Model SR9000 installation guide ProSecurity NOTE: This product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained professional may result in severe damage to a vehicle’s electrical system and components.
© 2007 Directed Electronics—all rights reserved
table of contents what is included . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 warning! safety first . . . . . . . . . . . . . . . . . . . . . . . . 4 installation points to remember. . . . . . . . . . . . . . . . 5 before beginning the installation . . . . . . . . . . . . . 5 after the installation. . . . . . . . . . . . . . . . . . . . . . 5 deciding on component locations . . . . . . . . . . . . . . . 6 locations for the siren . . . . . . . . . . . . . . . . . . . . .
what is included ■ The control module ■ The plug-in status LED ■ SST 2 way receiver/antenna ■ The plug-in Valet/Program switch ■ One remote transmitter P/N SAA7701U ■ A hood pinswitch ■ A Stinger Doubleguard shock sensor ■ A toggle (override) switch ■ A 514N Neosiren warning! safety first The following safety warnings must be observed at all times: ■ Due to the complexity of this system, installation of this product must only be performed by an authorized Ungo dealer.
■ After the remote start module has been installed, test the remote start module in accordance with the Safety Check outlined in this installation guide. If the vehicle starts when performing the Neutral Safety Shutdown Circuit test, the remote start unit has not been properly installed. The remote start module must be removed or properly reinstalled so that the vehicle does not start in gear. All installations must be performed by an authorized Ungo dealer.
deciding on component locations locations for the siren Some things to remember about mounting the siren: ■ Keep it away from heat sources, such as radiators, exhaust manifolds, turbochargers, and heat shields. ■ Mount it where a thief cannot easily disconnect it, whether the hood is open or shut. Both the siren and its wires should be difficult to find. This usually involves disguising the wire to look like a factory harness. ■ We recommend against grounding the siren to its mounting screws.
mounting the antenna The antenna position should be discussed with the vehicle’s owner prior to installation, since the antenna may be visible to the vehicle’s operator. The best location for the antenna is centered high on either the front or rear windshield. For optimal range, the antenna should be mounted vertically. It can be mounted horizontally in relation to the windshield or under the dashboard away from metal, but range will be diminished.
locations for valet/program switch IMPORTANT! When the vehicle is delivered, please show the user where this switch is located and how to disarm the system with it. Ensure that the location you pick for the switch has sufficient clearance to the rear. The switch should be well hidden. It should be placed so passengers or stored items (such as in a glove box or center console) cannot accidentally hit it. The switch fits into a 9/32-inch hole. This system has Remote Valet.
locations for the optional starter kill relay If optional starter kill relay or its connections are immediately visible upon removal of the under-dash panel, they can easily be bypassed. Always make the relay and its connections difficult to discern from the factory wiring! Exposed yellow butt connectors do not look like factory parts, and will not fool anyone! For this reason, routing the optional starter kill wires away from the steering column is recommended.
finding the 12V switched ignition wire The ignition wire is powered when the key is in the run or start position. This is because the ignition wire powers the ignition system (spark plugs, coil) as well as the fuel delivery system (fuel pump, fuel injection computer). Accessory wires lose power when the key is in the start position to make more current available to the starter motor. How to find (+)12V ignition with your multimeter: 1. Set to DCV or DC voltage (12V or 20V is fine). 2.
finding the accessory wire An accessory wire will show +12V when the key is in the accessory and run positions. It will not show +12V during the cranking cycle. There will often be more than one accessory wire in the ignition harness. The correct accessory wire will power the vehicle's climate control system. Some vehicles may have separate wires for the blower motor and the air conditioning compressor. In such cases, it will be necessary to add a relay to power the second accessory wire.
finding a (+) parking light wire The (+) parking light wire is often found near the switch. Many cars have the switch built into the turn signal lever, and in these cars the parking light wire can be found in the steering column. The same wire is often available in the kick panel or running board. NOTE: Many Toyotas, as well as many other Asian vehicles, send a (-) signal from the switch to a relay. The relay then sends (+)12V to the bulbs.
Once you have determined the wire color, the easiest place to connect to the wire is often at the kick panel, at the windshield pillar, or in the running board. When an easy location is not available, running a wire to the domelight itself is often the best solution. How to find a door pin switch trigger wire with your multimeter: 1. Set to DCV or DC voltage (12V or 20V is fine). 2. In most Fords, fasten the (-) probe of the meter to chassis ground.
primary harness (H1), 12-pin connector H1/1 H1/2 H1/3 H1/4 H1/5 H1/6 H1/7 H1/8 ______ ______ ______ ______ ______ ______ ______ ______ RED/WHITE RED BROWN (-) 200 mA CHANNEL 2 VALIDITY OUTPUT (+) CONSTANT POWER INPUT (+) SIREN OUTPUT EMPTY NOT USED BLACK (-) CHASSIS GROUND INPUT VIOLET (+) DOOR TRIGGER INPUT, ZONE 3 BLUE (-) MULTIPLEXED INPUT, ZONE 4 GREEN (-) DOOR TRIGGER INPUT, ZONE 3 H1/9 ______ BLACK/WHITE H1/10 ______ WHITE/BLUE H1/11 ______ WHITE H1/12 ______ ORANGE (-) 200 mA DO
door lock harness, 3-pin connector 1 ______ 2 ______ 3 ______ LIGHT BLUE (+) LOCK (-) UNLOCK OUTPUT EMPTY NOT USED GREEN (-) LOCK (+) UNLOCK OUTPUT Note: Refer to TechTip 1041 for wiring information.
heavy gauge inline connector key switch interface 1 2 3 4 5 6 7 8 ______ ______ ______ ______ ______ ______ ______ ______ PURPLE GREEN RED ORANGE PINK RED PINK/WHITE RED/WHITE (+) STARTER OUTPUT TO STARTER (STARTER SIDE) STARTER INPUT FROM IGNITION (KEY SIDE) (+) HIGH CURRENT 12V INPUT (+) OUTPUT TO ACCESSORY CIRCUIT (+) OUTPUT TO PRIMARY IGNITION CIRCUIT (+) (30A) HIGH CURRENT 12V INPUT (+) OUTPUT TO SECOND IGNITION CIRCUIT (+) (30A) HIGH CURRENT 12V INPUT remote start harness (H3), 5-pin connector H3/
primary harness (H1) wire connection guide H1/1 RED/WHITE channel 2, 200mA (-) output When the system receives the code controlling Channel 2, for longer than 1.5 seconds, the red/white wire will supply an output as long as the transmission continues. This is often used to operate a trunk/hatch release or other relay-driven function. IMPORTANT! Never use this wire to drive anything but a relay or a low-current input! The transistorized output can only supply 200 mA of current.
H1/5 BLACK (-) chassis ground connection Remove any paint and connect this wire to bare metal, preferably with a factory bolt rather than your own screw. (Screws tend to either strip or loosen with time.) We recommend grounding all your components, including the siren, to the same point in the vehicle. H1/6 VIOLET (+) door trigger input, zone 3 This wire is used in vehicles that have a positive (+) switched dome light circuit.
H1/8 GREEN (-) door trigger input, zone 3 Most vehicles use negative door trigger circuits. Connect the green wire to a wire which shows ground when any door is opened. In vehicles with factory delays on the domelight circuit, there is usually a wire that is unaffected by the delay circuitry. This wire will report Zone 3.
H1/11 WHITE (+/-) selectable light flash output As shipped, this wire should be connected to the (+) parking light wire. If the light flash polarity jumper under the sliding door is moved to the opposite position (see Internal Programming Jumper section of this guide), this wire supplies a (-) 200 mA output. This is suitable for driving (-) light control wires in Toyota, Lexus, BMW, some Mitsubishi, some Mazda, and other model cars.
H1/12 ORANGE (-) ground-when-armed output This wire supplies a (-)500 mA ground as long as the system is armed. This output ceases as soon as the system is disarmed. The orange wire may be wired to an optional Directed Electronics 8618 starter kill relay. secondary harness (H2) wire connection guide H2/1 LIGHT BLUE (-) 200mA 2nd unlock output This wire provides a second unlock output for progressive locks. Refer to document 1041—Door Locking System Wiring Guide for specific applications.
be used to change the polarity. (See Finding the Wires You Need section of this guide.) Here are some common colors of this wire: ■ Chevrolet and GMC trucks - Light blue or dark blue ■ Ford Trucks - Black/pink ■ Dodge Ram Trucks - Orange/black or black/orange NOTE! A 1-amp diode must be installed in line on the factory wire between the wait-to-start indicator and the ECM. (See the following diagram for details.
H2/6 LIGHT GREEN/BLACK (-) factory disarm This wire sends a negative pulse every time the remote start is activated or the doors are unlocked. This can be used to pulse the disarm wire of the vehicle's factory anti-theft device. Use a relay to send a (-) or (+) pulse to the disarm wire as shown in the following diagrams.
ORANGE (+) accessory output Connect this wire to the accessory wire in the vehicle which powers the climate control system. PINK (+) ignition output Connect this wire to the ignition wire in the vehicle. PINK/WHITE (+) second ignition output Connect this wire to the second ignition wire in the vehicle. (See Finding the Wires You Need section.) NOTE: For vehicles that do not have a second ignition wire, this connection is not required. RED/WHITE (+) 12V input Connection for high current outputs.
Figure A Figure B H3/2 VIOLET/WHITE tachometer input This input provides the module with information about the engine's revolutions per minute (RPMs). It can be connected to the negative side of the coil in vehicles with conventional coils. In multi-coil and high energy ignition systems locating a proper signal may be more difficult. (See Finding the Wires You Need section of this guide.) Once connected, you must teach the system the tach signal.
horn, channel 6 harness (H4) wire connection guide H4/1 ORANGE/BLACK 200 mA programmable (-) channel 6 output This wire provides a (-) 200mA output whenever the transmitter button(s) controlling Channel 6 is pressed.
to the mechanical switch and a purple wire from the mechanical switch to the starter itself. Remember, this is only a rule of thumb and is not intended as a substitute for proper testing. We suggest the following procedure to test for vehicles manufactured in this way. NOTE: You must complete the remote start system installation before doing the following test. Ensure that the remote start system is functioning normally. This includes connecting to the brake as a shut-down.
However, due to future manufacturer changes in vehicles, it is possible that this may not apply to all vehicles. In addition, color variations are possible from model to model; make sure to test the circuit carefully. Please call Ungo Technical Support if you need assistance in making this interface. IMPORTANT! Once the interface is complete, attempt to remote start the vehicle with the door closed and the key in the ignition. The vehicle should not start. If it does, recheck the connections.
bypassing GM vehicle anti-theft systems (VATS) Vehicles with the GM VATS (Pass Key) systems have a resistor embedded in the ignition key. If the VATS decoder module does not measure the proper resistance when the vehicle is started, the starter and fuel pump may be disabled for up to ten minutes. An optional "VATS pack" of resistors is available (p/n 652T). One of the resistors in the pack will match the resistor in the key.
1995 and newer vehicle anti-theft systems (immobilizers) 1995 and newer vehicle anti-theft systems (immobilizers) require a bypass module. The bypass module allows for easy interfacing, while still maintaining the OEM system’s integrity.
ceiver will excite the transponder, which is located (but not visible) in the head of the ignition key. The key transponder will then send a unique code back to the transceiver for evaluation. If the code matches a valid code of the system, the vehicle will be allowed to start. Most of these transponder-based systems can be bypassed using p/n 556U. Some may require additional parts from the vehicle manufacturer. Consult you dealer for the applications.
shock sensor harness, 4-pin connector GREEN (-) multiplex input, zone 2 Inputs shorter than 0.8 seconds will trigger the Warn Away® response, while inputs longer than 0.8 seconds will trigger full alarm sequence and report Zone Two. If installing an optional Directed Electronics dual stage sensor, connect to the green wire as shown below. The diagram below eliminates the need for diodes to isolate the sensors.
3. The LED will light constant when the tach signal is learned. 4. Release the Valet/Program switch. programming jumpers tach threshold on/off In most cases, this jumper can be left in the OFF position. Some new vehicles use less than 12 volts in their ignition systems. The unit may have trouble learning the tach signal in these vehicles. Changing the jumper to the ON setting changes the trigger threshold of the digital tach circuit so it will work properly with these vehicles.
NOTE: For parking light circuits that draw 10 amps or more, the internal jumper must be switched to a (-) light flash output. P/N 8617 or a standard automotive SPDT relay must be used on the H1/11 light flash output harness wire. ™ transmitter/receiver learn routine The system comes with one transmitter that have been taught to the receiver. The receiver can store up to 4 different transmitter codes in memory.
CHANNEL NUMBER FUNCTION WIRE COLOR 1 Auto Learn Standard Configuration* (default) 2 Arm only 3 Disarm only 4 Silent Mode™/Remote Valet/Trunk Release 5 Remote Start 6 Channel 4 VIOLET/BLACK 7 Channel 5 WHITE/BLACK 8 Channel 6 9 Short Run/Turbo 10 Timer Mode 11 Arm/Disarm/Panic 12 Panic only 13 Defogger Control 14 Delete all transmitters** RED/WHITE *NOTE: For Auto Learn Configurations, see Transmitter Configurations section of this guide.
Learn Routine will be exited if: ■ Door is closed. ■ Ignition is turned off. ■ Program switch is pressed too many times. ■ More than 15 seconds between steps. transmitter configurations The transmitter can be programmed with the standard or single button arm/disarm configurations by using the Auto Learn functions in the Transmitter/Receiver Learn Routine. standard configuration A remote that uses the standard configuration operates similarly to many factory keyless entry remotes.
and and operate .........................rear defogger and ................operate............................
standard mode configuration 1. Auxiliary Channel Out 2. Receive Indicator 3. Signal Indicator 4. Transmit Indicator 5. Lock Status Indicator 6. Unlock Status Indicator 7. Arming Status Indicator 8. Disarming Status Indicator 9. Door Switch Input Indicator 10. Warn Away® Response Indicator 11. Siren Status Indicator 12. Battery Level Indicator 13. Trigger Response Indicator 14. Hood Switch Input Indicator 15. Ignition Switch Input Indicator 16. Sensor Response Indicator 17.
multi-level security arming Multi-Level Security Arming is a feature that allows the user to select which of the system's inputs or sensors will be active and which will be bypassed when the system is armed. (See Table of Zones section of this guide.) Multi-Level Security Arming can only be accessed from a standard configuration transmitter. Pressing the arm button of the standard configuration transmitter again within five seconds of arming the system will activate the Multi-Level Security feature.
system features learn routine The System Features Learn Routine dictates how the unit operates. It is possible to access and change any of the feature settings using the Valet/program switch. However, this process can be greatly simplified by using the Prosecurity programmer. Any of the settings can be changed and then assigned to one of up to four transmitters. This feature is called Owner Recognition.
5. Program the Feature. While holding the Valet/Program switch, you can toggle the feature on and off using the remote transmitter. Pressing the button that arms the system will select the one chirp or default setting. Pressing the button that disarms the system (or the Channel Two button when in the single button arm/disarm configuration) will select the two chirp setting. Note: Some features have more than two possible settings. Pressing setting, pressing 6.
To exit the learn routine: The learn routine will be exited if any of the following occurs: 1. Close the open door. 2. Turn the ignition on. 3. There is no activity for longer than 15 seconds. 4. The Valet/Program switch is pressed too many times. feature menus The default settings are indicated in bold type. Features that have additional settings that can be programmed using the Prosecurity programmer are indicated with an asterisk (*).
menu #2 - advanced features FEATURE NUMBER ONE-CHIRP SETTING (DEFAULT) TWO-CHIRP SETTING 2-1 30 second siren duration* 60 second siren duration* 2-2 Nuisance Prevention Circuitry ON Nuisance Prevention Circuitry OFF 2-3 Progressive door trigger Instant door trigger 2-4 Disarm from Valet, 1 pulse Disarm from Valet, 2-5 pulses 2-5 Door sensor bypass chirp ON Door sensor bypass chirp OFF 2-6 Ignition controlled domelight ON Ignition controlled domelight OFF 2-7 Unlock output 1 pulse Unl
menu #3 - remote start options FEATURE ONE-CHIRP SETTING (DEFAULT) TWO-CHIRP SETTING 3-1 Engine checking ON Engine checking OFF 3-2 Engine checking TACH Engine checking VOLTAGE 3-3 Run time: 12 minutes (1) Run time: 24 (2) or 60 (3) minutes 3-4 Parking lights flashing Parking lights constant 3-5 Crank time: 0.6 seconds (1) 0.8 (2), 1.0 (3), 1.2 (4), 1.4 (5), 1.6 (6), 1.8 (7), 2.0 (8), 4.0 (9) sec. 3-6 Voltage check - high Voltage check - low 3-7 Short Run/Turbo–1 min.
feature descriptions The features of the system are described below. Features that have additional settings that can be selected only when programming with the Prosecurity programmer are indicated by the following icon: menu #1 - basic features 1-1 ACTIVE/PASSIVE ARMING: When active arming is selected, the system will only arm when the transmitter is used. When set to passive, the system will arm automatically 30 seconds after the last door is closed.
1-8 FORCED PASSIVE ARMING ON/OFF: To use this feature, passive arming must be selected in Feature 1-1. When turned on, forced passive arming will ensure that the system will passively arm, even if a zone is left open or invalid. Forced passive arming occurs one hour after the ignition is turned off. 1-9 AUTOMATIC ENGINE DISABLE (AED) ON/OFF: AED is a full-time, passive starter disable that works independently of the security system.
2-2 NUISANCE PREVENTION® CIRCUITRY (NPC) ON/OFF: NPC stops repeated triggering of the same zone. If one zone is triggered three times in one hour, that zone is bypassed for one hour, starting from the time of the third trigger. During that hour, if the system sees a trigger on that zone again, the system resets the one hour timer. If one hour passes and the zone has not triggered again, the zone is activated and can trigger the system again.
pulse. 2-9 FACTORY ALARM DISARM WITH CHANNEL 2: In the default setting the factory alarm disarm output will disarm the factory alarm system any time the button(s) controlling Channel Two is pressed. 2-10 FACTORY ALARM DISARM—WITH UNLOCK, BEFORE UNLOCK, REMOTE START ONLY: In the default setting the factory alarm disarm output will disarm the factory alarm system any time the button(s) controlling Unlock is pressed.
menu #3 - remote start options 3-1 ENGINE CHECKING ON/OFF: In the default setting the remote start will monitor either the vehicle's tach wire or voltage depending on the programming of feature 3-2. If programmed OFF the vehicle will crank for the programmed crank time (feature 3-5) and will not verify with tach or voltage that the car is running. In the OFF setting, if the vehicle fails to start, the ignition can stay on for the entire run duration.
3-9 2nd IGNITION/ACCESSORY OUTPUT: This will allow the PINK/WHITE to be used as a 2nd ignition or an accessory. The default is 2nd ignition. 3-10 ACCESSORY STATE DURING WAIT-TO-START OFF/ON: This feature will allow the selection of the accessory output to be ON or OFF during wait-to-start.
and rearmed, and still allow NPC to bypass a faulty zone. When disarming the system, 5 chirps indicate NPC is activated. The LED will report the zone that has been bypassed. (See Diagnostics section of this guide.) valet mode To enter or exit valet mode with the valet/program switch: 1. Turn the ignition key on and then off. 2. At anytime during the next 10 seconds, press and release the Valet switch.
To turn the rear defogger output ON: 1. Press & release the and and buttons of the remote control. 2. The parking lights will flash 3-times. 3. The rear defogger output will once again activate when the vehicle is remote started. NOTE: If the remote start is On the lights will turn off then flash 3-times before returning to their normal output and the defogger output will activate as programmed.
table of zones When using the Diagnostic functions, use the Table of Zones to see which input has triggered the system. It is also helpful in deciding which input to use when connecting optional sensors and switches. ZONE NO. TRIGGER TYPE INPUT DESCRIPTION 1 Trunk Input BLUE (H1/7) 2 Multiplexed Shock Sensor Input Mux BLUE wire. 3 Door Trigger 4 Multiplexed Shock Sensor Input Mux GREEN wire 5 Ignition Yellow ribbon harness wire 6 Hood Brake Trigger GRAY on the 6-pin shutdown harness.
long term event history The system stores the last two full triggers in memory. These are not erasable. Each time the unit sees a full trigger, the older of the two triggers in memory will be replaced by the new trigger. To access long term event history: 1. With the ignition off, press and HOLD the Valet/Program switch. 2. Turn on the ignition. 3. Release the Valet/Program switch. 4. Press and release the Valet/Program switch within 5 seconds.
IMPORTANT! Make sure there is adequate clearance to the front and rear of the vehicle before attempting this test. a. Make sure the hood is closed and no other shutdown circuits are active. b. Set the emergency brake. c. Turn the ignition key to the run position but do not start the engine. d. Put the vehicle in Drive (D). e. Put your foot over the brake pedal but do not press down on it. Be ready to step on the brake to shutdown the remote start system. f. Activate the remote start system.
■ Door input does not respond with the progressive trigger, but with immediate full alarm: Does the Status LED indicate that the trigger was caused by the shock sensor? (See Diagnostics section of this guide.) The shock sensor, if set to extreme sensitivity, may be detecting the door unlatching before the door switch sends its signal. Reducing the sensitivity can solve this problem. ■ The Valet/Program switch doesn't work.
3. Check diagnostics. Sometimes a shutdown will become active during cranking or just after cranking. ■ The vehicle starts, but the starter keeps running. 1. Is the system programmed for engine checking off or voltage sense? When programmed for either of these features, the engine cranks for the preprogrammed crank time regardless of how long it takes for the vehicle to actually start. Adjust to a lower cranking time. 2.
ProSecurity Programmer wiring quick reference guide 58 © 2007 Directed Electronics—all rights reserved
© 2007 Directed Electronics—all rights reserved PURPLE starter side starter wire GREEN key side starter wire RED 12V constant input ORANGE accessory output BLUE (-) status output ORANGE (-) 200mA 2nd accessory output VIOLET (-) 200mA starter output PINK (-) 200mA 3rd ignition output These signals are from the Relay Satellite ribbon harness and are provided to drive additional optional relays.
Get Started Get Protected Ungo Pro Security 661 W. Redondo Beach Blvd. Gardena, Ca.
