Clarion Co., Ltd. Published by Service Dept. 50 Kamitoda, Toda-shi, Saitama 335-8511 Japan Service Dept.: 5-66 Azuma , Kitamoto-shi, Saitama 364-0007 Japan Tel: +81-48-541-2335 / 2432 FAX: +81-48-541-2703 298-6351-00 Mar.2006 Printed in Japan Service Manual DVD Multmedia Station with Touch Panel Controller Model (QC-6823B-A) (NTSC/ Region No. "1") Model (QC-6823K-A) (PAL/ Region No. "3") Model (QC-6823K-B) (NTSC/ Region No. "3") Model (QC-6823K-C) (PAL/ Region No.
Input section Video input: Audio input: 1.0V+0.2/-0.2Vp-p (input impedance 75 ohm) 130mV+60/-60mVrms(High) 600mV+80/-80mVrms(Mid) 840mV+100/-100mVrms(Low) (input impedance 10k ohm or greater) * Video output section Video output: 1.0V+0.2/-0.
CAUTIONS Use of controls,adjustment or performance of procedures other than those specified herein,may result in hazardous radiation exposure. The compact disc player should not be adjusted or repaired by anyone except properly qualified service personnel. QC-6823B-A To engineers in charge of repair or inspection of our products. Before repair or inspection, make sure to follow the instructions so that customers and Engineers in charge of repair or inspection can avoid suffering any risk or injury. 1.
ERROR DISPLAYS If an error occurs,one of the following displays is displayed.Take the measures described below to eliminate the problem. Cause A CD is caught inside the CD deck and is not ejected. A CD cannot be played due to scratches,etc. A CD is loaded upside-down inside the CD deck and does not play. A CD inside the CD changer is not loaded. A CD inside the CD changer cannot be played due to scratches,etc. A CD inside the CD changer cannot be played because it is loaded upside-down.
WIRE CONNECTION Yellow Radio antenna jack Yellow BACK UP (+12V main power) Black Ground TV tuner input terminal or DVD changer input terminal Purple Rear r ight + Purple/Black CeNET terminal Red Gray Rear r ight +12V accessory Front right + Gray/Black Front right White Optical output connector No. 1 3 5 7 9 11 13 15 Description SP R/L(+) SP F/L(-) SP F/L(+) SP F/R(+) SP F/R(-) SP R/R(+) SP R/R(-) BACK UP J601 No.
BLOCK DIAGRAM Main unit section VRX765VD VRX766VD -6-
ADJUSTMENTS *Refer to the printed circut board(47,50 or 51 pages)for an adjustment point and VR. *The NTSC (K-A:PAL)composite output signal of the signal generators of adjustment is performed with the following output.Video input of visual mode. A image signal: 714mV A synchronized signal: 286mV Sub PWB section 1. Confirm the power supply voltage Input signal: 10-steps wave Measurement is performed by composite screen display.It measures by digitalbolt meter and DIMMER is 100%. 1-1.
9. Free run frequency adjustment Input signal: 10-steps wave Measurement is performed by composite screen display. It measures by frequency counter and DIMMER is 100%. 9-1.Adjust VR941 so that the frequency of TP949 will become to 15.734kHz+10/-10Hz. *TP804 is made to short-circuit to GND. It checks that the voltage of TP951 is 1.61+0.20/-0.20V at this time. And checks that the voltage of TP952 is same. Main PWB section 19.
20-3-3.Set SG output to 55dBuV.(FM) 20-3-4.Click [Adj,LO] of "FM S-Meter".(Wait until the value stops.) 20-3-5.Click [Check].If the display is not within +/-0.5dBuV of ANT-output level of SG, readjust with "MODON"(22.5kHz 400Hz). Slide mechanism section 23 Horizontally position Calibration jig is used in order to memorize a horizontal level position. Please refer to an attached figure A. It is made to memorize horizontally among a figure in the position of points.
EXPLANATION OF IC + OSC Dead time Control R Q S High side Driver Low side Driver Over+ 16 GND 9 17 + Over - 15 OSC 10 Soft S 14 Boot strap Thermal shut down + Error Amp in- 13 26 1,2,22,23,24,25 3,4,5,6 P GND Vout VDD Error Amp out 12 7 V GH 8 VB CONTROL V GL 21 R/C (H-ON) 18 20 Vboot DC to DC Converter 11 Vref MD1424R 19 VCC 051-3924-90 pin 6: PLL CTL 4 : IN : PLL multiply select. pin 7: PLL CTL 3 : IN : PLL multiply select. pin 8: PLL CTL 2 : IN : PLL multiply select.
pin 74: Memo OE_N : O : Pattern Memory interface. Output enable. pin140: VDD : - : Digital power supply. pin 75: Memo D 15 :I/O: Pattern Memory interface. Data I/O. pin141: X IN : IN : Crystal connection. pin 76: Memo D 7 :I/O: Pattern Memory interface. Data I/O. pin142: X OUT : O : Crystal connection. pin 77: Memo D 14 :I/O: Pattern Memory interface. Data I/O. pin143: VSS : - : Digital ground. pin 78: Memo D 6 :I/O: Pattern Memory interface. Data I/O. pin144: NC : - : Not in use.
052-7078-01 uPD703276YGJ-512UENA System Controller pin 53: IRI : IN : The remote control signal input. pin 54: NU : IN : Not in use. pin 55: NU : IN : Not in use. music. pin 56: NU : IN : Not in use. iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries. pin 57: NU : IN : Not in use. pin 58: OSD RST : O : The reset pulse output for the on screen display IC. pin 59: TP RX : IN : The serial data input from the touch panel micro computer.
pin112: DSP RST : O : Reset pulse output to the DSP IC. pin 10: A 20 pin113: DSP INIT : IN : The initial finished signal input from the Radio-Audio-DSP. pin 11: WE : IN : Write enable signal input. pin 12: RESET : IN : Reset signal input. pin114: SAMPLE : IN : Not in use. pin 13: NU : - : Not in use. pin115: NU : - : Not in use. pin 14: WP/ACC : IN : The write protection signal input / The acceleration signal input. pin116: AM/FM 8V ON : O : AM/FM 8V ON signal output.
EXPLODED VIEW : PARTS LIST Main section 104 98 43 96 7 10 99 21 97 47 26 30 21 100 39 31 52 103 55 6 20 36 4 45 43 23 97 18 40 101 104 102 49 39 33 49 50 5 32 3 51 16 24 9 38 76 19 29 38 11 40 84 51 53 17 88 59 8 78 48 38 38 93 75 15 58 61 87 13 67 60 79 69 62 70 27 89 63 80 71 92 73 91 61 41 54 81 74 82 72 90 44 66 85 41 77 68 35 41 14 64 37 83 38 94 65 86 41 44 34 46 56 56 28 12 2 56 1 25 56 57 22 38 42 VRX765VD
Note)Some parts depend on each model.The model name is specified in the descripion . (B-A;QC-6823B-A, K-A;PF-QC-6823K-A, K-B;QC-6823K-B , K-C;QC-6823K-C) NO. Q'TY NO. DCP-558-600 DCP-ASSY(B-A) DCP-559-800 DCP-ASSY(K-A,K-B,K-C) 1 49 781-1722-50 PLATE SCREW(M1.7x2.2) 4 2 ----------- 1 50 781-1750-50 SCREW(phi1.7x2.2) 4 3 335-7790-00 TOP-CVR 1 51 781-2002-50 PLATE SCREW(M2.
NO. Q'TY NO. PART NO. 99 074-2001-80 OUTLET SOCKET PART NO. DESCRIPTION 1 102 074-2001-64 OUTLET SOCKET(14P) DESCRIPTION Q'TY 1 100 076-0568-00 PLUG(2P) 1 103 074-2001-70 OUTLET SOCKET(20P) 1 101 074-1189-85 OUTLET SOCKET(35P) 1 104 ----------- LCD PWB Inner Escutcheon section 6 8 15 23 16 16 9 1 16 11 21 3 14 12 26 27 7 28 25 29 27 17 1 27 18 24 26 4 10 17 1 20 5 14 22 17 13 19 2 NO. PART NO. DESCRIPTION Q'TY NO. 1 ----------- 2 3 PART NO.
DCP section 23 20 3 15 22 21 13 16 18 24 22 22 22 17 10 1 11 4 12 5 7 6 9 12 14 19 8 2 NO. PART NO. DESCRIPTION Q'TY NO. PART NO.
ELECTRICAL PARTS LIST Main PWB(B1) section Note)Some parts depend on each model.The model name is specified in the descripion . (B-A;QC-6823B-A, K-A;PF-QC-6823K-A, K-B;QC-6823K-B , K-C;QC-6823K-C) Note) Several different parts of the same reference number are alternative parts. One of those parts is used in the set. REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No.
REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION C345 C401 C402 C403 C404 C405 C406 C407 C408 C409 C410 C411 C412 C413 C414 C415 C416 C417 C418 C421 C422 C423 C424 C425 C426 C427 C428 C429 C430 C431 C432 C433 C434 C435 C436 C437 C438 C439 C441 C450 C451 C452 C454 C455 C456 C457 C458 C459 C460 C461 C462 C463 C464 C465 C466 C467 C468 C469 C470 C471 C472 C473 C474 C475 C476 C477 C478 C479 C480 C484 C485 C486 C487 C488 470pF K 16V 0.1uF 6.3V 10uF 6.3V 10uF 16V 0.
REF No. PART No.
REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No.
REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION R571 R572 R573 R605 R606 R608 R609 R610 R611 R612 R613 R614 R615 R616 R617 R618 R619 R620 R621 R622 R623 R624 R625 R626 R627 R628 R629 1/10W 10k ohm 1/10W 100 ohm 1/10W 100 ohm 1/10W 10k ohm 1/10W 47k ohm 1/10W 10k ohm 1/4W 1.2k ohm 1/10W 10 ohm 1/10W 10k ohm 1/4W 1.2k ohm 1/4W 1.2k ohm 1/10W 10k ohm 1/10W 10k ohm 1/10W 10k ohm F 1/10W 10k ohm 1/4W 1.5k ohm 1/4W 1.
LCD PWB(B3) section REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION C701 C703 C704 C705 C706 C707 C708 C709 C710 C711 C712 C713 C714 C715 C716 C801 C802 C803 C804 C805 C806 C807 C808 C809 C810 C811 C812 C813 C814 C815 C816 C817 C818 C819 C820 C821 C822 C823 C824 C825 C826 C827 C828 C829 C830 C831 C832 C833 C834 C835 C836 C837 C838 C839 C840 C841 C842 C843 C844 C845 C846 C847 C848 C850 C851 C852 C853 C854 C855 C856 C857 C858 0.1uF 16V 0.1uF 10V 47uF M TAN 16V 0.
REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. R702 R705 R706 R707 R709 R710 R711 R712 R713 R801 R802 R803 R804 R805 R806 R807 R808 R809 R810 R811 R812 R813 R814 R815 R816 R817 R818 R819 R820 R821 R822 R823 R824 R825 R826 R827 R828 R829 R830 R831 R832 R833 R834 R835 1/10W 22k ohm 1/10W 470 ohm 1/10W 470 ohm 1/10W 680 ohm 1/10W 1M ohm 1/10W 3.3k ohm 1/10W 47k ohm 1/10W 220 ohm 1/10W 220 ohm 1/10W 4.
CIRCUIT DIAGRAM Main PWB 1/7 section (B1) TO MAIN 6/7 PAGE 30 TO MAIN 2/7 PAGE 26 TO MAIN 2/7 PAGE 26 TO MAIN 3/7 PAGE 27 TO MAIN 7/7 PAGE 31 TO MAIN 6/7 PAGE 30 TO MAIN 2/7 PAGE 26 TO MAIN 7/7 PAGE 31 - 25 - VRX765VD VRX766VD
CIRCUIT DIAGRAM Main PWB 2/7 section(ޓB1) TO MAIN 7/7 PAGE 31 TO MAIN 3/7 PAGE 27 TO MAIN 1/7 PAGE 25 TO MAIN 1/7 PAGE 25 4 Red Gray 3 P201 No. 1 2 3 4 5 6 7 8 9 10 TO MAIN 1/7 PAGE 25 Description Description No.
CIRCUIT DIAGRAM Main PWB 3/7 section (B1) TO MAIN 7/7 PAGE 31 Optical output TO MAIN 6/7 PAGE 30 To DVD mechanism To CN701 To 039-2793-00 FPC Page 33 TO MAIN 1/7 PAGE 25 To CN401 TO MAIN 5/7 PAGE 29 039-2792-00 TV input Yellow TO MAIN 7/7 PAGE 31 855-5436-50 Black TO MAIN 6/7 PAGE 30 TO MAIN 2/7 PAGE 26 - 27 - VRX765VD VRX766VD TO MAIN 6/7 PAGE 30 TO MAIN 4/7 PAGE 28
CIRCUIT DIAGRAM Main PWB 4/7 section(ޓB1) TO MAIN 7/7 PAGE 31 TO MAIN 5/7 PAGE 29 TO MAIN 6/7 PAGE 30 TO MAIN 3/7 PAGE 27 - 28 - VRX765VD VRX766VD
Main PWB 5/7 section (B1) TO MAIN 7/7 PAGE 31 TO MAIN 4/7 PAGE 28 TO MAIN 6/7 PAGE 30 TO MAIN 3/7 PAGE 27 - 29 - VRX765VD VRX766VD
Main PWB 6/7 section(ޓB1) TO J503 OF SUB PWB PAGE 32 TO MAIN 1/7 PAGE 25 TO MAIN 1/7 PAGE 25 TO MAIN 2/7 PAGE 26 TO MAIN 3/7 PAGE 27 TO MAIN 3/7 PAGE 27 TO MAIN 3/7 PAGE 27 TO MAIN 7/7 PAGE 34 TO MAIN 4/7 PAGE 28 TO MAIN 7/7 PAGE 34 TO J1101 OF SWITCH PWB PAGE 41 TO MAIN 5/7 PAGE 29 TO MAIN 7/7 PAGE 34 - 30 - VRX765VD VRX766VD (K-A,B,C) (B-A,K-B) (B-A) (K-A,K-C)
Main PWB 7/7 section (B1) TO MAIN 2/7 PAGE 26 No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 FAN MOTOR Description SP R/L(+) SP R/L(-) SP F/L(-) PHONE MUTE SP F/L(+) ACC SP F/R(+) AUTO ANT SP F/R(-) REMOTE SP R/R(+) ILLUMI SP R/R(-) PARKING BRAKE BACK UP GND TO MAIN 6/7 PAGE 30 TO MAIN 2/7 PAGE 26 TO J551 OF SUB PWB PAGE 32 TO MAIN 6/7 PAGE 30 TO MAIN 3/7 PAGE 27 TO MAIN 4/7 PAGE 28 TO MAIN 5/7 PAGE 29 TO MAIN 3/7 PAGE 27 TO MAIN 1/7 PAGE 25 No. 1 2 3 4 5 6 7 8 9 10 No.
Sub PWB section(ޓB2) TO FPC FPC 039-2793-00 PAGE 33 TO J602 OF MAIN PWB PAGE 31 TO J502 OF MAIN PWB PAGE 30 - 32 - VRX765VD VRX766VD
LCD PWB 1/3 section (B3) TO J502 OF SUB PWB PAGE 32 TO J303 OF MAIN PWB 3/7 PAGE 27 TO LCD 2/3 PAGE 34 (ACC-ON,ILL-OFF,VISUAL MODE-10STEP) - 33 - VRX765VD VRX766VD
TO J901 OF LCD PWB 3/3 PAGE 35 LCD PWB 2/3 section(ޓB3) TO LCD 1/3 PAGE 33 - 34 - VRX765VD VRX766VD
TO J801 OF LCD PWB 2/3 PAGE 34 FROM INDICATOR 379-0468-00 LCD PWB 3/3 section (B3) BACK LIGHT 63KHZ BACK LIGHT FROM INDICATOR 379-0468-00 FROM TOUCH PANEL 013-9710-00 - 35 - VRX765VD VRX766VD
Q P O N M L K J I H G F E J601 J604 (CeNET) 1 A Description GND BACK UP L-CH(+) N.C. N.C. BUS(+) R-CH(+) R-CH(-) SYS-ACC BUS(-) L-CH(-) ILLUMI N.C. 2 13 16 1 6 5 4 3 10 9 8 7 12 11 15 14 12 10 8 6 4 2 13 11 9 7 5 3 1 No. 1 3 5 7 9 11 13 15 Description SP R/L(+) SP F/L(-) SP F/L(+) SP F/R(+) SP F/R(-) SP R/R(+) SP R/R(-) BACK UP No. 2 4 6 8 10 12 14 16 Description SP R/L(-) PHONE MUTE ACC AUTO ANT REMOTE ILLUMI PARKING BRAKE GND YELLOW J603 No.
B C D E F G H I J K L M N O P Q R S 0 0 A Main PWB(B1) section Optical output connector No. 2 4 6 8 10 12 14 16 J601 Description SP R/L(-) PHONE MUTE ACC AUTO ANT REMOTE ILLUMI PARKING BRAKE GND J604 (CeNET) 1 3 5 7 9 11 13 15 2 4 6 8 10 12 14 16 11 7 8 9 3 4 5 13 1 12 10 6 2 No. 1 2 3 4 5 6 7 8 9 10 11 12 13 Description GND BACK UP L-CH(+) N.C. N.C. BUS(+) R-CH(+) R-CH(-) SYS-ACC BUS(-) L-CH(-) ILLUMI N.C.
R Q P O N M L K J I H G F E D C B A J I H G F E D C B A PRINTED WIRING BOARD 0 0 S 6 6 5 5 4 4 3 3 2 2 1 1 LCD PWB(B3) section 10 10 9 9 8 8 7 7 To TFT INDICATOR 379-0468-00 COMPONENT SIDE 12 12 11 11 To TOUCH PANEL 013-9710-00 Caution: COMPONENT SIDE: Parts on the component side seen from the component side are indicated. S R Q P 13 13 Note)This PWB has the four-layer boaud.
B C D E F G H I J K L M N O P Q R S LCD PWB(B3) section 0 0 A 1 To J303 of Main PWB Page 36 1 To J502 of Sub PWB Page 40 2 2 FPC 039-2793-00 To SLIDE MECHANISM 948-0692-05 4 5 6 6 5 4 3 To SLIDE MECHANISM 948-0692-05 3 FLAT WIRE 816-2650-00 To INDICATOR 379-5006-00 7 8 9 10 10 9 8 7 FPC 039-2509-00 11 12 12 11 SOLDER SIDE A B C D - 39 - F G H VRX765VD VRX766VD J K L M N O P Q R 13 13 Caution: SOLDER SIDE: Parts on the solder side seen from
SUB PWB(B2) section FPC 039-2793-00 FLAT WIRE 816-3013-50 To J702 of LCD PWB Page 39 To J502 of Main PWB Page 36 To J602 of Main PWB Page 36 COMPONENT SIDE COMPONENT SIDE SOLDER SIDE SOLDER SIDE Caution: COMPONENT SIDE: Parts on the component side seen from the component side are indicated. SOLDER SIDE: Parts on the solder side seen from the solder side are indicated.
CIRCUIT DIAGRAM Switch PWB section (B4) TO J501 OF MAIN PWB PAGE 30 - 41 - VRX765VD VRX766VD
PRINTED WIRING BOARD Switch PWB(B4) section COMPONENT SIDE SOLDER SIDE To J501 of Main PWB Page 37 Caution: COMPONENT SIDE: Parts on the component side seen from the component side are indicated. SOLDER SIDE: Parts on the solder side seen from the solder side are indicated.
Clarion Co., Ltd. Published by Service Dept. Feb.2006 50 Kamitoda, Toda-shi, Saitama 335-8511 Japan Service Dept.: 5-66 Azuma , Kitamoto-shi, Saitama 364-0007 Japan Tel: +81-48-541-2335 / 2432 FAX: +81-48-541-2703 Printed in Japan Service Manual DVD Mechanism Model NOTES * * * 658-0237-08 929-2504-00 C0GBY0000012 Coil & Motor Driver The FPC pattern of a spare suspension assembly is short-circuited to prevent destruction with static electricity.
658-0245-01 C1AB00001622 Terminal Description pin 1: VDD IO System Controller (NDV8602VWA) pin 65: /DQM 3 : O : SDRAM data byte enable (0V) pin 66: /CS 1 : - : Not used pin 67: VSS IO : - : I/O pad ground (0V) : - : I/O pad power (3.3V) pin 68: S/PDIF : O : S/PDIF digital audio output (1.3V) : - : Core ground (0V) pin 2: MD 10 :I/O: SDRAM data bus (0V) pin 69: VSS pin 3: MD 11 :I/O: SDRAM data bus (0.6V) pin 70: A IN : IN : Digital audio input for digital micro (3.
pin130: V I/O 3 : - : Not used pin196: VDD IO : - : I/O pad power (3.4V) pin131: V I/O 2 : - : Not used pin197: DAC CS 1 : O : DAC output select 1 (3.4V) pin132: VSS IO : - : I/O pad ground (0V) pin198: NINT CPPM : - : Not used pin133: V I/O 1 : - : Not used pin199: CPPMCS : - : Not used pin134: V I/O 0 : - : Not used pin200: XI06 : - : Not used pin135: VDD : - : Core power (1.
658-0244-03 C3ABPJ000072 Terminal Description pin 1: VDD 0 512K x 32 x 4 banks SDRAM (MT48LC2M32B2TG) : - : Positive supply voltage. pin 2: D :I/O: Data input/output. pin 3: VDD : - : Positive supply voltage. pin 4: D 1 :I/O: Data input/output. pin 5: D 2 :I/O: Data input/output. pin 6: VSS : - : Negative supply voltage. pin 7: D 3 :I/O: Data input/output. pin 8: D 4 :I/O: Data input/output. pin 9: VDD : - : Positive supply voltage. pin 10: D 5 :I/O: Data input/output.
DISASSEMBLY Remove SUSPENSION-ASSY Remove Servo-PWB 1. Solder two points of FPC to prevent destruction with static electricity. Servo PWB side 1. Remove EARTH-SPRING and OFFSET-SPRINGS. Earth-Spring Solder points Pick-up side Offset-Spring 2. Remove FCPs from PICK-UP-UNIT and SENSOR-FPCASSY. 3. Remove three SCREWS. 4. Remove the connector of LOADING-MOTOR-ASSY. FPC from Pick-Up-Unit Screw Screw Offset-Spring Suspension-ASSY 2. Remove LOADING-GEAR(1). 3. Move CLAMP-RACK to GEAR side(Point "A").
Remove LOADING-GEAR/LOADING-MOTOR [NOTE] When assembling, set the dot marks of LOCK-GEAR(1) and MAIN-CHASSIS. 1. Remove six LOADING-GEARS in the following order. (1) > (4) > (3) > (2) > (5) > (6) 2. Remove two SCREWS,and remove LOADING-MOTORASSY. 㪛㫆㫋㩷㫄㪸㫉㫂 Loading-Motor-ASSY 㪤㪸㫀㫅㩷㪺㪿㪸㫊㫊㫀㫊 Loading-Gear(1) Gear(1) Loading-Gear(6) Loading-Gear(5) Suspension-Lock-Lever(L) Screw Loading-Gear(2) Loading-Gear(3) Loading-Gear(4) 3.
EXPLODED VIEW / PARTS LIST 3 4 GREASE 2 6 33 5 7 34 GREASE 12 GREASE 11 9-1 GREASE GREASE 28 29 30 8 25 31 21 22 GREASE 9 35 18 7 8 23 19 GREASE 32 15 17 26 16 35 24 GREASE 14 8 26 20 13 35 10 27 35 10 GREASE : MOLYKOTE PG-641 10 1 NO. PART NO. DESCRIPTION Q'TY NO. 1 ----------- Servo PWB 2 3 4 5 PART NO.
ELECTRICAL PARTS LIST Servo PWB(BM1) section REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION C101 C102 C103 C104 C113 C114 C115 C116 C117 C121 C122 C124 C125 C126 C127 C128 C129 C131 C132 C133 C134 C136 C137 C141 C142 C143 C144 C145 C151 C152 C153 C154 C201 C202 C203 C204 C205 C206 C207 C208 C211 C213 C214 C215 C216 C221 C222 C223 C224 C225 C226 C231 C232 C234 C235 C236 C237 C239 C240 C241 C242 C243 C244 C245 C246 C247 C248 50V560pF 0.1uF 10WV 50V0.001uF 50V0.
REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No.
REF No. PART No. DESCRIPTION REF No. PART No. R718 R721 R722 R723 1/16W 100 ohm 1/16W 100 ohm 1/16W 100 ohm 1/16W 100 ohm R724 R725 SW301 033-1011-15 033-1011-15 033-1011-15 033-1011-15 929-2504-00 DESCRIPTION 033-1011-15 1/16W 100 ohm 033-1011-15 1/16W 100 ohm 658-0244-13 Switch K0L1BA000104 - M10 - REF No. PART No.
BLOCK DIAGRAM IC101 RF AMP 57 VIN1 58 VIN2 59 VIN3 60 VIN4 Q152 DVD LDIN 7 16 28 22 24 Optical Pich up Assy 26 29 21 STOIO SCK SEN STANDBY DVD MON CD F1 CD F2 53 VIN9 54 VIN10 DFLTOP 31 DFLTON 30 111 ARF 110 NARF 2 LPCO1 FE OUT 22 F BAL 7 117 AD0 66 FBAL TE OUT 18 T BAL 6 118 AD1 65 TBAL AS OUT RFENV J LINE OFTR BDO HDTYPE TEST SG 62 VIN11 6 VIN12 Q151 CD LD+ 4 LPCO2 CD MON 3 11 6 49 VIN5 50 VIN6 CD E CD F 12 IC652 9 IC501 MEDIAMATICS DVD IC201 DVD SERVO/DSP 1 LPC1 3 LPC2 2
PRINTED WIRING BOARD Servo PWB(BM1) section IC Q 501 621 641 631 431 652 561 275 651 301 321 311 411 154 60 153 101 321 151 152 252 When you release suspension assy, please solder two points of FPC to prevent destruction with static electricity.
CIRCUIT DIAGRAM Servo PWB(BM1) section 1/2 To 2/2 (g) To Sensor FPC Assy To Loading Motor To Suspension Assy To 2/2 (h) To 2/2 (i) To 2/2 (k) To 2/2 (l) To 2/2 (m) To 2/2 (n) To 2/2 (o) To 2/2 (p) To 2/2 (a) To 2/2 (b) To 2/2 (c) To 2/2 (d) To 2/2 (e) No Connection To 2/2 (f) To Optical Pick Up - M13 - 929-2504-00
Servo PWB(BM1) section 2/2 To 12-pin connector of Main unit C0FBBK000048 To 1/2 (g) To 30-pin connector of Main unit To 1/2 (a) To 1/2 (h) To 1/2 (k) To 1/2 (l) To 1/2 (o) To 1/2 (i) To 1/2 (p) To 1/2 (m) C1AB00001622 To 1/2 (n) To 1/2 (c) To 1/2 (e) To 1/2 (f) To 1/2 (b) To 1/2 (d) 929-2504-00 - M14 -
