Specifications

9
3B) TOXIC FUME PREVENTION
Comply with precautions in 2B. Generator engine exhaust must be vented
to the outside air. Carbon monoxide can kill.
3C) FIRE AND EXPLOSION PREVENTION
Comply with precautions in 2C. Equipment’s rated capacity. Do not overload arc
welding equipment. It may overheat cables and cause a fire. Loose cable
connections may overheat or flash and cause a fire. Never strike an arc on a cylinder
or other pressure vessel. It creates a brittle area that can cause a violent rupture or
lead to such a rupture later under rough handling.
3D) SHOCK PREVENTION
Exposed live conductors or other bare metal in the welding circuit, or in
unearthed, electrically-LIVE equipment can fatally shock a person whose body
becomes a conductor. DO NOT STAND, SIT, LIE, LEAN ON, OR TOUCH a wet
surface when welding, without suitable protection.
3E) PROTECTION FOR WEARERS OF ELECTRONIC LIFE SUPPT DEVICES (PACEMAKERS)
Magnetic fields from high currents can affect pacemaker operation. Persons wearing
electronic life support equipment (pacemaker) should consult with their doctor
before going near arc welding, gouging, or spot welding operations.
3F) TO PROTECT AGAINST SHOCK:
Keep body and clothing dry. Never work in damp area without adequate
insulation against electrical shock. Stay on a dry duckboard, or rubber mat
when dampness or sweat can not be avoided. Sweat, sea water, or moisture
between body and an electrically LIVE part - or earthed metal - reduces the
body surface electrical resistance, enabling dangerous and possibly lethal
currents to flow through the body.
1) Earthing the equipment
When arc welding equipment is earthed according to the National
Electrical Code, and the workpiece is earthed, a voltage may exist
between the electrode and any conducting object.
Examples of conducting objects include, but are not limited to, buildings,
electrical tools, work benches, welding power source cases, workpieces,
etc. Never touch the electrode and any metal object unless the welding
power source is off. When installing, connect the frames of each unit such
as welding power source, control, work table, and water circulator to the
building earth.
Conductors must be adequate to carry earth currents safely. Equipment
made electrically LIVE by stray current may shock, possibly fatally. Do NOT
EARTH to electrical conduit, or to a pipe carrying ANY gas or a flammable
liquid such as oil or fuel.
36
No. Description Part No.
PARTS LIST - MIG 135TE
1
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
20
21
22
23
24
25
26
27
28
29
30
31
32
33
35
36
37
38
39
40
41
42
43
44
45
46
47
48
Handle-extension Grip EM21600006
Handle-extension EM33725054
Wire Feeding Motor EM22810001
Complete Thermostat EM04600113
Plastic Handle EM21600021
Complete Fan EM04600055
Torch Grommet On Front Panel EM21690001
Welding Current Switch EM22200006
Potentiometer Knob EM21690017
Yellow Pilot-light Switch EM22200022
Access Panel Hinge EM21690178
Dividing Panel EM33720092
Wire Spool See Accessories
Fixed Spool Holder EM21690011
Spool Holder Retaining Ring EM21690012
Plastic Wire Feeder EM44400001
P.C. Board EM22710043
Cable Clamp EM21605010
Left Access Panel EM33705217
Front Panel EM33710165
Wheels-axle EM55200014
Right-side Upper Panel EM33705216
Rear Panel EM33715063
Wheel EM21625034
Wire Feed Roll Knurled EM33805001
Front Plastic Frame EM21690175
Side Panel Clip EM21690177
Front Plastic Foot EM21610014
Inductance EM44135060
Rectifier EM22400049
Transformer EM44120049
Back Plastic Foot EM21610015
Earth Cable EM43210119
Earth Clamp EM22110005
Red Torch EM23000050
Input Cable, Plug + 13A Fuse EM20220068
Back Plastic Frame EM21690176
Spool Holder Handwheel With Nut EM21800036
Lower Panel EM33700138
Reducer W/Out Gauge EM22905001
Spare Cartridge C02 See Accessories
Hose Clamp EM22915004
Plastic Mask W/Handle EM21905018
Transparent Glass EM21905020
Dark Glass 82x108 BS Din11 EM21905021