Clarion/Hyperlink Bridge Kit Installation Manual Rev. A Page 1 Hyperlink/Clarion M10II Extended Range Wireless LAN Bridge Kit Featuring the Clarion M10II 10 Mbit/sec Wireless Bridge Installation Manual Quick Installation Manual –Page 18 Copyright © 1996, Clarion Corporation of America. All rights reserved. No part of the contents of this document may be transmitted or reproduced in any form or by any means without the written permission of Clarion Corporation of America.
Clarion/Hyperlink Bridge Kit Installation Manual Rev.
Clarion/Hyperlink Bridge Kit Installation Manual Rev. A Page 4 WARNINGS The manufacturer assumes no responsibility for damage caused by interference due to this equipment. Radio Frequency Interference Statement USA - Federal Communications Commission (FCC): This device complies with Part 15 of FCC Rules. Operation of this device is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference that may cause undesired operation.
Clarion/Hyperlink Bridge Kit Installation Manual Rev. A Page 5 Introduction The Clarion M10II is a wireless transceiver providing 10 Mbit/sec burst data rate to support wireless connections in IEEE 802.3 and Ethernet II (TCP/IP) LAN. Equipped with a Hyperlink Extended Range Amplified Antenna System, the M10II offers an ultra high-performance long-range building-to-building network bridge. The M10II functions as an Ethernet MAU.
Clarion/Hyperlink Bridge Kit Installation Manual Rev. A Page 6 Types of Installations The type of application will determine which type of kit to install: Building-to-Building or Tower-to-Tower: Typically these installations will typically require directional Yagi or Grid Antenna kits. Central Node in a Multipoint Network or Mobile Network: This type of installation typically requires an Omni Directional Kit at the central node for 360 degree coverage.
Clarion/Hyperlink Bridge Kit Installation Manual Rev. A Page 7 complete plug-and-play solution for linking buildings in an outdoor environment. All you need to add is suitable masts or towers and some basic site planning. Please read this manual in its entirety before beginning the installation.
Clarion/Hyperlink Bridge Kit Installation Manual Rev. A Page 8 M10II Front and Rear Panel Features Internal antenna (inside of the top cover) MAU port MAU LED TX LED External antenna port RX LED Power LED DC 6.2V port Power Switch FCC Certification label (bottom) Hyperlink Technologies, Inc.
Clarion/Hyperlink Bridge Kit Installation Manual Rev. A Page 9 Connections and Features of the Amplified Antenna Familiarize yourself with the connections and features of the Amplifier Unit: Mounting Flanges: Two sets of mounting holes are provided on the amplifier’s mounting flanges for either mast mounting using the included U-bolts, or bolted directly to a bracket or other structure.
Clarion/Hyperlink Bridge Kit Installation Manual Rev. A Page 10 The DC Power Injector/ Lightning Protector The DC Power Injector (also known as a "Bias-T") is an in-line device which couples DC power onto a coaxial cable, enabling the cable to carry both RF (radio frequency) signals and DC power. The amplifier is powered remotely through the coaxial antenna feed cable by the way of this device. The DC Power Injector included with the kit also provides integral lightning protection.
Clarion/Hyperlink Bridge Kit Installation Manual Rev. A Page 11 Overall System Configuration The overall system configuration is shown below. Refer to this diagram while reading the section which follows, and during system installation. Transceiver AUI to 10BaseT JX-4000 Antenna Signal Filter DC Power Injector 10BaseT Cable Amplifier Antenna Cable 50ft. Adapter Cable 4ft. DC Power Supply Network Workstation Hyperlink Technologies, Inc.
Clarion/Hyperlink Bridge Kit Installation Manual Rev. A Page 12 ANTENNA SYSTEM CONNECTION Warning The M10II may only be operated using one of the approved antenna kits described herein. All antenna system components are equipped with unique connectors. Although these connectors may look similar to standard types they are not compatible with them. Attempting to attach standard connectors to system components can cause damage to the connectors and attached equipment.
Clarion/Hyperlink Bridge Kit Installation Manual Rev. A Page 13 Preparing for System Installation Warning: These antennas are designed to be mounted in open areas such as rooftops or building exterior walls. They are designed to be installed at least 6 feet away from areas occupied by people. During system operation, always keep the antenna at least 1 foot away from your head. Warning: Before performing the following steps make certain that there are not any power lines within 50 ft.
Clarion/Hyperlink Bridge Kit Installation Manual Rev. A Page 14 5. Attach the one end of the antenna ground cable to the antenna mounting bracket or V-bolt and the other end to a building ground. 6. Very carefully raise the mast and loosely secure it with the mast mounting hardware. Use the plastic wire ties to tie the antenna cable to the mast every six to twelve inches. 7. Aim the directional antenna in the direction of the building you will be linked to.
Clarion/Hyperlink Bridge Kit Installation Manual Rev. A Page 15 Basic System Checks Using the system’s diagnostic LEDs, some basic system checks can now be performed. When the power is applied to the amplifier, the Power/Transmit indicator LED (found on the bottom corner of the amplifier) glows green. the Power Indicator LED on the DC Power Injector/ Lightning Protector will also illuminate green. When the system is transmitting the amplifier’s LED flashes from green to red/orange.
Clarion/Hyperlink Bridge Kit Installation Manual Rev. A Page 16 M10II LED Diagnostic Display During power-up, the front panel LEDs on the M10II provide some diagnostic information. Refer to the table below for LED diagnostic information. Label MAU TX Color Green Red RX Green Power Red Description Indicates MAU signal (upload or download) is active. 1.
Clarion/Hyperlink Bridge Kit Installation Manual Rev. A Page 17 M10II Specifications Frequency Range: Carrier Frequency: Modulation Type: Chip Modulation: Processing Gain: Communication Method: Channel Access Method: Type of Interface: Datalink Interface: Network Addressing: RF MAC Protocol: 1. 1 Network Topology: 2400-2483.5 MHz ISM band 2436.07 MHz Direct Sequence Spread Spectrum BPSK, 32 Mcps 12dB (Nominal) Half Duplex SS-P-CSMA1 MAU (driven by AUI) IEEE802.
Clarion/Hyperlink Bridge Kit Installation Manual Rev. A Page 18 Clarion Quick Installation Manual A quick installation manual for Clarion Amplified and non-amplified systems. www.hyperlinktech.com Hyperlink Technologies, Inc.
Clarion/Hyperlink Bridge Kit Installation Manual Rev. A Page 19 MATERIAL LIST • • • • • • • • • • • • • (2) Clarion M10II Radios (2) Clarion Power Supplies (2) AT-MC12T-16 Transceiver (2) AT-MC12T-16 Power Supplies (2) Cat 5 cables 7 feet with RJ45 (2) Clarion Adapter Cables (2) Cables, 50 feet low-loss with integral lightning protection (2) 2.
Clarion/Hyperlink Bridge Kit Installation Manual Rev. A Page 20 Installation Hyperlink recommends that you use two computers directly off a working Network segment to test the operation before the installation of a long-range link. The following steps are for two computers that are off of a working network. Do not power up any equipment until all equipment is connected. 1. Connect the transceiver to the Clarion radio. 2. Connect the CAT 5 Patch cable from the transceiver to the computer network card. 3.
Clarion/Hyperlink Bridge Kit Installation Manual Rev. A Page 21 Power-up Please follow the the steps below to power up the equipment. 1. Power on the Clarion radio first. The power button on the front of the radio is not operational. When the power cord is inserted into the radio it will power up. The following is the LED sequence that should appear after you power up the radio (self-test).
Clarion/Hyperlink Bridge Kit Installation Manual Rev. A Page 22 1201 Clint Moore Road Boca Raton, FL 33487 Technical Support and Sales Web Site: www.hyperlinktech.com For technical support: support@hyperlinktech.com For Sales: sales@hyperlinktech.com Phone: 561-995-2256 Fax: 561-995-2432 Hyperlink Technologies, Inc.
