Owner’s manual & Installation manual Mode d’emploi et manuel d’installation Manual de instrucciones y de instalación VRX755VD AM/FM DVD VIDEO / VIDEO CD / CD / MP3 PLAYER / CD CHANGER CONTROLLER WITH 7" LC DISPLAY CONTRÔLEUR DE RADIO AM/FM/LECTEUR DVD VIDÉO /CD VIDÉO/CD/MP3/CHANGEUR CD AVEC AFFICHEUR À CRISTAUX LIQUIDES DE 7 POUCESl CONTROLADOR DE RADIO DE AM/FM, REPRODUCTOR DE DISCOS DVD/VIDEODISCOS CD/CD/MP3/CAMBIADOR DE DISCOS CD CON VISUALIZADOR DE CRISTAL LÍQUIDO DE 7" Clarion Co., Ltd.
English Owner’s manual Thank you for purchasing the Clarion VRX755VD. ∗ This owner’s manual is for the VRX755VD. ∗ Please read this owner’s manual in its entirety before operating this equipment. ∗ After reading this manual, be sure to keep it in a handy place (e.g., glove compartment). ∗ Check the contents of the enclosed warranty card and keep it carefully with this manual. ∗ This manual includes the operating procedures of the CD changer, DVD changer, TV tuner, SIRIUS, iPod control, 2-ZONE control, 5.
The Color LCD Display and the Information Panel on the main unit show the following displays, providing information about the mode and functions operated. : Preset channel indication Disc number indication ∗The disc numbers corresponding to the discs in the DVD or CD changer light. : SIRIUS indication 1.
[FRONT OPEN] [SENSOR] Español [DISP] [ISR] [TILT] button Names of Buttons Note: • Be sure to read this chapter referring to the front diagrams of chapter “3. CONTROLS” on page 5 (unfold). [DIRECT] [OPEN] [ADJ] With the Front panel open / Avec le panneau avant ouvert / Con el panel frontal abierto [ADJ] button [Q] button • Use this button to increase/decrease the volume. • Shows the ADJUST mode menu to change the settings when the liquid crystal panel is open.
[FRONT OPEN] [SENSOR] Español [DISP] [ISR] [TILT] button Names of Buttons Note: • Be sure to read this chapter referring to the front diagrams of chapter “3. CONTROLS” on page 5 (unfold). [DIRECT] [OPEN] [ADJ] With the Front panel open / Avec le panneau avant ouvert / Con el panel frontal abierto [ADJ] button [Q] button • Use this button to increase/decrease the volume. • Shows the ADJUST mode menu to change the settings when the liquid crystal panel is open.
The Color LCD Display and the Information Panel on the main unit show the following displays, providing information about the mode and functions operated. : Preset channel indication Disc number indication ∗The disc numbers corresponding to the discs in the DVD or CD changer light. : SIRIUS indication 1.
English Color LCD Display Mode name Owner’s manual •Radio mode : FM1 98.1MHz Pch 1 (band/frequency/preset No.) •SIRIUS mode : SR1 100ch Pch 1 (band/channel/preset No.) •DVD changer mode: D2 T02 C002 01:08:20 (disc No./title No./chapter No./ playback time) •DVD video mode : T01 C003 00:08:20 (title No./chapter No./playback time) •Video CD mode : T01 00:01:18 (track No./playback time) •MP-3 mode : F001 T001 00:04:07 (folderNo./track No./playback time) •CD mode : T 02 04 : 07 (track No.
English 6. OUTLINE OF BUTTON AND TOUCHKEY OPERATION Owner’s manual ∗2 ∗1 Engine ON position System check The CeNET format utilized on this unit is provided with a system check function. The operation panel’s system check menu is displayed under the following conditions: • When power is first turned on after initial installation. • When an external device is connected or disconnected. • When batteries are changed or otherwise when power is disconnected. • When reset button is pressed.
English (Radio mode screen) Owner’s manual (Next page) (List screen) ∗3 (KEY PAD screen) ∗5 (Title input screen) ∗4 1 0 7 9 ENT ∗6 ∗7 Notes: ∗1: The operation button is [OPEN] button in the description of operation per mode. ∗2: External equipment not connected with CeNET is not displayed. ∗3: The operation key is [SRCH] key in the description of operation per mode. ∗4: This shows a KEY PAD selection example in the radio mode when 107.9 MHz is selected.
English (Radio mode screen) Owner’s manual (SOURCE menu) ∗8 ∗9 ∗11 (DVD mode screen) ∗10 (SUB menu) Notes: ∗8: The SOURCE menu screen displays icons for components connected to the main unit. The icons serve as touch keys for selecting play modes. ∗9: Pressing the [SOURCE] button changes to the following play modes. ∗10: Screen during DVD mode when automobile is moving. ∗11: When displaying images in DVD mode, touching the screen surface will cause the menu screen to be displayed.
English Owner’s manual (Next page) (ADJUST mode menu) (DVD SETUP menu) (MONITOR menu) MONI ADJ PARENRTAL LEBEL VRX755VD 13
English Owner’s manual (ADJUST mode menu) When a 5.
English Owner’s manual (AUDIO mode menu) (AUDIO EXT.
English 7. REMOTE CONTROL Remote control unit Owner’s manual Signal transmitter Operating range: 30˚ in all directions [BAND] [MUTE] [SOURCE] [VOLUME] [P.TIME] [0-9] [DISP] [DISC SEL] [ ],[ ] [SEARCH MODE] [MENU] [RTN] [DVD TITLE] [SET UP] [ENT] [ ],[ ] [ISR] [2-ZONE] [RPT] [SCN] [RDM] [AUDIO] [PBC] [SLOW] [ANGLE] [SUB TITLE] Inserting the Batteries 1.Turn the remote control unit over, then slide the rear cover in the direction of the arrow. 2.Insert the AA (SUM-3, IECR-6/1.
When 2-ZONE function is OFF: ● Shared modes ● DVD player mode [BAND] button • Press to return to the first chapter in DVD video mode. • Press to return to the first track in CD/MP-3 mode or video CD mode with the PBC function turned off. [SOURCE] button [P.TIME] button • Press and hold this button for 1 second or longer to turn on or off the power. Power on/ off, switches among radio, TV, etc. [ [VOLUME] button • Increases and decreases volume. [MUTE] button • Turns mute on and off.
English Functions of Remote Control Unit Buttons Owner’s manual [SCAN] button [RDM] button • Press to perform chapter scans in DVD video mode and track scans in CD mode. Press to perform track scan and hold down to perform folder in MP-3 mode. • Press to play tracks at random and hold down to play folders at random. [RPT] button ● DVD changer mode [BAND] button • Press to perform chapter repeat in DVD video mode and track repeat in CD mode.
Removing the DCP 1. Press the [SOURCE] button for 1 second or longer to turn off the power. CAUTION Be sure to close the HOLD FLAP for safety when removing the DCP. Attaching the DCP 1. Insert the right side of the DCP into the main unit. 2. Insert the left side of the DCP into the main unit. [SOURCE] button DCP [FRONT OPEN] button 2. Deeply push in [FRONT OPEN] button to unlock the front panel. ∗ If the front panel does not open fully, gently open it with your hand. DCP 3.
English 9. CAUTIONS ON HANDLING Liquid crystal panel/Generalities Owner’s manual For a longer service life, be sure to read the following cautions. • Be sure to store the liquid crystal panel inside the main unit when parking the car outdoors for long period of time. The liquid crystal panel will operate properly in a temperature range of 0 to 60˚C. • Don’t allow any liquids on the set from drinks, umbrellas etc. Doing so may damage the internal circuitry.
DVD Video Features This unit provides the following functions in addition to the high image quality and sound quality of DVD video. Notes: • The functions described in the section, “Features”, for example, the recorded language, subtitles, angles, etc. differ with the DVD video disc. Refer to the instructions provided with the DVD video. • Some disc functions may operate differently than described in this manual.
English Discs TV color system This DVD player plays NTSC discs only and cannot be used for playback of SECAM discs and PAL discs. Playable discs This DVD video player can play the following discs. Owner’s manual Playable discs DVD video discs video CDs CD TEXT Audio CDs A CD Extra disc is a disc in which a total of two sessions have been recorded. The first session is Audio session and the sedond session Data sessioin.
Basic Operations Note: Be sure to read this chapter referring to the front diagrams of chapter “3. CONTROLS” on page 5 (unfold). Engine ON position Turning on and off the power Note: • Be careful about using this unit for a long time without running the engine. If you drain the car’s battery too far, you may not be able to start the engine and this can reduce the service life of the battery. 1. Press the [SOURCE] button. 2. The illumination and display on the unit light up.
English Basic Operations Opening and turning the liquid crystal panel Owner’s manual WARNING • To prevent the battery from going dead, operate this unit with the engine running, if possible. • When the liquid crystal panel is operating, be careful not to get your hand or finger caught between the panel and main unit or the instrument panel of the car. • Do not move the liquid crystal panel by hand. Standing up the liquid crystal panel 1.
Adjusting the AUDIO 1. Press the [OPEN] button and the liquid crystal panel is housed automatically. Note: • When leaving this unit unused for a long period of time or leaving your car, be sure to house the liquid crystal panel into the main unit. Note: • When the separately-sold 5.1 ch Surround Decoder (DVH940) is used, the bass and treble tone adjustments cannot be made. To adjust the tone, refer to the section “5.1 ch Surround Decorder Operations”.
English Basic Operations Adjusting the MID Owner’s manual The MID gain, MID frequency (center frequency) and MID Q can be adjusted as follows. 1. Press the [ADJ] button, then touch the [AUDIO] key. 2. Touch the [MID] key. 3. When the bass type selection screen is displayed, touch the key for the desirable type to select it. 4. Touch the [w] or [z] key to adjust to desirable level. GAIN : –6 to 6 (The factory default setting is “0”) FREQ. : 700Hz/1kHz/2kHz (The factory default setting is “1k”) Q : 1.
Adjusting the MONITOR Notes: • This function is not available when the display is stored. • The HUE setting can be adjusted only when the NTSC mode is selected. • Switch to the VISUAL/DVD player(DVD video or video CD)/DVD changer/TV mode you see. 1. Press the [ADJ] button to switch to the ADJUST mode menu. 2. Touch the [MONITOR] key. 3. Touch the [MONI ADJ] key to display [BRIGHT], [HUE] and [COLOR] key. Touch the [BRIGHT], [HUE] and [COLOR] key to adjust BRIGHT, HUE and COLOR.
English Basic Operations Adjusting the GENERAL Setting the BEEP Owner’s manual ∗ The sound heard when you make operations is called “beep”. The unit can be set up so that it does not produce this beep sound. ∗ The factory default setting is “BEEP ON”. 1. When the panel is open, press the [ADJ] button to select the ADJUST mode menu. 2. Touch the [GENERAL] key. Touch the [BEEP] key to select “ON” and “OFF”. 3. Touch the [RTN] key, [ESC] key, or press the [ADJ] button.
English Basic Operations 2-ZONE Function About the 2-ZONE function Setting the 2-ZONE function ∗ The factory default setting is “OFF”. 1. Hold the remote control unit’s [2-ZONE] button depressed (about 1 second) to turn the 2-ZONE function ON. • The function can also be switched by touching and holding the main menu’s [2ZONE] key (about 1 second).
English Basic Operations Monitor image and sound with 2-ZONE ON/OFF ● With 2-ZONE function OFF Owner’s manual Front monitor lock ON (∗1) Visual connection [OTHERS] Front image Image of device (receiver screen) connected to the Visual terminal (∗3) Visual connection [NAVI] Image of device connected to the Visual terminal Front monitor lock OFF Visual connection Visual connection [OTHERS] [NAVI] Displays image of mode selected using the [SOURCE] button.
FM reception Listening to the radio 1. Press the [SOURCE] button and select the Radio mode. The frequency is displayed. 2. Press the [BAND] button and select the radio band. Each time the button is pressed, the radio reception band changes in the following order: FM1 ➜ FM2 ➜ FM3 ➜ AM ➜ FM1... 3. Press the [a] or [d] button to tune in the desired station. Seek tuning 1. Press the [BAND] button and select the desired band. (FM or AM) 2. Tune in to a station.
English Radio Operations ●Using the LIST screen 1. Touch the [LIST] key. Owner’s manual 1. Press the [BAND] button and select the desired band. (FM or AM) 2. Touch the [LIST] key. 3. Touch and hold the [AS] key for 2 seconds or longer. The stations with good reception are stored automatically to the preset channels. Preset scan 2. Touch the corresponding [DIRECT] key to recall the stored station. ∗ You can select the desired band to touch the [BAND] key.
Changing DVD System Settings Selecting the DVD SETUP menu 1. Touch the screen to show the menu screen. 2. Touch the [SUB] key to display the sub menu. 3. Touch the [SETUP] key to display the DVD SETUP menu. 4. Touch the [z] key. Touch the [w] key to return to the previous menu. This function allows displaying the important part of image fully on the screen. In some cases, image is displayed while being panned (scrolled). • N LB : A black zone is created in the top and bottom areas of the screen.
English DVD Video Player Operations 2. Touch the key to select a desired language to set it. ∗ The factory default setting is “ENGLISH”. Owner’s manual 3. Touch the [RTN] key ([ESC] key). Setting up the audio language 1. Following the steps 1 to 3 in “Selecting the DVD SETUP menu”, touch the [AUDIO LANGUAGE] key. 2. Touch the key to select a desired language to set it. Setting up the country code Set up the country number for setting up of the parental level. 1.
LEVEL7 LEVEL6 LEVEL4 LEVEL3 LEVEL1 NC-17 (NO ONE 17 AND UNDER ADMITTED) R (RESTRICTED) PG-13 (PARENTS STRONGLY CAUTIONED) PG (PARENTAL GUIDANCE SUGGESTED) G (GENERAL AUDIENCES) • The contents that the parental level restricts varies with the country code. Basic Operations Loading a disc Insert a disc into the centre of the insertion slot with the label side facing up. The disc plays automatically after loading. Notes: • Never insert foreign objects into the disc insertion slot.
English DVD Video Player Operations Ejecting a disc Owner’s manual 1. Press the [Q] button a disc ejects. “EJECT” appears in the display. The play mode then switches to Radio. ∗ If a disc is left in the ejected position for 15 seconds, the disc is automatically reloaded (Auto reload). In this case, however, the play mode will remain set to Radio. Note: • If you force a disc into before auto reloading, this can damage the disc. 4.
Fast forward and fast backward 1. Press and hold the [a] or [d] button during playback. Press and hold the button, and the playback speed becomes 5-time faster first and then 20-time faster 3 seconds later. Release the button, and the normal speed is restored. • No audio is reproduced during fast forward and fast rewind operation. • The same operation can be performed by touching the screen to display the menu screen, then touching the [å] or [∂] key.
English DVD Video Player Operations Owner’s manual Scan playback Switching among languages Scans and plays back all chapters recorded on the DVD-Video, the first 10 seconds for each. 1. Touch the screen to display the menu, then touch the [SUB] key. 2. Touch the [SCAN] key, then touch the [RTN] key. The message “C.SCN” will be displayed. After scan playback of all chapters on the disc, chapter scanning through the same disc is performed again.
Switching angles 2. Touch the [ ] (Angle mark) key during playback. Each time you touch the key, you can switch among angles. • Depending on the disc, up to 9 angles may be recorded. For details, see the mark of the disc ( : Indicates multi-angle). • Depending on the disc, angles may switch smoothly or switch with a momentary still image. • When the power is turned on and when the disc is changed with new one, the language set at the time of factory shipment is selected.
English DVD Video Player Operations Owner’s manual Slow playback Fast forward and fast backward 1. Press the [s] button then press and hold the [d] button. While the button is being pressed, slow playback continues at the speed 1/3 times the normal playback. • Slow playback cannot be performed in the backward direction. In addition, audio cannot be reproduced during slow playback. • The same operation can be performed by touching the screen to display the menu screen, then touching the [å] or [∂] key.
Skipping a track (searching) 1. Press the [a] or [d] button during playback. Tracks are skipped, as many as the times the button is pressed, and playback starts. • Press the [d] button, and playback starts from the beginning of the next track. • Press the [a] button, and playback starts from the beginning of the current track. When this button is pressed again within about 2 seconds, playback starts from the beginning of the previous track.
English DVD Video Player Operations Selecting a track on the LIST screen Owner’s manual This function allows you to select tracks from a displayed list. 1. Touch the [LIST] key. The list menu will appear. 2. Press the [w] or [z] button to change the track display. 3. Touch the desired track title key. The corresponding track will begin playback. • The titles will scroll when the selected track’s “ ” mark is touched. 4. Press the [RTN] key to return to the previous screen. Other various play functions 1.
Regarding MP3 folder creation Up to 8 folder levels (including the root directory) can be created for MP3 files (items 1 – in the illustration). However, on this unit, folders created above the third level will be converted to 2 levels. 1 2 3 1 4 2 3 4 • Folders containing no MP3 files are not recognized. • Only folders containing tracks (1 to 4 in illustration) are given numbers and displayed on the list. Pausing playback 1. Press the [s] button or touch the [s] key during playback. Playback pauses.
English DVD Video Player Operations Owner’s manual faster 3 seconds later. Release the button, and the normal speed is restored. • The same operation can be performed by touching the screen to display the menu screen, then touching the [å] or [∂] key. Selecting a folder/track on the LIST screen 1. Touch the [LIST] key during playback. Folders (tracks) are displayed. 2. Touch the [w] or [z] key to select a folder and touch the folder name.
Controlling the iPod ● Select the iPod mode 1. Connect the iPod to the connector. 2. Press the [SOURCE] button. • The iPod mode can also be selected by touching the iPod icon on the SOURCE menu. Title display (*) [REPEAT] key [PLAYLIST] key Notes regarding use of Apple iPod • When using an iPod, after connecting the iPod to the connector, select the iPod mode by either pressing the [SOURCE] button, or by touching the iPod icon on the SOURCE menu.
English iPod Operations Owner’s manual [s s] key Use to control playback and pause. [å], [∂] keys Use to perform track selection. Press continuously to enable fast-forward and fastbackward. [SHUFFLE] key Use to switch the shuffle mode, in the order Song Shuffle ➜ All Shuffle ➜ Shuffle OFF. The default value is Shuffle OFF. When enabled, this function performs playback of tracks in random order, regardless of the order in which they are recorded.
This function is available when a VTR, etc. is connected to the visual terminal. Note: • When an optional DVD (CD) changer is connected through the CeNET cable, this unit controls all DVD (CD) changer functions. This unit can control a total of 2 changers (CD and/or DVD). WARNING For your safety, the driver should not watch the VTR, etc. or operate the controls while driving. Please note that watching and operating the VTR, etc. while driving are prohibited by law in some countries.
English CD Changer Operations Owner’s manual When the panel is open: 1. Touch the [DISC], [TRACK], [ARTIST], or [USER] key to select the desired title. The selected titles except for the user title scroll once. Selecting with a track number Selecting a CD When the panel is closed: Each of the [DIRECT] buttons corresponds to a disc loaded into the magazine. ●Selecting a disc from 1 to 6 Press the corresponding [DIRECT] button (1 to 6) to select the desired disc.
TOP function * DISC [RANDOM]; disc random playback The disc random play selects and plays individual tracks or discs automatically in no particular order. 3. Touch the [RTN] key, return to the previous screen. ∗ Other various play functions This function continues on the disc until it is cancelled or the mode is changed. 1. Touch the [SUB] key. ∗ Use to display current play status, and also as the cancel key. 4. To cancel play, touch the [T.SCN] ([D.SCN], [T.RPT], [D.RPT], [T.RDM] or [D.RDM]) key. 2.
English Owner’s manual DVD Changer Operations TV Operations Only basic operations of DVD changer can be performed from the unit. Use the remote control unit to perform the following functions. • SCAN, REPEAT, RANDOM function • V-CD PBC function ON/OFF • DVD SETUP function, AUDIO, SUBTITLE, ANGLE setting function For details on operations other than those described below, see DVD player Operation. For details on DVD changer precautions, refer to the supplied owner’s manual.
Seek tuning 1. Press the [BAND] button and select the desired TV band (TV1 or TV2). 2. Press the [d] or [a] button to automatically seek a station. Press the [d] button to automatically tune up the frequency band to the next available TV station; press the [a] button to automatically tune down. ∗ The same operation can be performed by touching the screen to display the menu screen, then touching the [å] or [∂] key. Selecting with a station number 1.
English Owner’s manual TV Operations SIRIUS Operation 2. Touch the screen to display the menu, then touch the [LIST] key. 3. Touch and hold one of the [DIRECT] key for 2 seconds or longer to store the current station into the preset memory. What is Sirius Satellite Radio? Auto store Auto store selects 6 TV stations automatically and stores each one into a preset memory.
Selecting with a station number Press the [BAND] button to select a band. Each press of the button changes the display as shown below. SR1 ➜ SR2 ➜ SR3 ➜ SR1 … ● Information displayed during reception The following information is displayed when Sirius Radio cannot be received normally.
English SIRIUS Operation Owner’s manual ∗ This changes the seek mode to manual mode and the “MANU” indicator on the display lights. When this operation is performed in manual mode, the seek mode is engaged and the “MANU” indicator on the display goes off. Note: • The receiver automatically reverts to the seek mode when the [a] or [d] button is not used for 7 seconds in the manual mode. 2. Press the [a] or [d] button. The receiver moves to channels above or below the current channel one by one.
Presetting a category Entering titles A category can be preset by registering specific categories in [DIRECT] keys 1 to 6. Then the desired category can be recalled by pressing the corresponding [DIRECT] keys. 1. Touch the [SUB] key. 2. Touch the [ITEM] key to display a category. 3. Touch the [z] or [w] on the screen to select the desired category on the screen. 4. Touch the category you wish to store in memory. 5. Touch the [PRESET] key to open the preset screen. 6.
English Other Functions Title list play Owner’s manual You can display a list of titles, then select the CD track, disc or broadcast station to listen to from that list. ∗ You can not display a title list with the unit in Seek, Preset Scan, Auto store (Tuner or TV) mode. Cancel those operation modes before to display a title list. 1. Touch the screen (TV mode only). 2. Touch the [LIST] key to display the LIST screen. A title list is displayed.
●Dolby PL II CONTROL This function is available when a 5.1 ch Surround Decoder (DVH940) is connected. When the 5.1 ch Surround Decoder (DVH940, sold separately) is CeNET connected, the 5.1 ch Surround Decoder Control unit (DVC940, sold separately) cannot be used. This section describes operation procedures only. For other details, refer to the owner’s manual supplied with the 5.1 ch Surround Decoder. ∗ This function is available only when the MUSIC MODE is selected for Dolby PL II.
English 5.1 ch Surround Decoder Operations Owner’s manual ●SPEAKER GAIN This function sets speaker output level. DSF mode ∗ This function is not available for speakers whose SPEAKER SEL setting is set to OFF. DSF effect ON/OFF 3-1. Touch the [SPEAKER GAIN] key to show the submenu. 3-2. Touch the [FRONT L], [CENTER], [FRONT R], [SURROUND R], [SURROUND L] or [SUB WOOFER] key to set respective item. 3-3. Touch the key to make adjustments in the range –10 dB to +10 dB in 1 dB step increments.
Setting and storing P.EQ Properties ∗ The factory default setting is “P.NOISE”. This function selects “P. NOISE” or “MUSIC”. ●SPEAKER SELECT ∗ The factory default setting is “FRONT”. This function selects “FRONT”, “CENTER” or “SURROUND”. ●BAND ∗ The factory default setting is “BAND1”. Select the channel to be compensated (“BAND1”, “BAND2”, “BAND3”). ●FREQUENCY ∗ The factory default setting is “1 kHz”. Select the center frequency that you want to compensate from the range of 18 Hz to 20 kHz.
English 12. IN CASE OF DIFFICULTY Problem Cause Measure Owner’s manual Power does not turn on. (No sound is produced.) Fuse is blown. Replace with a fuse of the same amperage. If the fuse blows again, consult your store of purchase. Incorrect wiring. Consult your store of purchase. Nothing happens when buttons are pressed. The microprocessor has malfunctioned due to noise, etc. Turn off the power and remove the DCP. Press the reset button for about 2 seconds with a thin rod.
Measure The image is not displayed. The parking brake is not pulled. Check that the parking brake is applied. The display is dark. The brightness control is too low. Adjust the brightness properly. The operating condition is not good. The temperature inside the vehicle may be 0˚C or less. Set to an appropriate temperature (25˚C or so) and check it again. The headlight of the vehicle is lit.
If an error occurs, one of the following displays is displayed. Take the measures described below to eliminate the problem. DVD PLAYER Owner’s manual Cause Measure ERROR 2 A CD is caught inside the CD deck and is not ejected. This is a failure of CD deck’s mechanism and consult your store of purchase. ERROR 3 A CD cannot be played due to scratches, etc. Replace with a non-scratched, non-warped-disc. ERROR 6 A CD is loaded upside-down inside the CD Eject the disc then reload it properly.
English 14. SPECIFICATIONS LCD Monitor Frequency Range: 87.9 MHz to 107.
English Owner’s manual VRX755VD 64
English VRX755VD Installation and Wire connection manual 1. 2. 3. 4. 5. 6. 7. 8. 9. BEFORE STARTING ............................................................... PACKAGE CONTENTS ........................................................... GENERAL CAUTIONS ............................................................ CAUTIONS ON INSTALLATION .............................................. INSTALLING THE MAIN UNIT ................................................. REMOVING THE MAIN UNIT ....................
English 3. GENERAL CAUTIONS Installation and Wire connection manual 1. Do not open the case. There are no user serviceable parts inside. If you drop anything into the unit during installation, consult your dealer or an authorized CLARION service centre. 2. Use a soft, dry cloth to clean the case. Never use a rough cloth, thinner, benzine, or alcohol, etc. For tough dirt, apply a little cold or warm water to a soft cloth and wipe off the dirt gently. 4. CAUTIONS ON INSTALLATION 1.
English 5. INSTALLING THE MAIN UNIT ■ Universal Mount Notes: 1) Some car models require special mounting kits for proper installation. Consult your Clarion dealer for details. 2) Fasten the front stopper securely to prevent the main unit from coming loose.
■ Fixed Mount (TOYOTA, NISSAN and other ISO/DIN equipped vehicles) English Installation and Wire connection manual This unit is designed for fixed installation in the dashboard. If the vehicle is equipped with a factory-installed radio, install the main unit with the parts and screws marked (∗). (Figure 8) If the vehicle is not equipped with a factoryinstalled radio, obtain an installation kit to install the main unit in the following procedure. 1. Remove the screws from both side of the main unit.
pull the main unit out by the hook plate. (Insert both the right and left edges of the hook plate.) (Figure 9) Note: Keep the hook plate. You cannot remove the main unit without disengaging the hook plate. Instrument panel Universal mounting bracket 2-Hook plate Main Unit Spring Outer escutcheon A B Figure 9 7. CAUTIONS ON WIRING 1. Be sure to turn the power off before wiring. 2. Be particularly careful where you route the wires. Keep them well away from the engine, and exhaust pipe, etc.
English 8.
English Installation and Wire connection manual Yellow +12V main power Black Ground Purple Purple/Black Grass-green Glay Rear right + Rear right Parking brake Front right + Glay/Black White White/Black Green Green/Black Blue/White Front right Front left + Front left Rear left + Rear left Amplifier turn-on lead Orange/White Illumination Red +12V accessory Brawn Phone mute (∗1) Blue Auto antenna VRX755VD 71
English ■ Connecting the Accessories • Connection to the external amplifier The external amplifier can be connected unless the 5.1ch Surround Decoder is connected. For detailed information, refer to the instruction manual of the 5.1ch Surround Decoder. Installation and Wire connection manual • Connection to the CCD camera for vehicle The CCD camera for vehicle can be connected to CCD terminal on the tuner amp unit. For detailed information, refer to the instruction sheet or manual for the CCD camera.
English 9.
■ Sample System 2 English VRX755VD RCA cable (sold separately) Installation and Wire connection manual VTR Visual input (Glay) Non fader output Front Speakers RCA video cable (included the TV tuner) RCA cable (sold separately) Rear Speakers 4-Channel Amplifier (TTX7501z) (APA4320) RCA cable (included the DVH940) CeNET cable (included the DVH940) RCA cable (sold separately) Center speaker built-in amplifier (SRK5) (Black) 5.
