Owner’s manual & Installation manual NX509A 2-DIN MEMORY NAVIGATION & DVD MULTIMEDIA STATION WITH 7-inch TOUCH PANEL CONTROL NAVIGASI MEMORI & STASIUN MULTIMEDIA DVD 2-DIN DENGAN KONTROL PANEL SENTUH 7-inci
Thank you for purchasing the Clarion NX509A. English • Please read this owner’s manual thoroughly before operating this equipment. • After reading this manual, be sure to keep it in a handy place (e.g., glove compartment). Contents NX509A 1 Owner’s manual 1. FEATURES .................................................................................................................... 2 Expanding Systems.....................................................................................................
English 1. FEATURES Owner’s manual ■ USB Direct Connection for iPod® ■ All-in-one AV & Navigation unit with Touch Panel control ■ Sirf III GPS module with 20-channel receiver Expanding Systems Expanding audio features Expanding visual features Rear Vision Camera (CC2011E/ CAA185) Rear Monitor 4-Channel Amplifier VTR etc. iPod BLT370 Bluetooth® cellular phone Note: The items listed outside of the frames are the commercial products generally sold.
About playing a DVD-R/RW or DVD+R/RW disc This DVD player can play the following discs: This player can play DVD-R/RW and DVD+R/RW discs previously recorded in DVD video format or format with MP3/WMA/AAC/DivX files. Playable discs This player cannot play DVD Audio, DVD-RAM, Photo CDs, etc.
Multi-sound function English DVD video can store up to 8 languages for one film; select the language of your preference. • The languages stored on the disc are indicated by the icon shown below. Owner’s manual Multi-angle function A DVD video that is filmed from multiple angles allows you to select the angle of choice. • The number of recorded angles is indicated by the icon shown below.
Cleaning • Cleaning the cabinet Use a soft and dry cloth and gently wipe off the dirt. For tough dirt, apply some neutral detergent diluted in water to a soft cloth, wipe off the dirt gently, then wipe again with a dry cloth. Do not use benzene, thinner, car cleaner, etc., as these substances may damage the cabinet or cause the paint to peel. Also, leaving rubber or plastic products in contact with the cabinet for long periods of time may cause stains.
English About the Registered Marks, etc. Owner’s manual • This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. • Manufactured under license from Dolby Laboratories.
English [SRC] button • Press this button to display/hide the Source screen to switch the source mode. Owner’s manual Blink LED • When the Blink LED function is set to “On” from the System tab menu on the General screen, blinks when the ACC power is turned off. SD memory card slot • SD memory card function is available in the Navi mode. For more information about the SD memory card function, see your User Manual (for the Navi mode).
English Outline of Button and Touchkey Operation Turning the power on Owner’s manual Engine ON position System check The CeNET format utilized on this unit is provided with a system check function. When the system check function is performed under the following conditions, the power is automatically turned off. Once turn off the engine switch, then restart the engine again. • When power is first turned on after initial installation. • When an external device is connected or disconnected.
Tuner mode operation English (Source screen) Owner’s manual Switches the radio band. Selects Home/Travel modes. Seek tuning Manual tuning Preset ch. • Select desired station after selecting radio band.
DVD Video mode operation English (DVD Video mode screen) *2 (Source screen) Owner’s manual * Screen during DVD Video mode when automobile moving. (Options screen) (DVD top menu) *2 (Setup screen) Note: *2 If you do not touch the screen for about 7 seconds, all the keys on the screen will disappear. Touch the screen surface to redisplay them.
Adjusting the General settings English (Source or Mode screen) Owner’s manual (Settings screen) (General screen) (Display tab screen) (System tab screen) NX509A 11
Adjusting the Audio settings English (Source or Mode screen) Owner’s manual (Settings screen) (Others tab screen) (Audio screen) (Beat EQ tab screen) (BAL/FAD tab screen) 12 NX509A
❏ Functions of Remote Control Unit Buttons ❏ Names of buttons You can use the remote control unit to control the NX509A. When the 2-Zone function is ON, the controls work upon the Sub zone only. [SUBTITLE] [AUDIO] [ANGLE] [TOP MENU] [MENU] [E], [e], [T], [t] [ENT] [RETURN] [SOURCE] [BAND] [6] [–], [+] [R], [F] ❏ Inserting the Battery Note: • The steering wheel remote control operations work upon the Main zone even when the 2-Zone function is ON. [AUDIO] button • Press to set the Audio language.
English [SOURCE] button • Press to switch the source modes such as Tuner mode, DVD mode, etc. (in any mode) * Only DVD, USB, and AUX modes are selectable when 2-Zone ON. Owner’s manual • Keep pressing more than 1 second to turn the 2-Zone function ON/OFF. (in any mode) [RETURN] button • Press to return to the previous screen while the DVD or Video CD menu is being displayed. However, it may occur that this button operation dose not work on some discs.
2. Touch the [Open/Close] key. The operation panel will be opened. English Adjusting the Volume Owner’s manual 1. Press the [VOL –]/[VOL +] buttons to adjust the volume. [VOL –]: Decreases the volume. [VOL +]: Increases the volume. • The volume level indicated in the display is in a range from 0 (min.) to 33 (max.). CAUTION CAUTION While driving, keep the volume level at which external sounds can be heard.
English Owner’s manual Adjusting the angle of the operation panel Turning the Audio OFF The angle of the operation panel can be adjusted in the range of 0q to 30q 1. Touch the [o (Eject)] key to display the Eject screen. 2. Repeat touching the [Tilt] key to adjust the angle of the operation panel. Every touching the [Tilt] key tilts the operation panel forward or backward. The adjusted angle is stored in memory.
Turning the monitor on 1. Touch the monitor screen. The monitor screen is turned on, and resumes the last screen. • You can also turn on the monitor by pressing the [SRC] button. Displaying the Clock Screen You can change the screen to display only the digital clock on a black screen. 1. Touch the clock display on most screens. The Clock screen is displayed. 2. To return to the current mode screen, touch the monitor screen. • Pressing the [SRC] button displays the Source screen.
English ❏ Setting a disc Owner’s manual 1. Touch the [o (Eject)] key to display the Eject screen. 2. Touch the [Open/Close] key. The operation panel will be opened. 3. Insert a disc into the center of the insertion slot with the label side facing up. The disc will automatically be drawn into the DVD player. After setting a disc The system will automatically be switched to the relevant source media mode according to the disc, and start playing back the disc.
CAUTION After connecting an USB device 1. Confirm that data transfer is not performed on the USB media device. For the method to confirm it, see the operation manual of your USB media device. 2. Remove the USB media device from the USB connector. CAUTION Be sure to disconnect the USB media device while the vehicle’s engine is running. Otherwise, it may result in loss or damage to data on the USB media device. Do not stop the engine when the USB media device is connected.
English 2-Zone Function Changing the source mode About the 2-Zone function 1. Press the [SRC] button to display the Source screen. The 2-Zone function is a function that assigns separate source output to the Main zone (this unit) and Sub zone (the optional rear monitor) by simultaneously playing two sources in this system. Therefore, the rear passengers are allowed to enjoy a different video source from the source played on the operation panel of this unit.
Note: • The AUX2 mode cannot be assigned for the Sub zone. Setting the 2-Zone function 5. SOURCE OPERATIONS Radio Operations Listening to the radio 1. Press the [SRC] button, and touch the [Tuner] key. The Tuner mode screen is displayed, and the system resumes the last status of the Tuner mode. • The factory default setting is OFF. 1. Press the [SRC] button to display the Source screen. 2. Touch the [2-Zone] tab to display the 2-Zone tab screen. The source keys for the Sub zone are displayed. 3.
English Owner’s manual Seek tuning Manual memory 1. Touch the [Band] key to select the desired band (FM or AM). 2. Touch the [{ (Seek)] or [} (Seek)] key to automatically seek a station. • When touching the [{ (Seek)] key, the station is sought in the direction of higher frequencies. • When touching the [} (Seek)] key, the station is sought in the direction of lower frequencies. 1. Touch the [Home Travel] key to select the Home or Travel mode. 2.
❏ Changing the DVD System Settings ❏ Selecting the DVD Video mode Note: • If the Setup operation is performed in the middle of DVD video play, the disc will restart from beginning. Displaying the DVD Setup screen 1. Touch the screen to display the DVD Video mode screen. 2. Touch the [Options] key to display the Options menu. 3. Touch the [Setup] key to display the Setup screen. WARNING • Some videos may be recorded at a higher volume level than desired.
English ●When watching through a wide type of the rear monitor (16:9) Wide: Setting up the disc menu language • The factory default setting is “English”. 4-1. Touch the []] key of the Menu Language item. Owner’s manual 4-2. Touch the desired Language key you wish to set. 4-3. Touch the [Back] key. ●When watching through a conventional type of the rear monitor (4:3) Pan Scan: The leftmost and rightmost areas of the screen are cut off.
Setting up the country code LEVEL7 NC-17 (NO ONE 17 AND UNDER ADMITTED) LEVEL6 R (RESTRICTED) LEVEL4 PG-13 (PARENTS STRONGLY CAUTIONED) LEVEL3 PG (PARENTAL GUIDANCE SUGGESTED) LEVEL1 G (GENERAL AUDIENCES) 4-3. Touch the [ENT] key.
English Showing the DVD Video mode screen Owner’s manual The DVD Video mode screen is used to control the playback mode from the screen. 1. Touch the screen. The DVD Video mode screen is displayed. If you do not touch the screen for 7 seconds, the display will return to the playback screen. Selecting the screen size You can change the screen size to suit to the playback film. • The factory default setting is “Full Wide”. 1. Touch the screen to display the DVD Video mode screen. 2.
Key Pad Slow playback Fast forward and fast backward 1. Showing the DVD Video mode screen, touch and hold the [{ (Chapter)] or [} (Chapter)] key during playback. [{ (Chapter)] key: Fast forward [} (Chapter)] key: Fast backward The playback speed becomes 4-time faster at first and then 16-time faster 3 seconds later. Releasing the key resumes the normal speed playback. • No audio is reproduced during fast forward and fast backward operation.
English Searching with a chapter/title number Owner’s manual You can locate the beginning of a scene using the chapter numbers or title numbers recorded on the DVD video disc. • “Chapter” means a small segment to divide the “Title” (film) which is recorded on the disc. 1. Showing the DVD Video mode screen, touch the [Options] key. 2. Touch the [Direct] key. The Key Pad screen appears. • You can specify the title number by touching the [Title] key. 3.
Displaying/hiding the playback status 1. Showing the DVD Video mode screen, touch the [Options] key. 2. Touch the [On] or [Off] key of the P.Time item during playback. 3. Touch the [Back] key to return to the previous screen. Playback status is displayed on the screen. Title number Chapter number Playback time T01 C0 0 1 00 : 00 : 19 This system suppouts the Playback Control (PBC) function which is recorded on a Video CD for version 2.0 and used to control playback.
English ●When the Video CD menu is displayed For Video CD discs equipped with the PBC (Playback Control) function, the Video CD menu appears. After the Video CD menu is displayed, select an item in the following operations and play it back. Owner’s manual Note: • There are two types of Video CDs, and these differ in some operations and functions. For the operations and functions of a Video CD, see the documents attached to the Video CD.
• The factory default setting is “Off”. 1. Showing the Video CD mode screen, touch the [Options] key. 2. Touch the [On] or [Off] key of the P. Time item to set the function ON or OFF. 3. Touch the [Back] key to return to the previous screen. This system is a CD TEXT compatible model, and supports the display of the DISC TITLE, TRACK TITLE, and TRACK ARTIST (or DISK ARTIST) of the CD TEXT. Note: • This function is disabled when the PBC function is set to ON.
English Owner’s manual Pausing playback Scrolling track titles 1. Touch the [p] key during playback. Playback pauses. 2. To resume playback, touch the [p] key. Playback resumes. When a title or name displayed on the screen is longer than the text area, you can confirm the entire text by scrolling it. 1. Displaying the text you wish to scroll, touch the text area. The text will scroll once. Skipping a track (searching) 1. Touch the [{ (Track)] or [} (Track)] key during playback.
Precautions when preparing a disc Tag information (track title, artist name, and album title) can be displayed for an MP3/WMA/ AAC file containing the Tag information. This system supports the ID3 TAG version 1.x/ 2.x and WMA-TAG. Note: • For details of the DivX file mentioned below, see “DivX Operations” (page 35). Precautions on the MP3/WMA/AAC files ●General precautions • Files other than MP3/WMA/AAC format cannot be played. In addition, some files may not be played because of the encoding settings.
English ❏ Selecting the MP3/WMA/AAC mode Owner’s manual 1. Set a disc which the MP3/WMA/AAC files are recorded to the DVD player. The system will automatically read the disc data, change to the DVD mode (MP3/WMA/ AAC mode), and start playback after a while. See also “Setting/Ejecting a Disc” (page 17). WARNING • Audio files may be recorded at a higher volume level than desired. Increase the volume gradually from the minimal setting after playback has started.
Other various play functions When a title or name displayed on the screen is longer than the text area, you can confirm the entire text by scrolling it. 1. Displaying the text you wish to scroll, touch the text area. The text will scroll once. MP3/WMA/AAC files can be stored together with DivX files in a disc or folder. You can select whether such discs are regarded as MP3/WMA/ AAC discs or as DivX discs. 1. Touch the [Options] key. 2.
English Owner’s manual • DivX VOD (Video-on Demand files) that have authorization data can also be played. These files must be authorized on your PC beforehand using the DivX Registration Code displayed on the System tab screen under the General screen (see page 48). • Set the Frame Size to 640 u 480 or 320 u 240 pixels. • Set the Frame Rate to 30 or 15 fps. • Add a file extension “.AVI”, “.avi”, “.DIVX”, or “.divx” using single byte characters.
Showing the DivX mode screen You can change the screen size to suit to the playback film. • The factory default setting is “Full Wide”. 1. Touch the screen to display the DivX mode screen. 2. Repeat touching the [Full Wide/Cinema/ Normal/Wide] key until your desired screen size is selected. • This key shows the current screen size setting. [Full Wide]: The image is expanded so that the rectangle of the image fits to the screen (16:9). The aspect ratio of the image may be changed.
Switching Subtitles English Owner’s manual You can switch the subtitle language if the current DivX file has one or more subtitles. 1. Showing the DivX mode screen, touch the [Options] key. 2. Touch the [Subtitle] key during playback or pause. Each time you touch the key, you can switch among the subtitle language. • The number of subtitles recorded may differ depending on the DivX file. • Depending on the DivX file, switching may be impossible. • It may take time to switch the subtitle language. 3.
❏ Controlling the iPod Skipping a track (searching) ●iPod mode screen Play mode icons Fast forward and fast backward [Options] key [Music/Videos] key [Music/Videos] key: Switches the operation mode to the Video mode or Music mode. • Enabled in the Simple Control mode. List keys: Displays the corresponding list screen to select track to be played. [Videos], [Playlists], and [Music] are available. [Hide] key: Hides the iPod mode screen to display the playback picture. • Displayed only in the Video mode.
Other various play functions English Owner’s manual 1. Touch the [Options] key. 2. Touch a touch key of the function you want to play. 1-track repeat: Touch the [One] key of the Repeat item. • This operation plays back the current or selected track repeatedly. All repeat: Touch the [All] key of the Repeat item. • This operation plays back all the tracks currently selected repeatedly. Song shuffle: Touch the [Song] key of the Shuffle item.
1. Touch the desired Category key from the iPod mode screen to display the corresponding list screen. 2. Touch the desired item key on the screen to specify it. • Touch the [{] or [}] key to scroll the list. You can also use the ABC Search function to scroll the list (see below). • When a track list of an Album, Playlist, or Video Playlist is displayed, specifying a track starts playback of the specified album/ playlist from the specified track.
Selecting the Output Signal English Owner’s manual This setting is used to select the audio signal of video tracks. 1. Touch the [Options] key. 2. Touch the [Digital] or [Analog] key of the Output Signal item to specify the setting. [Digital]: The digital audio data via the USB will be output. Normally select this setting. [Analog]: The analog audio data via the AUX1 will be output. Select this setting if your iPod cannot output digital signals. 3. Touch the [Back] key to return to the previous screen.
The operations in the USB Memory mode are same as those in the MP3/WMA/AAC modes. See “Operating MP3/WMA/AAC playback” (page 34) for details. Note: • When performing the fast forward or fast backward function, the playback speed will become 10-time faster. For the VBR files, it may differ depending on the file. Navigation System Operations Notes on the Navi functions • Hereafter in this section, the Navigation system will be called as “Navi”.
Switching to another AUX mode English 1. Showing the AUX mode screen, touch the [AUX] key. The system will enter into another AUX mode. 7. SYSTEM SETTINGS Audio Settings Changing the audio input level Owner’s manual The input audio level of the AUX terminals can be changed. • The factory default setting is “High”. 1. Touch the screen to display the AUX mode screen, then repeat touching the [Sense] key to select the level.
This system provides 4 types of sound tone adjustment functions. You can select desired function and adjust the effect level. • The factory default setting is “Off”. 3-2. Touch the [BEQ1], [BEQ2], [BEQ3], [Custom], or [Off] key to select the function you wish to apply. [BEQ1]: The bass sound area is emphasized. [BEQ2]: The mid sound area is reduced, and the bass and treble sound area are emphasized. [BEQ3]: The mid sound area is lowered, and the bass and treble sound area are extremely emphasized.
English Owner’s manual 3-3. Touch the [{] or [}] key of the Fader item to adjust the fader level. [{]: Emphasizes the sound from the front speakers. [}]: Emphasizes the sound from the rear speakers. Adjustment range: front 12 to rear 12 • The factory default setting is “0”. ❏ Setting the Sub Woofer Control You can adjust the volume output to the Sub Woofer. • The factory default setting is “0”. 3-1. Touch the [Others] key to display the Others tab screen. 3-2.
3-1. Touch the [Others] key to display the Others tab screen. 3-2. Touch the [}] key to display the next screen. 3-3. Touch the [[] or []] key of the Audio ATT item to set the volume level when a voice interrupt arises. Settings: Mute, Low, Mid, High General Settings ❏ Displaying the General screen You can customize the various settings of this unit from the General screen. 1. Touch the [SET] key. The Settings screen appears. 2. Touch the [General] key. The General screen appears.
English ❏ Setting the Beep The sound heard when you make operations is called “beep”. The system can be set so that it does not produce this beep sound. • The factory default setting is “On”. Owner’s manual 3-1. Touch the [System] key to display the System tab screen. 3-2. Touch the [On] or [Off] key of the Beep item to turn the Beep function on or off.
You can select the speaker which the telephone calls are output. • The factory default setting is “Right”. 3-2. Touch the [}] key to display the next screen. 3-3. Touch the [Left] or [Right] key of the TEL Speaker item to select the speaker. Left: The telephone calls are output from the front left speaker. Right: The telephone calls are output from the front right speaker. ❏ Performing the System Check You can perform the system check by the following operation. 3-1.
English Owner’s manual When the ENTER PERSONAL CODE screen appears Adjusting the Monitor The Personal Code screen will be displayed when turning the ACC power on after performing the following operations: • The car battery was replaced. • The backup power was cut off. • The Reset button was pressed. You can customize the various monitor settings by the following operations. Note: • If you forgot your Personal Code, please consult your dealer or an authorized Clarion service center. 1.
English ❏ Adjusting the Dimmer, Bright, Color, Contrast, and Hue level Owner’s manual Note: • The Bright, Color, Contrast, and Hue settings can be adjusted only when a video image is displayed on the screen, and the car is stopped with applying the parking brake. • The Hue setting can be adjusted only when the NTSC mode is selected. • The navigation screen has own dimmer setting separately from the AV screen. The dimmer adjustment in a mode does not affect each other screen.
English 8. TROUBLESHOOTING If you have a problem with this system, check the following items to resolve it. See also our homepage (www.clarion.com) for additional information. Owner’s manual General Problem Cause Measure Power does not turn on. (No sound is produced.) Fuse is blown. Replace with a fuse of the same amperage. If the fuse blows again, consult your store of purchase. Incorrect wiring. Consult your store of purchase. Nothing happens when buttons are pressed.
DVD Player Measure Another disc is already loaded. Eject the disc before loading the new one. There is a foreign matter already in place. Eject the foreign matter forcibly. Disc is dirty. Clean the disc with a soft cloth. Owner’s manual Sound skips or is noisy. Cause English Problem Disc cannot be loaded. Disc is heavily scratched or Replace with a disc with no scratches. warped. MP3/WMA/AAC files are not encoded properly. Use MP3/WMA/AAC files encoded properly.
USB Devices English Problem USB device cannot be inserted. Owner’s manual USB device is not recognized. Cause Measure The USB device has been inserted with wrong direction. Reversing the connection direction of the USB device, try it again. The USB connector is broken. Replace with a new USB device. The USB device is damaged. Disconnect the USB device and reconnect. If the device is still not recognized, try replacing with a different USB device. Connectors are loose.
USB Devices Cause Measure The connected USB device If the USB device is frozen, disconnect it, reset it, is not supported. and reconnect it again. Error 3 (USB memory) An error occurred when Disconnect the USB device, and reconnect it controlling the USB device. again. Error 3 (iPod) The selected category has no track data. Touch the [{ (Track)] key. If the error is not cleared, disconnect the iPod, and reconnect it again. The iPod is frozen. Disconnect the iPod, reset it, and reconnect it again.
Video Output Video output: 1.0 r0.2 Vp-p (output impedance 75 :) LCD Monitor Frequency Range: 87.00 MHz to 108.
Installation Precautions WARNING Symbol Identification This manual uses symbols and icons to indicate safety precautions and concerns during the installation procedure. Be sure to carefully read and understand each precaution prior to beginning the installation. WARNING This symbol is intended to alert the user to the presence of important operating instructions. Failure to heed the instructions may result in severe injury or death.
Installation Notes English WARNING INSTALLATION MANUAL • Please note the position of pipes, tanks and electrical wirings before installing the unit into the vehicle; failure in avoiding these may cause a fire or malfunction. CAUTION CAUTION • Use only the supplied parts. If unspecified parts are used, they may cause damage. • Any holes made in the body of the vehicle should be sealed with a silicon adhesive. If exhaust fumes or water penetrates into the vehicle, this may cause an accident.
• Do not open the case. There are no userserviceable parts inside. If you drop anything into the unit during installation, consult your dealer or an authorized Clarion service center. • Prepare all articles necessary for installing the main unit before starting. • This model features an operation panel that slides forward. On some types of cars, the operation panel may make contact with the dashboard or gearshift lever, in which cause it cannot be installed.
English 5. INSTALLING THE MAIN UNIT INSTALLATION MANUAL This unit is designed for fixed installation in the dashboard. • When installing the main unit in NISSAN vehicles, use the parts attached to the unit and follow the instructions in Figure 6. When installing the main unit in TOYOTA vehicles, use the parts attached to the vehicle and follow the instructions in Figure 7. • Wire as shown in Section 9 (see page 64).
Installing the Main Unit in a TOYOTA Vehicle English Install by using parts attached to the vehicle. (Screws marked ★ are attached to the vehicle.) INSTALLATION MANUAL Main Unit 8-Hexagonal screw (M5 u 8) Mounting bracket (1 pair for the left and right sides) Center Panel *2 *3 Figure 7 Note: *2 Some panel openings are too small for the unit depending on the vehicle type and model. In such a case, trim the upper and lower sides of the panel frame by about 0.5 to 1.
English 6. REMOVING THE MAIN UNIT When the main unit is to be removed, disassemble it in the reverse of the order in “INSTALLTING THE MAIN UNIT” (see page 60). 7. CAUTIONS ON WIRING INSTALLATION MANUAL • Be sure to turn the power off before wiring. Be particularly careful where you route the wires. • Keep them well away from the engine, and exhaust pipe, etc. Heat may damage the wires. • If the fuse should blow, check to see if the wiring is correct.
WARNING Note: • The supplied GPS antenna is for installing inside the vehicle. Do not install it outside the vehicle. • Install the GPS antenna more than 50 cm away from the main unit, other audio devices such as CD player, and a radar detector. If it is installed near these devices, GPS reception may be impaired. • To improve the GPS signal reception, install the GPS antenna horizontally on a flat plane. • Do not wax or paint the cover of the GPS antenna.
English 9. WIRE CONNECTION Radio antenna jack iPod Aux2 audio input terminal Connector cable (included in your iPod) INSTALLATION MANUAL • Use the AUX1 audio input when you connect your iPod. • Connect the optional adaptor (BLT370) when you use your Bluetooth cellular phone. USB terminal or GPS antenna jack Steering wheel remote control terminal iPod with video Connector cable (CCA-723) Connect to the AUX1 audio/ video input terminal. Refer to the following page.
Black Purple/Black Red Gray Gray/Black White White/Black Brown Green Green/Black INSTALLATION MANUAL Purple +12V main power Ground Yellow 3A English Yellow No connection Rear right + Rear right +12V accessory Front right + Front right Front left + Front left Phone mute Rear left + Rear left - Blue/White Amplifier turn-on cord Orange/White Blue Illumination Auto antenna Grass-green Parking brake cord Purple/white Reverse gear cord See next page for how to connect the parking brake cord.
English ●Connecting the parking brake cord Connect the cord to parking brake lamp ground in the meter panel. INSTALLATION MANUAL Note: • Connecting the parking brake cord to lamp ground allows you to watch video images when the parking brake is engaged. • When the parking brake cord is not connected, the monitor will not display video images.
Clarion Co., Ltd. All Rights Reserved.Copyright © 2009: Clarion Co., Ltd.
