WARNING The Clarion OHMD102 overhead monitor system is designed strictly for rear-seat entertainment. Viewing the monitor while operating a motor vehicle can result in serious injury and/or property damage. Clarion is not responsible for any injury and/or property damage as a result of the improper use or viewing of the monitor. English O H������� MD102 INTRODUCTION Welcome! Thank you for purchasing the Clarion OHMD102 overhead monitor system.
monitor ogical nvenience. e Screen The Clarion OHMD102 is a full-featured overhead entertainment center featuring 10.2 Wide-Screen Flip Down Monitor with TFT Active Matrix Display with 16:9/4:3 format. This system combines flexibility, reliability, and expandability all in one. Designed primarily for rear seat entertainment, the audio from the OHMD102 can be enjoyed privately through wireless headphones and/or incorporated into any head unit.
The Clarion OHMD102 have been tested and found to comply within the limits of a Class B digital device, pursuant of Part 15 of the FCC rules. These limitations are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and uses radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
OVERHEAD DVD PLAYER and BUTTONS 6-7 GENERAL INFORMATION 6-13 BASIC OPERATIONS 14-21 ADVANCED OPERATIONS 22-26 START-UP MENU SETTINGS 27-30 REMOTE CONTROL 31-33 HEADPHONE FUNCTIONS 34 INSTALLATION 35-42 PACKAGE CONTENT 43 TROUBLESHOOTING 44-45 GLOSSARY 46-49 SPECIFICATIONS 50 WARRANTY INFORMATION 51-52 English O H������� MD102 OHMD102 TABLE OF CONTENTS 5 ohmd 102 5 3/16/05, 6:35 AM
English O H������� MD102 OVERHEAD DVD PLAYER OVERHEAD DVD SYSTEM 1 2 1 Switch for interior lighting 2 POWER Turns system power on /off 6 ohmd 102 6 3/16/05, 6:35 AM
English O H������� MD102 OHMD102 OVERHEAD DVD PLAYOVERHEAD DVD SYSTEM 1 2 3 4 5 6 7 8 12 ������� English 11 10 9 1 2 3 EJECT button DVD: previous chapter; VCD/CD/MP3: previous track menu:move cursor downward DVD: next chapter VCD/CD/MP3: next track menu move cursor upwards 4 PLAY/ PAUSE button 5 MENU button 6 Fastreverse for playback 7 Fastforward for playback 8 SOURCE button 9 10.
Precautions and Safety Notices • This overhead monitor system is designed for use in 12V DC negative ground vehicles. • Do not operate the overhead monitor system in ways other than described in this manual. Doing so may result in damage to the monitor system and/or the vehicle, voiding the warranty of this product. • SAFETY FIRST! This overhead monitor system is designed for rear-seat entertainment ONLY.
Care And Maintenance English O H������� MD102 OHMD102 GENERAL INFORMATION Keep all liquids away from the OHMD102 overhead monitor system. Liquids inside the monitor will damage the electronics, and can result in electrical shock or fire. In the event that the unit should become wet, turn off the power and contact a local Clarion dealer for assistance. To clean the monitor, use a clean soft cloth and gently wipe the screen. If possible, use specially designed “monitor wipes” to clean the screen.
Preparing a New Disc New disc may have some roughness around the edge. The DVD player may not work properly or the video/sound reproduction may skip if such discs are used. Use a ballpoint pen or pencil to remove roughness from the edges of the disc.
Temperature and Moisture If the player is used while the interior of the vehicle is very cold, condensation may form on the disc or on the internal optical pickup system and prevent proper playing of the disc. If you suspect that condensation is an issue, eject the disc and inspect the playing surface. If necessary, remove the condensation with a clean soft cloth as described above.
CAUTION: Any inappropriate use of the device may expose the user to visible/invisible laser rays which exceed the limits for Class 1 laser products. Do not attempt to repair it yourself refer servicing it to a trained Clarion authorized dealer. Copyright Protection This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macro vision Corporation and other rights owners.
FILE and STRUCTURE The folder name and file name can be displayed as the title during MP3 play. However, the title must be within 31 and 27 single-byte alphabetical letters and numerals for the folder name and file name, respectively (not including an extension). Entering more letters or numerals than specified may cause an incorrect display. A disc with a folder having more than 8 hierarchical levels will conflict with MP3 system requirements and playback will be impossible.
OPENING THE OVERHEAD MONITOR Press the OPEN button to release the overhead monitor. Gently push down on the bottom of the monitor until it reaches the desired position. The monitor will turn on automatically when it is fully open. OPEN POSITION CLOSING THE OVERHEAD MONITOR Gently push the backside of the monitor until it clicks into the overhead monitor housing. The monitor will turn off automatically when it is returned to the closed position.
DISPLAY SETTINGS • Press the Monitor Setup button once or several times to call up the display settings. • Press the or buttons to change the value of the settings. Press the OK button to exit the display mode.
User Settings This function allows the display settings, brightness, contrast, color, tint sharpness to be saved for a specific user and then subsequently restored. • Set the desired values for the display settings. • Select LOADED by pressing the button to save the values as user settings. • Select STORED button pressing the button to restore the values user settings. Default Settings • Select DEFAULT and press the the display to its default settings.
Skipping Chapters/Tracks • Press one of the buttons during playback. • Press the button to jump to the next chapter (DVD) or track (VCD/CD). • Press the button to jump to the previous chapter (DVD) or track (VCD/CD). English O H������� MD102 OHMD102 BASIC OPERATIONS Repeating Chapters/Tracks • Press the REPEAT button once, or more than once to select the REPEAT MODE. The menu will follow in this order. DVD Functions • CHAPTER REPEAT ON The current chapter is repeated.
Time Display Functions Press the DISP button during playback to display different time information on the screen of the disc that is playing. DVD • Press the DISP button once the following information will be shown on the screen. TITLE 02 / 05 01 : 14 : 39 CHAPTER 001 / 027 Current title number and total number of titles. Current chapter number and total number of chapters, and elapsed total time. Press DISP button again. TITLE REMAIN 01 : 14 : 39 Press DISP button for a third time.
Press DISP button for a fourth time. English O H������� MD102 OHMD102 BASIC OPERATIONS CHAPTER ELAPSED 00 : 12 : 24 Press DISP button for the fifth time: The message on the screen will be cleared.
Title Button If the DVD has multiple titles recorded, you can select the preferred title from the title menu to start playback. • Press the TITLE button during playback. • The title menu is displayed. • Move the cursor to the desired title with the cursor buttons or • Confirm your selection by pressing the ENTER button. English O H������� MD102 BASIC OPERATIONS Selecting Audio Language DVD: • Press the AUDIO button once or more than once during playback to select the desired audio sound track language.
Zoom (magnification) Press the ZOOM button once or several times during playback to select the required amount of zoom. The zoom selection will be in the following order • OFF >1.5X >2X >3X >OFF. Selecting the Viewing Angle (DVD only) When the ANGLE MARK (camera angle) function is activated, the symbol is displayed on the screen when a scene with alternative camera angles is played from a DVD. • Press the ANGLE button once or several times while the symbol is displayed to select the various camera angles.
Advanced MP3 Operations Make sure that the MP3 files have a file format designation of .mp3 two different modes of MP3 playback are available: • WITH MENU • NO MENU The playback mode can be set in the SETUP menu under PREFERENCES WITH MENU . In this mode the display shows all the MP3 folders of the disc on the left, and the file names of the folder currently opened on the right. • In STOP mode: Use the and buttons to select between the left and right column.
Without Menu When the SMART NAV function is set to NO MENU, only the track (file) number and the elapsed time for the current file are displayed on the screen. All the tracks (files) of the MP3 CD inserted are played sequentially. NOTE: The folder cannot be selected in this mode. Repeat File/Directory (REPEAT) English O H������� MD102 OHMD102 ADVANCED OPERATIONS Press the REPEAT button once or more than once to select one of the following repeat modes: With Menu • REP-ONE Repeat the current MP3 file.
NEXT/PREVIOUS FILES During playback • Press the button to select the previous MP3 file. • Press the button to select the previous MP3 file. Fast Forward/Reverse • Press the or button during playback. Each time the button is pressed, the speed of fast forward/reverse changes in the following order. Normal playback, 2x, 4x, 6x, 8x. JPEG IMAGE CDs The DVD player supports the display of JPEG images. Ensure that the JPEG images have a file format designation .
• Press the button in order to pause or resume the slide show. • In order to start the slide show with a particular image from the folder currently selected, enter the number which appears after the image in the navigation menu using the numeric key buttons and press the ENTER button. Notes: JPEG images can be recognized by the camera symbol to the left of the filename. The directory can only be selected in STOP mode. Volume, color, contrast and brightness cannot be adjusted during image CD playback.
Image Overview (Digest Mode) • Press MENU. • Up to nine thumbnail JPEG images are displayed on the screen. • The images are assigned to the numeric key buttons on the remote control as follows: 1 2 3 4 5 6 7 8 9 • You can select the next/previous nine thumbnail images in the current directory using the << and >> buttons. • Press one of the numeric key buttons (1 to 9), in order to see the image in full screen image mode.
SETUP MENU Main page In STOP mode • Press the SETUP button. • The initial SETUP menu is displayed. • Select the preferred item by using the / buttons. • Press the ENTER button to confirm your selection. The following options will be available: English O H������� MD102 OHMD102 SET-UP MENU SETTINGS GENERAL SET-UP • This includes TV display TV Type For details please refer to the General set-up menu. SPEAKER SETUP • This output is stero only. AUDIO SET-UP • This selects all other AUDIO functions.
SETTINGS TV TYPE This system can play discs recorded in either PAL or NTSC formats. • Select MULTI format, if the video source supports PAL and NTSC. • Select NTSC format, if the video source supports NTSC only. • • Select PAL format, if the video source supports PAL only. English O H������� MD102 SET-UP MENU SETTINGS SPEAKER DOWN/MIX • Designed fo Audio set-u • The operat changed. The PIC MODE DUAL MONO • Select the programs. If you select AUTO, the system PIC mode will depend on the DVD disc.
SPEAKER SET-UP MENU DOWN/MIX • Designed for stero output only. Audio set-up menu OP MODE • The operating mode for the Dolby Digital decoder cannot be changed. The mode is always set to LINE MODE. DUAL MONO • Select the desired Dual mono mode for 1+1 coded Dolby Digital programs. English O H������� MD102 OHMD102 SPEAKER SET-UP MENU SETTINGS STEREO • Stereo-reproduction 1+1 program. CH1 for left channel, CH2 for right channel. CH1 MONO • CH1 Mono-reproduction.CH1 Left. output.
PREFERENCES SET-UP MENU AUDIO • Select the initial audio sound track language you prefer. SUBTITLE • Select the initial subtitle language you prefer. DISC MENU • Select the initial disc menu language you prefer. LOCAL • Select the region in which the system is to be operated (e.g. UNITED STATES). This setting affects the parental control function (parental guidance level for films). PARENTAL • Select the desired parental guidance level from the list.
REPLACING THE REMOTE CONTROL BATTERIES Open the battery compartment on the back of the remote control. Remove the discharged batteries. Insert two AAA Alkaline batteries. Note the correct polarity (marked inside the battery compartment). Close the battery compartment. CHANGING BULBS Carefully pry the transparent cover of the interior lights off the unit using a small screwdriver Replace the bulbs with the same type (12V/2 - 3 W). Snap the cover closed.
1 12 2 13 9 3 4 14 5 15 16 6 17 7 18 8 19 11 20 10 32 ohmd 102 32 3/16/05, 6:35 AM English O H������� MD102 INFRARED REMOTE CONTROL
1 English O H������� MD102 OHMD102 INFRARED REMOTE CONTROL POWER Turn systempower on / off 2 0 - 9 Numerickey buttons 3 PLAY/PAUSE 4 STOP 5 DVD: Next / previous chapter VCD/CD/MP3: Next / previous track MENU mode: Cursor up/down 6 Select the SUBTITLE language (dependingon the DVD disc) 7 AUDIO Select the audio soundtrack (depending on the DVD disc) 8 SETUP Display the SETUP menu of the DVD player 9 SOURCE Selects AV source (DVD, AV1 or AV2) 10 MENU Displays the DVD root menu 11 MUTE M
OPERATING HEADPHONES Power switch Press to activate the headphones. The power on the headphones will turn off automatically if an audio signal is not detected for over a minute. Volume adjustment switch Adjusts the volume of the sound in the headphones. 1 2 Note: • Headphones are not to be worn by the operator of the vehicle when driving. • Do not leave the headphones in a place subject to direct sunlight or extreme temperatures.
ABOUT INSTALLATION English O H������� MD102 OHMD102 INSTALLATION The installation of the OHMD102 overhead monitor system requires experience in both mechanical and electrical procedures. If you do not posses the necessary experience or tools to attempt this installation, contact a local Clarion dealer for assistance. Improper installation can result damage to the monitor and/or the vehicle.
INSTALLATION PROCEDURE 1. Identify the polarity of the dome light circuit and set the switch on the bottom of the overhead monitor housing. 2. Test fit the overhead monitor system on the ceiling of the vehicle, verifying it is not going to interfere with the safe operation of the vehicle. 3. Once the mounting location of the overhead monitor system has been determined, carefully mark the location with masking tape. 4.
10. Carefully hold the overhead monitor system to the mounting bracket . Align the mounting holes while screwing in the screws. Make sure the wires are not in the way while mounting the monitor. 11. Connect the Red wire of the power harness to the Accessory wire in the ignition harness. 12. Ground the Black wire of the power harness to a clean ground spot.
CONNECTING DIAGRAM If you are uncertain as to what the proper connections are please contact a qualified Clarion technician for further installation assistance.
AV Input 8-Pin Connector Pin Function 1 Audio Left Output 2 AGND 3 Audio Right Output 4 AGND 5 NC 6 Audio Left Output 7 NC 8 Audio Right Output GND AGND Shielding GROUND � � � � � � � English O H������� MD102 OHMD102 INSTALLATION AUDIO OUT CABLE � Wiring the OHMD102 Read the following precautions before wiring your system. • Disconnect the negative battery terminal before making any wiring connections. • Be particularly careful where you route wires.
SAMPLE INSTALLATION English O H������� MD102 OHMD102 INSTALLATION Roof Beam Support Optional Spacer Material (Installer Provided) Metal Bracket Screws ( NOT included) IR Transmitter Screws (included) Warning! Make sure that the screws you use to mount the bracket, monitor, or optional spacers are not to long! If the screws are to long, they will damage the roof of the vehicle. Take great care when planning this part of the installation.
English O H������� MD102 INSTALLATION MOUNTING PLATE self-tapping screws M4.
Package Contents English O H������� MD102 OHMD102 PACKAGE CONTENTS 1 OHMD102 1 Audio Video RCA Accessories 1 Audio Video Din Cables 1 Convenient External Game Port 1 Audio Output Din Cable 1 Four Pin Power Harness 1 Metal Mounting Bracket 4 Screws For Metal Mounting Bracket 1 Soft Black Rubber Gasket 1 Remote Control 43 ohmd 102 43 3/16/05, 6:36 AM
TROUBLESHOOTING English O H������� MD102 TROUBLESHOOTING SYMPTOMS In rare cases, your DVD system may not function the way you expect it to. Before calling for service please read the operating instructions and go through the following check list. 1. Player does not work when switching on ignition and pressing the POWER button. 2. The remote control does not work. 3. Discs skips during playback, distorted sound, frozen picture, Interference in the picture, player does not read disc at all. 4.
POSSIBLE REMEDY 1. Check fuses (unit and vehicle) and connections (see mounting instructions). Press the REST button. 2. Change the batteries in the remote control. Replace the batteries with two AAA Alkaline batteries. The infrared on the remote control or the unit is covered by objects or dirt. Clean the infrared lenses with a damp cloth. 3. Player cannot read the inserted disc due to disc damage or dirt on the surface. Clean the disc and attempt to replay. 4.
Dolby Surround Dolby Laboratories audio encoding technology that combines the information for two additional channels (Center Surround) in a standard stereo signal. The Dolby Surround signal can be played on any stereo equipment, however a Dolby Surround Decoder is needed to separate the Center and Surround channels from the stereo channels. Dolby Surround Pro Logic An optimized decoder technology for Dolby Surround encoded signals.
JPEG (Joint Photographic Expert Group) JPEG images are bit-mapped images that use a compression method in order to save memory space. Macro vision Copyright protection technology developed by Macro vision Corporation. Copyright owners can protect their videocassettes from unauthorized recording on VCRs by using Macro vision technology. English O H������� MD102 OHMD102 GLOSSARY MP3 Digital audio data compressed in MPEG1 Layer 3 format.
PG-13 (Parental Guidance 13) Allowed for viewing by children over 13 with parental supervision. R (Restricted) Parental supervision or the accompaniment by an adult is mandatory. NC-17 Contents unsuitable for children under 17 Other. Adult Only suitable for adults NR (Not Rated) No classification. PBC (Playback Control) Some VCD 2.0 Video CDs are encoded with playback control, allowing you to navigate through the disc contents with a menu.
VFD (Vacuum Fluorescent ) Display) This DVD player is equipped with a multi-color display with adjustable brightness. TFT (Thin Film Transistor) A technology for manufacturing large, high resolution LCD flatscreen displays (e.g. computer monitors, LCD TVs, etc.).
SPECIFICATIONS Model OHMD102 Screen size (Diagonal): 10.2"TFT Monitor Screen resolution: 800 (H) x 3 (RGB) x 480(V) Active area: 216.0 (H) x 129.6 (V) Signal system: Dual system NTSC/PAL Brightness: 300 cd/m2 Contrast ratio: 400:1(Typ.) Viewing angle: Left/right: 55/55 degrees Up/down: 35/50 degrees Video input level: 1.0 Vpp � 10 % Audio input level: 0.3 Vrms Humidity for normal operation: 10%~75% Carrier frequency for IR sensor: L-CH: 2.3 MHz R-CH: 2.
WARRANTY INFORMATION This product is warranted against all defects in material workmanship for a period of one year from the date of original purchase. Clarion ProAudio products, except for speakers, are covered by a two year limited warranty when installed by an authorized Clarion dealer.
5. The sole responsibility of Clarion under this limited warranty shall be limited to the repair of the product or replacement of the product, at the sole discretion of Clarion. 6. Product must be shipped in its original carton or equivalent carton, fully insured, with shipping charges prepaid. Clarion will not assume any responsibility for any loss or damage incurred in shipping. 7.
English O H������� MD102 OHMD102 NOTES 53 ohmd 102 53 3/16/05, 6:36 AM
