Contents 2. Safety/Precautions ............................................................................................... 3 2.1 Safety 2.2 Precautions 3. Points to Check before Use ................................................................................. 5 3.1 Accessories 4. Controls/Functions .............................................................................................. 6 4.1 Front Panel 4.2 Rear Panel 4.3 Remote controller 4.4 Front Display 5. How to Connect .................
Safety/Precautions 1.1 Overview 2.1 Safety This satellite receiver is designed for the reception of free-to-air and encrypted channels. Depending on your location, enjoy the rich choice of up to 10,000 different channels broadcasting a large range of programs: culture, sports, cinema, news, events, etc. This receiver is assembled with highly qualified electronic parts. English Introduction Be sure to read this user's manual before starting the operation of the unit.
2.2 Precautions Points to Check before Use English When installing the unit 3.1 Accessories Install the unit horizontally. An uneven installation may cause the unit to be damaged. Do not put heavy items such as a TV set on the unit. That may damage the unit. The accessories below are included with this receiver: Remote control : 1 User's manual : 1 er's Us Do not leave the unit where the water drops or splashes. Do not put water holding items such as vases on the unit.
.2 Rear Panel Controls/Functions 3 7 6 9 10 2 4 5 8 11 12 13 15 18 4.1 Front Panel 2 No. Name 1 3 4 5 6 7 8 14 16 17 19 Connector Function 1 TV ANT IN IEC 169-2 FEMALE Input from terrestrial antenna 2 RF OUT IEC 169-2 MALE Loop-through output from digital tuner and Output to TV 1 Standby/Power on Indications Lamp : Flashes red light in “Standby” mode and shows no light in “Power ON” mode. 2 Power : Switches the receiver between “Standby” and “Power ON” modes.
4.3 Remote controller 4.3 Remote controller 19 - 20 Double arrow Up/Down : To move to the next or previous page when many pages are available. 2 TV/RADIO : To switch between TV and Radio. 2 21 - 22 Up & Down : To switch channels in 3 MUTE : To turn the sound On/Off. 1 teletext is transmitted. Used for special functions in menu mode. 5 4 6 8 7 12 11 15 9 10 13 14 16 non-menu mode and move the cursor up/down in menu mode.
4.
6.1 Getting Started Operation 3) Antenna Setup 6.1 Getting Started ⊺ Use After your receiver is powered on, proceed with installation as follows : ҫ Note : Enter a 4-Digit password if need arise. The default password is ‘0000’. / and / to move in the menu. ⊻ Press on ‘Dish Setting’. The following window will appear. If you have a motorized dish, press on ‘Motorized Setting’. < Figure 6.1.4> 1) Menu Language Setting ⊹ Turn on your TV and receiver.
6.1 Getting Started 6.1 Getting Started (When the DiSEqC Motor parameter is set as 1.2) 4) Satellite Scan - Limit : If you want to set limits, press Through this function, the receiver searches for all the available channels and saves them in memory. . - Disable Limit : You can disable the East and West limits. ᶀ Auto Scan - Goto Center : Move the dish to the initial 0 position. - Set East / West Limit : Move the dish East or West using Press to set East or West limit. / .
6.1 Getting Started 6.1 Getting Started ᶀ Blind Scan ᶀ Package Identifier (PID) Scan ⊹ Select a transponder. ⊺ Press - Frequency : Select TP frequency ⊺ To change a transponder’s information (Frequency, Symbol Rate), use the NUMERIC buttons. - Polarization : Select Vertical / Horizontal / All. ⊻ To add a new transponder, press the GREEN button.
6.1 Getting Started 6.1 Getting Started ᶀ Manual Scan ᶀ Fast Scan ⊺ For CHs Renumber select ON/OFF ⊻ Press the Red button. ⊹ Select the channel number or frequency you want to search for select the channel number by pressing CH ƌor CH Ɗ on the remote control, or specify a frequency by entering the frequency with the number keys. ⊺ For the Bandwidth choose either 7 MHz or 8 MHz. ⊻ For the Search Type, select All Channel, FTA Only or TV Only.
6.1 Getting Started 6.1 Getting Started 6) Channel List 7) Other Functions of the Remote Control / to navigate between channels until you find the channel you ᶀ Volume Control ⊹ While watching a program, press ᶀ If you know the channel number, you can enter it with the NUMERIC buttons and wait 2 seconds until the channel is changed. ᶀ If you know the channel name or transponder or CAS, you can press channel list or to control the volume.
6.1 Getting Started 6.1 Getting Started ᶀ Multi Picture Display ᶀ SUBTITLE You can press to select the subtitle language of current channel. ᶀ SLEEP You can set the your receiver to turn off after a few minutes. Press timer. - To cancel the sleep timer, please press (Disable, 10, 20, 30, 60, 100, 120 Minutes) to set the sleep until you set time as “0 min”. ᶀ ZOOM You can press to zoom in the video.
6.2 System Setting 6.2 System Setting 1) Time Settings 2) A/V Output Settings This submenu allows you to specify the audio/video output. - GMT Usage : Set this ON for the local time to be determined by adjusting the time difference with the GMT (Greenwich Meantime) according to your location. - Subtitle Language : Set the default subtitle language. - Current Date : If GMT Usage is OFF, you can modify the date by pressing .
6.2 System Setting 6.2 System Setting 3) OSD Settings 5) Security Settings This submenu allows you to set password options and to lock or unlock access to menus (Note : PIN code and password are the same). - Receiver Lock : Set ON to require entering a PIN code at powering on. - Install Lock : Set ON to require entering a PIN code to access the installation menu. - Channel Lock : Set ON to require entering a PIN code to access the channels menu.
6.2 System Setting 6.2 System Setting 6) Database Reset 7) IP Setting - Delete Radio Channels : Erase all radio channels in the database. - Delete Scramble Channels : Erase all scramble channels in the database. - Delete All Channels : Erase all channels. - Factory Set : Erase all channels and restore the factory default settings. If the Network supports DHCP , IP settings can be allocated automatically. If the Network does not support DHCP, the Addresses must enter manually (Static IP).
6.2 System Setting 6.3 Channels 8) Data Transfer 1) Set Favorites - Firmware : Transfer the firmware of a receiver to another receiver. - Channel Data : Transfer the channel data of a receiver to another receiver. This submenu allows you to set up favorite groups of channels. You can select TV or Radio channels in an alternative way by pressing the TV/RADIO button. The receiver supports 16 favorite groups. ⊹ Press on ‘Set Favorites’. The list of groups will be displayed.
6.3 Channels 6.3 Channels 2) Edit Channels 3) Move Channels ⊹ Press on ‘Edit Channels’. The following menu will be displayed. This submenu allows you to move channels. You can select TV or Radio channels in an alternative way by pressing the TV/RADIO button. You can choose a channel list group by pressing the GROUP button. ⊺ Press on the channel that you want to edit. ⊹ Press on ‘Move Channels’. The following menu will be displayed.
6.3 Channels 6.3 Channels 4) Lock Channels 5) Skip Channels This submenu allows you to skip channels. Once a channel is set to be skipped, it will be whenever you navigate channels using / in non-menu mode. You can select TV or Radio channels in an alternative way by pressing the TV/RADIO button. You can choose a channel list group by pressing the GROUP button. ҫ If you set ‘Lock Channel Confirm’ (refer to <6.
6.3 Channels 6.4 Electronic Program Guide 6) Delete Channels 1) EPG ҫ Note : Be careful! If you delete a channel, you will not be able to access it again until you rescan. ⊹ Press on ‘Delete Channels’. The following menu will be displayed. ⊺ Press on the channel that you want to set/unset for deletion; the delete icon will be displayed/removed. ⊻ Press the INFO button to delete all channels in the current list; you will be asked to enter your password.
6.4 Electronic Program Guide 6.5 Games 1) Tetris on ‘Tetris’. The following menu will be displayed. ⊺ You can choose a skill level using / . ⊻ Press to start the game , or press the EXIT button to return to the previous menu. ⊼ Press ⊽ Press ⊾ Press to rotate a block. / to move a block. to drop a block. ⊿ You can see the next block in the top-right small window. ⋀ Press the EXIT button to quit the game.
6.5 Games 6.5 Games 2) Sokoban 3) Snake ⊹ Press on ‘Sokoban’. The following menu will be displayed. ⊺ You can choose a skill level using / . ⊹ Press on ‘Snake’. The following menu will be displayed. ⊺ You can choose a skill level using / . ⊻ Press to start the game , or press the EXIT button to return to the previous menu. ⊼ Press / / / to move. ⊻ Press to start the game , or press the EXIT button to return to the previous menu.
6.6 Storage This submenu allows you to play various MP3 files, view JPG files or download a new software by connecting your USB flash drive. 2) JPG menu ͈ Press / to select a picture. ͉ Press 1) MP3 menu ͈ Select the MP3 file you want to play back by using / , in the file list. ͉ Press the EXIT button to hide the file list. You can then select an option using .
6.6 Storage 6.6 Storage - Format Disk : You can format the usb devices. 4) Disk Manager - Testing USB Speed : USB speed test. ҫ Note : If External SATA is connected, External SATA can be captured in “volume0”. Otherwise, one of other disks can be captured in “volume0” - Timeshift Rec Time : You can change default timeshift recording time. - Disk Information : Choose the Hard disk volume or usb device with USB hub.
6.7 System Information 5) File manager You can check the current information about your receiver such as receiver model name, S/W (software) version, H/W (hardware) version, manufacturing date, etc. ͈ Press YELLOW button for connect PC. ͉ Press button after input IP address of PC. ͊ Press button after choose target. ҫ Note : This information is useful to download new software and/or repair the receiver. ҫNote : Have to run PC tool before connect PC.
6.8 Common Interface 6.9 Conditional Access System 1) Card Initializing ҫ Note : Without the Smart Card, you can watch only Free-To-Air programs. ͈ Insert the Smart Card into the receiver’s slot designed for it. ͉ The message ‘Smart Card Initializing’ will appear on the screen. ͊ After the message ‘Smart Card Initializing’ has disappeared, you will be able to watch the channels offered by the service provider.
6.9 Conditional Access System 6.10 PVR 2) The Status of the Smart Card 1) File List / keys in ͉ Proceed with further instructions displayed on the screen to check more detailed information depending on the Smart Card in use. ҫ Note : Further detailed information is not mentioned in this manual since the information depends on the Smart Card in use. ᶀ File Playback ⊹ Press to show the file list. Select the file you want to play back by using , . ⊺ Press .
6.10 PVR 6.10 PVR ᶀ Edit Menu 2) Trick Mode . The pop- You can operate the trick mode while you are playing the recording files. These functions are available in playback mode or time-shift mode powerfully. Select the item that you want to edit, and set its parameters as desired ⊹ Normal Mode : Press ⊺ Lock Mode : Press ͊ Delete Mode : Press on the file that you can see the preview of a selected file. on the file that you want to lock/unlock. on the file that you want to delete.
6.10 PVR 6.10 PVR ᶀ RWD(Rewind) ᶀ Bookmark to adjusting the playing speed. - RED : Press this button and red small triangle cursor will be placed at that position. If you want to delete the bookmarked position, press a this button once more when red small triangle cursor appear. The speed will change to x2, x4, x8. ᶀ Slow(1/2x, 1/4x) When playing the file, you can press 6.10.7> to adjusting the playing speed.
6.10 PVR 6.10 PVR 4) Instant Recording 5) Timer Recording . If you then press , a time-banner ⊺ Press once more. The following picture shows that you can select item when you record a current channel. This function is availabe when usb device is connected. You can choose a channel to record the Program Guide menu by using . (Refer to 6.4 Electric Program Guide, 2)Timer) - Channel : It shows a current channel. - Name : It shows a current recording name.
Troubleshooting Specifications Problem Possible causes Remedy The LED light on the front The AC power cord is disconnected. panel does not light. No Picture or sound. System capabilities satellite LNB/Tuner input Connect the power cord properly into the power socket. Fully DVB compliant Connector Frequency range Signal level LNB supply LNB switch control DiSEqC Front end Symbol rate IEC 169-24, female 950MHz ~ 2150MHz -65dBm ~ -25dBm DC 13/18V, max 400mA 22KHz Ver 1.0/1.1/1.
Remote control USB Power supply Rear Panel connectors Code Operating condition USB Supply(Front/Rear) Power consumption Supply voltage Passive standby Supply frequency TV SCART VCR SCART Video Audio L/R Component(Y/Pb/Pr) Serial data Digital tuner input Loop-through Digital tuner Terrestrial ant input Terrestrial ant output S/PDIF HDMI USB SATA LAN Physical Specification Size (W X H X D) Weight (Net) NEC-IR up to 7 Meter DC 5V Max 500mA max 50W 100V ~ 250V <1W 50Hz ~ 60Hz CVBS Video output, Loop-throu
