Owner’s manual AM/FM CD PLAYER • • Clarion Co., Ltd. All Rights Reserved. Copyright © 2003: Clarion Co., Ltd.
English Thank you for purchasing this Clarion product. ∗ Please read this owner’s manual in its entirety before operating this equipment. ∗ After reading this manual, be sure to keep it in a handy place (e.g., glove compartment). ∗ Check the contents of the enclosed warranty card and keep it carefully with this manual. ∗ This manual includes the operating procedures of the CD changer, MD changer and TV tuner connected via the CeNET cable.
Display Items Handling Compact Discs Operation status indication Titles, frequency, PS names, clock, etc. are displays. Preset channel indication (1 to 6) Disc number indication (1 to 12) Stereo indication : Disc indication : Scan indication : Mute indication : Enter indication 1. When the inside of the car is very cold and the player is used soon after switching on the heater moisture may form on the disc or the optical parts of the player and proper playback may not be possible.
/ 4. NOMENCLATURE [TITLE] button Note: • Be sure to read this chapter referring to the front diagrams of chapter “3. CONTROLS” on page 5 (unfold). Names of the Buttons and their Functions [CD SLOT] [ROTARY] [Q] [Z+] [SW-VOL] [ISR] [FNC] [A-M] [BND] [RELEASE] button [UP], [DN] buttons • Press the [RELEASE] button to unlock the DCP. • Select the disc. [ROTARY] knob • Store a station into memory or recall it directly while in the radio mode.
The control panel can be detached to prevent theft. When detaching the control panel, store it in the DCP (DETACHABLE CONTROL PANEL) case to prevent scratches. We recommend taking the DCP with you when leaving the car. Storing the DCP in the DCP Case Hold the DCP, in the orientation as shown in the figure below, and put it into the supplied DCP case. (Ensure the DCP is in the correct orientation.) DCP Removing the DCP 1. Press the [FNC] button for 1 second or longer to switch off the power. 2.
Mode Receiver for remote control unit Radio CD/MD changer DVD changer CD Button Switches among radio, CD, CD/MD changer, DVD changer, TV and AUX. [BAND] Switches reception band. Operating range: 30˚ in all directions Signal transmitter Remote control unit [FUNC] [ ],[ ] ] Increases and decreases volume (in all modes). [ ],[ ] Moves preset channels up and down. Moves tracks up and down. When pressed and held for 1 second: Fast-forward/fast-backward. Moves preset channels up and down.
Basic Operations Basic Operations Note:Be sure to read this chapter referring to the front diagrams of chapter “3. CONTROLS” on page 5 (unfold). CAUTION Be sure to lower the volume before switching off the unit power or the ignition key. The unit remembers its last volume setting. If you switch the power off with the volume up, when you switch the power back on, the sudden loud volume may hurt your hearing and damage the unit.
Radio Operations Adjusting the Z-Enhancer Plus FM reception Manual tuning Auto store 1. Press the [Z+] button and select the ZEnhancer Plus mode to adjust. 2. Press the [A-M] button and turning the [ROTARY] knob clockwise adjusts in the + direction; turning it counterclockwise adjusts in the – direction. ●When “B-BST 0” is selected, you can adjust the bass in the range of –3 to 3. ●When “IMPACT 0” is selected, you can adjust the bass and treble in the range of –3 to 3.
CD Operations CD Operations Insert a CD into the centre of the CD SLOT with the labeled side facing up. “LOADING” appears in the display, the CD enters into the slot, and the play starts. For CD (12 cm) For single CD (8 cm) CD SLOT Notes: • Never insert foreign objects into the CD SLOT. • If the CD is not inserted easily, there may be another CD in the mechanism or the unit may require service. • Discs not bearing the or mark and CD-ROMs cannot be played by this unit.
Operations Common to Each Mode Operations Common to Each Mode Adjusting the display contrast Setting the clock You can adjust the display contrast to match the angle of installation of the unit. 1. Press and hold the [TITLE] button for 1 second or longer to switch to the adjustment selection display. 2. Press the [a] or [d] button to select “CLOCK”. 3. Press the [ ] button. 4. Press the [a] or [d] button to select the hour or the minute. 5.
CD/MD Changer Operations CD/MD changer functions When an optional CD/MD changer is connected through the CeNET cable, this unit controls all CD/MD changer functions. This unit can control a total of 2 changers. Press the [FNC] button and select the CD(MD) changer mode to start play. If 2 CD(MD) changers are connected, press the [FNC] button to select the CD(MD) changer for play. ∗ If “NO MAG” appears in the display, insert the magazine into the CD changer.
TV Operations TV Operations Manual tuning Auto store Setting the TV area When an optional TV tuner is connected through the CeNET cable, this unit controls all TV tuner functions. To watch TV requires a TV tuner and monitor. There are 2 ways available: Quick tuning and step tuning. When you are in the step tuning mode, the frequency changes one step at a time. In the quick tuning mode, you can quickly tune the desired frequency. 1. Press the [BND] button and select the desired band (TV1 or TV2).
Fuse is blown. Incorrect wiring. General No sound output when operating the unit with amplifiers or power antenna attached. Nothing happens when buttons are pressed. If an error occurs, one of the following displays is displayed. Take the measures described below to eliminate the problem. Measure Replace with a fuse of the same amperage. If the fuse blows again, consult your store of purchase. Error Display Consult your store of purchase.
English 11. SPECIFICATIONS FM Tuner Audio Frequency Range: 87.
