maintenance of the floor tools read the manual given with the tools. After Each Use of the Machine 1. Remove unused cleaning solution from the solution tank, by placing the end of the vacuum hose in the solution tank. Start the vacuum motor. Stop the motor when the tank is empty. 2.
MAINTENANCE (CONT) How To Prevent Damage From Freezing Temperatures To prevent damage from freezing temperatures follow this procedure: 1. Use the vacuum hose to remove all the solution from the clean solution tank. 2. Connect the solution hose to the extractor and a floor tool. 3. Put approximately 1 quart of antifreeze solution in the solution tank. Figure 9a 4. Put the switch for the pump in the "ON" position. 5. Put the end of the floor tool in the recovery pail. 6.
MAINTENANCE Maintenance Of The Motor This machine has a vacuum motor that uses carbon brushes. The carbon brushes in the motor must be checked every three months, or every 500 hours of operation, whichever comes first. If either of the brushes is shorter than 3/8 inch, replace both of the carbon brushes. GOOD UNEVEN SMALL HOLES GOOD A B GOOD HIGH MICA How To Check The Commutator And The Carbon Brushes WARNING: Electrical inspections must be made by a person authorized to make electrical repairs.
HOW TO CORRECT PROBLEMS IN THE MACHINE Problem The machine will not run. Cause Action 1. The machine has no power. 1. Make sure the machine is connected to the correct frequency and voltage, and all connections are tight. Make sure the plug is in the electrical outlet. There is no suction. 2. The power cord is damaged. 2. Contact an authorized service person to replace the cord. 1. The vac motor does not run. 1. Put the switch for the vacuum in the "I" position. 2.
BEXT®-100, 100H, 150H, 300HV Extractor Section II Parts and Service Manual (70416A) Clarke® BEXT®-100, 100H 150H, 300HV Operator's Manual Page 33
Clarke® BEXT®-100, 120V Assembly Drawing 7/06 Page 34 Clarke® BEXT® -100, 100H 150H, 300HV Operator's Manual
Clarke® BEXT®-100, 120V Assembly Drawing Parts List 7/06 Ref # 1 Part No. 53876A Description Drain Gate Qty 1 Ref # 34 Part No.
Clarke® BEXT®-100H, 120V Assembly Drawing 7/06 Page 36 Clarke® BEXT® -100, 100H 150H, 300HV Operator's Manual
Clarke® BEXT®-100H, 120V Assembly Drawing Parts List 7/06 Ref # 1 2 Part No. 53876A 80331A Description Drain Gate Screw, 8-32 x 5/8" 3 4 52636A 53877A Latch O-Ring 4A 4B 53878A 80332A 5 6 Qty 1 4 Ref # 34 39 Part No.
8 8A 86 Clarke® BEXT®-150H, 120V Assembly Drawing 11/05 Page 38 Clarke® BEXT® -100, 100H 150H, 300HV Operator's Manual
Clarke® BEXT®-150H, 120V Parts List 3/06 Ref # 1 1A 2 3 4 4A 4B 5 *6 *7 8 8A 8B 9 9A 10 Part No. 59721A 53606A 962929 52636A 837304 Description Valve-Drain Elbow-45 Degree, Drain Screw, 10-32 x 3/8 Latch, Tank O-Ring (Small) 920797 30322A 690212 692701 55674A 34288A 692409 85613A 81109A 52806A 2 1 1 1 1 1 1 1 1 1 11 12 13 14 15 15A 16 16A 17 18 19 20 20A 21 22 23 24 24A 25 26 27 27A 28 29 30 31 32 33 34 35 36 37 38 920797 Nut Drain Valve Lock Tank, Recovery Adaptor Asm.
Page 40 8 8B 1A 1 6 4 9A 9 Clarke® BEXT® 4B 104 8A 11 4A 7 10 4 81 81 82 13 80 15 73 5 22 Pri mi 72 28 e 32 s Ho 30 31 24A 24 21 86 97 ng 26 102 26A 27 70A 79 78 16 14 40 25 70B 65 71 17 34 47 38 90 98 23 33 70 26A 18 39 96 19 22 91 91 29 97 89 86 97 100 19A 20- 99 91 101 63 103 95 68 67 66 35 23 65 46 37 36 91 24 93 92 90 86 85 53 89 88 87 29 91 85 64 55 49 54 61 94 52 91 84 59 58 56 53 91 57
Clarke® BEXT®-300HV, 120V Parts List 3/06 Ref # 1 1A 2 3 4 4A 4B 5 *6 *7 8 8A 8B 9 9A 10 11 12 13 14 15 16 17 18 19 19A 20 21 22 23 24 24A 25 26 26A 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 46 47 49 50 51 52 53 Part No.
Clarke® BEXT -100 Accessories Drawing & Parts List 3/06 ® WARNING: Do not use Bext 100 accessories on heated units (Bext 100H, 150H & 300HV). Injury to operator or bystanders could occur. Damage to the machine could occur. 4A 6 3 7 8 9 11 4 10 2 5 1** Ref 1 2 3 4 4A 5 6 7 8 9 10 11 ASM NI Part No.
BEXT ® Clarke® 100H, 150H Detailer Accessories Drawing & Parts List 6/04 1B 1B 12A 1A 1B 3 4 5 6 7 12 1C 8 3 2 1 1** 2 9 11 10 Ref 1 1A 1B 1C 2 3 4 5 6 7 8 9 10 11 12 12A Part No. 61394A 30496A 52544A 52996A 52469A 52833A 398426 398425 398427 52953A 52832A 30229A 10386A 682408 52514A 53557A Description 12" Wand Hose Asm.
Clarke® BEXT® 300HV Accessories Drawing & Parts List 1/04 1B 1B 1A 1B 1C 8 2 1** 9 11 10 Ref 1 1A 1B 1C 2 3 4 5 6 7 8 9 10 11 Part No. 61395A 30496A 52544A 52996A 52469A 52833A 398426 398425 398427 52953A 52832A 30229A 10386A 682408 Description 12" Wand Hose Asm., Solution Valve Body Nozzle, Spray Hose 15' Tool, 3½ HP Defoamer Extractor, Concentrate Traffic Lane/Spot Cleaner General Purpose Spot Cleaner Tool, 4" Closed 15" Hose Extension Kit, 15" Hose Ext. w/Coupler 1.50 Dia.
Clarke® BEXT -150H, 120V Wiring Diagram 10/01 ® BEXT-150H EXTRACTOR WIRING DIAGRAM 120V BLACK CORD 1 WHITE GROUND ORANGE VAC 1 VAC 2 BLACK SW WHITE VACUUM VACUUM SW ORANGE WHITE FAN BLUE SW PUMP DUAL CORD SENSOR CIRCUIT BOARD P1 P2 P4 P3 BYPASS SWITCH P6 P7 P5 BLACK MODE LIGHT BLACK HEATER WHITE TC BLACK LOCATOR LIGHT CORD 2 GROUND 10/04/01 Page 46 Clarke® BEXT® -100, 100H 150H, 300HV Operator's Manual
