Owner's Manual
Table Of Contents
Basic Operations
When
"ON"
is
set:
8-®-CD·
Touch
[>]
key
to
enter
detail
setting
stage.
1\
8-®-®· Slide along
[S~RL]
slider
or
touch
[A]I[V]
key to select the value in sequence
of
"HIGH"
~
"MID"
~
"LOW"
* The factory default setting is "MID".
8-@. After completing settings, touch the [ENT]
key
to return to the 1
51
selected item.
•
Adjusting
the
balance
8-CD·
Select
"BALANCE".
8-®. Touch
[>]
key
to
enter
detail setting stage.
1\
8-®
Slide along [
S~RL]
slider
or
touch
[A)I[
V ]
key to adjust the balance of the right and left
speakers.
* The factory default setting is "CENTER".
(Adjustment range: RIGHT 12
to
LEFT 12)
&@.
After completing settings, touch the [ENT]
key to return to the 1
51
selected item.
•
Adjusting
the
fader
&CD.
Select "FADER".
8-@.
Touch [>]
key
to
enter
detail setting stage.
1\
8-®
Slide along [
S~RL]
slider
or
touch
[A
]/[
V]
key to adjust the balance of the rear and front
speakers.
* The factory default setting is "CENTER".
(Adjustment range: FRONT 12 to REAR 12)
8-@. After completing settings, touch the [ENT]
key to return to the 1
51
selected item.
•
Adjusting
the
M-BEX
&CD
Select "M-BEX".
8-®.
Touch
[>]
keY}El
enter
detail setting stage.
&®
Slide along [
S~RL
] slider
or
touch
[A
]/[
V]
key to turn on
or
turn off the
MAGNA
BASS
EXTEND
effect.
* The factory default setting is "OFF".
(Adjustment range: ON/OFF)
8-@. After completing settings, touch the [ENT]
key to return to the 1
51
selected item.
•
Adjusting
the
high
pass
filter
8-CD·
Select "HPF".
8-®.
Touch
[>]
key to
enter
detail setting stage.
1\
8-®.
Slide along [
SCRL
] slider
or
touch
[A]I[
V ]
key to select
th~
setting in sequence
"60"
~
"90"
~
"120"
~
"THROUGH"
* The factory default setting is "THROUGH".
*
This
is
supported
only
with
amplifiers
equipped with this function. Output is not
supported from RCA cables.
• Setting
the
subwoofer
You can set the low pass filter of subwoofer.
8-CD.
Select "S-W LPF".
8-®.
Touch [>] key to
enter
detail setting stage.
1\
8-®.
Slide along [
SCRL
] slider
or
touch
[A
]/[V ]
key to select
th~
setting in sequence
"THROUGH"
~
"60"
~
"90"
~
"120"
* The factory default setting is "THROUGH".
•
Adjusting
the
subwoofer
output
volume
You can adjust the volume output from the unit's
subwoofer output terminal.
This
adjustment can be performed only when the
"S-W LPF" is set to "60", "90"
or
"120".
8-CD
Select "S-W VOL".
8-®.
Touch [>]
key
W
enter
detail setting stage.
8-®. Slide along [
S~RL
] slider
or
touch
[A
]/[
V]
key
to increases
or
decreases the subwoofer
volume.
* The factory default setting
is
"0".
(Adjustment range: +6
to
-6)
* When the volume level is more than 30, the
subwoofer volume adjustment value can not
reach +6.
Note:
• During SOUND Adjustment mode,
if
no
operation
is
performed for more than 10 seconds, this mode
can be cancelled and return
to
previous mode.
FZl09 15