Owner’s manual Mode d’emploi Manual de instrucciones DXZ865MP CD/MP3/WMA Receiver / CeNET & Touch Panel Control Récepteur CD/MP3/WMA / CeNET et écran de contrôle tactile Receptor de CD/MP3/WMA / Control en panel táctil y CeNet Clarion Co., Ltd. 2005/12 (Abe·Abe) All Rights Reserved. Copyright © 2005: Clarion Co., Ltd.
English Thank you for purchasing this Clarion product. ∗ Please read this owner’s manual in its entirety before operating this unit. ∗ After reading this manual, be sure to keep it in a handy place (e.g., glove compartment). ∗ Check the contents of the enclosed warranty card and keep it carefully with this manual. ∗ This manual includes the operating procedures of the CD changer and TV tuner connected via the CeNET cable.
1. When the inside of the car is very cold and the player is used soon after switching on the heater, moisture may form on the disc or the optical parts of the player and proper playback may not be possible. If moisture forms on the disc, wipe it off with a soft cloth. If moisture forms on the optical parts of the player, do not use the player for about 1 hour. The condensation will disappear naturally allowing normal operation. 2.
Motorized Face English This unit uses a MOTORIZED FACE to make large screen displays possible. When you use the MOTORIZED FACE, be sure to close it. CAUTION BE CAREFUL NOT TO GET YOUR FINGERS CAUGHT WHEN OPENING AND CLOSING THE MOTORIZED FACE. 1. For safety’s sake, always close the MOTORIZED FACE before leaving this unit unused for a prolonged period or switching OFF the ignition key. If you switch OFF the ignition key with the MOTORIZED FACE tilted, the MOTORIZED FACE does not close. 2.
English 3.
English 4. NOMENCLATURE Names of the Buttons and their Functions IR-Receiver [ROTARY] knob • Receiver for remote control unit. (Operating range: 30° in all directions) • Press the knob to turn the power ON. • Press the knob to turn the power OFF. • Turn the knob to adjust the volume. [ADJ] button • Use this button to set or adjust the various settings in the adjust mode. [CD SLOT] [Q] (OPEN/EJECT) button DCP Detaching Slider • Open/closes the control panel.
Operations when External Equipment is Connected to this Unit English ● When the CD/DVD changer is connected ∗ For details, see the section “CD changer operations” (cf. page 35). For the DVD changer, refer to the Owner’s Manual provided with the DVD changer. ● When the TV is connected ∗ For details, see the section “TV operations” (cf. page 38). ● When the Satellite Radio Receiver is connected ∗ For details, refer to the Owner’s Manual provided with the Satellite Radio Receiver.
Touch Panel Buttons English ● Standard operation display Left slide button Right slide button ● Simple operation display (To switch to the simple operation display, press and hold the [MODE] button for 2 seconds or longer.) Left button 98.10 FM1 Right button P3 P.CH SEEK PRESET BAND PS/AS 2:45 pm DISP FM1 P.CH SEEK Sub buttons 98.10 PRESET Left slide button • Touch this button for seek up/down or track up/ down operations.
Touch Panel Operations Touch Touch the display with your fingertip and take it away within 1 second. This is the most basic operation when operating the display. Touch Touch the display with your fingertip, and move your finger to the up ( ) or down ( ) with your fingertip still touching the display, and keep your fingertip on the display. The current operation continues for the time your fingertip is held on the display. This operation is used, for example, for fast-forwarding/fast-rewinding tracks.
English 5. DCP The control panel can be detached to prevent theft. When detaching the control panel, store it in the DCP (DETACHABLE CONTROL PANEL) case to prevent scratches. We recommend taking the DCP with you when leaving the car. Attaching the DCP 1. Place the DCP to the MOTORIZED FACE, adjusting the metal connecters on DCP and the MOTORIZED FACE. 2. Press the DCP until it clicks into the MOTORIZED FACE. Removing the DCP 1. Press the [Q] button to open the DCP. 2.
English 6. REMOTE CONTROL Receiver for remote control unit Operating range : 30° in all directions Remote control unit Signal transmitter [SRC] [BND] [ ] [ ], [ ] [a], [d] [MUTE] [DISP] [ISR] [RDM] [SCN] [RPT] Inserting the Battery 1. Turn over the remote control unit and slide the cover in the direction indicated by the arrow in the illustration. 2. Insert the battery (CR2025) into the insertion guides, with the printed side (+) facing upwards. 3.
English Functions of the Remote Control Unit Buttons Mode Radio/Satellite CD changer DVD changer CD/MP3/WMA Button TV [SRC] Switches among radio, Satellite Radio Receiver, CD/MP3/WMA, CD changer, DVD changer, TV and AUX. [BND] Switches reception band. Returns to the first track. Moves the next disc in increasing order. Switches reception band. [ ],[ ] Increases and decreases volume (in all modes). [ ],[ ] Moves preset channels up and down. Moves tracks up and down.
English 7. OPERATIONS Basic Operations CAUTION Be sure to lower the volume before switching the unit off or the ignition key. The unit remembers its last volume setting. If you switch the power OFF with the volume up, when you switch the power back ON, the sudden loud volume may hurt your hearing and damage the unit. Turning ON/OFF the power Selecting a mode 1. Press the [SRC] button to change the operation mode. 2.
Basic Operations English Switching the background 3. Touch on the left of the display to select [DAY] or [NIGHT]. 1. Touch [DISP]. COLOR SELECT NIGHT 98.10 FM1 P.CH SEEK PRESET BAND PS/AS on the left of the display to 2. Touch choose the background. DISPLAY EDIT 02 BGV RTN SP/ANA RTN 2:45 pm DISP ∗ DISPLAY EDIT screen displays. P ∗ The background includes 12 wallpaper images and 2 motion pictures. ∗ Choose [SCAN] to automatically display all the wallpaper.
Basic Operations English Switching the title display You can display stored information such as disc titles or track titles when playing back music in CD or CD changer mode. 1. Touch [DISP] while a title is shown. 01 TRACK 02:53 2:45 pm TOP DISP ∗ Display edit mode appears. 2. Touch [TITLE]. DISPLAY EDIT P 1 05 BGV TITLE D-BLUE LOW COLOR SENS SPE/ANA RTN ∗ Title edit mode appears. on the right of the display to 3. Touch choose the kind of title to show.
Radio Operations English Screen displays in the radio mode ● Standard operation display The standard operation display appears by pressing the [SRC] button and selecting the radio mode. Preset No. display Title display Reception Frequency band display display 98.10 FM1 P3 BAND Touching this switches the reception band. Touching and holding this for 1 second or longer switches between the manual tuning mode and the seek tuning mode. PS/AS Touching this starts a preset scan.
Radio Operations Preset memory Seek tuning is a function for automatically tuning stations with good reception. A total of 24 preset positions (6-FM1, 6-FM2, 6FM3, 6-AM) exists to store individual radio stations in memory. 1. Touch and hold [BAND] for 1 second or longer if “MANU” is displayed. Automatic tuning is possible when “SEEK” is displayed. 2. Touch on the frequency display. “SEEK UP”/“SEEK DOWN” is displayed, and tuning starts. Tuning automatically stops at stations with good reception.
Radio Operations English ■ To cancel preset scan 1. Touch [PS/AS]. “P-SCAN” display disappears and the stations that were being received when [PS/ AS] was touched are received next. Instant station recall (ISR) Instant station recall is a special radio preset that instantly accesses a favorite radio station at a touch of a button. The ISR function even operates with the unit in other modes. • The factory default setting is “FM87.9MHz”. 1. Press the [ISR] button. “ISR” appears on the display.
CD/MP3/WMA Operations ● Standard operation display The standard operation display appears by pressing the [SRC] button to select the CD/MP3 mode. Track No. display Title display Folder No. display MP3 (WMA) MP3 01 Don , 01 t Stop Be TRACK FOLDER 01:01 2:45 pm DISP TOP DISP TOP Playing time display ● Simple operation display Pressing and holding the [MODE] button for 2 seconds or longer switches the simple operation display.
CD/MP3/WMA Operations English Precautions when creating MP3/WMA disc ● Default value is “CD”. ● Usable sampling rates and bit rates: 2. Touch [Å]/[Î] to go to the next page. 1. MP3: Sampling rate 11.025 kHz-48 kHz, Bit rate: 8 kbps-320 kbps / VBR 2. WMA: Bit rate 48 kbps-192 kbps ● File extensions 1. Always add a file extension “.MP3” or “.WMA” to MP3 or WMA file by using single byte letters.
CD/MP3/WMA Operations Selecting a track You can eject a disc by pressing the [Q] button even if the engine key or ACC is at the OFF position. When a CD-R/CD-RW recorded with an MP3 file or a WMA file is loaded, you can select only tracks recorded to the same folder by touching on the track display. CAUTION When the disc is ejected, press the [Q] button to close the control panel. If the control panel is left open, you will hear a double beep, and the control panel automatically closes. 1.
CD/MP3/WMA Operations English 2. Touch [Å]/[Î] to go to the next page. 3. Touch [PLAY LIST]. Notes: • The SCN/RPT/RDM functions cannot be used while in the play list mode. • The title changes from folder name to play list name. ∗ Scan play starts from the next track after the track currently being played. ■ To cancel scan play 1. Press the [MODE] button.
CD/MP3/WMA Operations English ■ To cancel random play 1. Press the [MODE] button. Folder random play This function allows you to play all folders on the disc at random. 1. Press the [MODE] button. 2. Touch [FOLDER RDM]. ■ To cancel folder random play 1. Press the [MODE] button.
Sound Adjustment English Adjustment items You can adjust a sound effect or tone quality to your preference. Anti Distortion Filter (ADF) .................... Page 24 MAGNA BASS EXTEND ....................... Page 24 Sub-woofer speaker volume (SW VOLUME) ................................. Page 25 Bass setting (BASS) ............................. Page 25 Treble setting (TREBLE) ....................... Page 25 Balance (BALANCE) ............................. Page 25 Fader (FADER) ...............................
Sound Adjustment Adjusting the treble (Gain, Frequency) Adjusting the sub-woofer 1. Press the [SOUND] button. • "SW VOLUME" (sub-woofer) can be adjusted only when the "SUB-WOOFER" is set to "ON" (cf. page 32). • The factory default setting for SW VOLUME is “0”. 1. Press the [SOUND] button. 2. Touch [SW VOLUME]. SW VOLUME 0 RTN 3. Touch on the right of the display and adjust the item as desired. ∗ This item can be adjusted within the range -5 to +5. 4.
Sound Adjustment English Adjusting the filter frequency Filter frequency You can set a filter frequency value best suited for your speakers. * This item can be adjusted only when “SUBWOOFER” is set to “ON”. • The factory default setting for FILTER is “THROUGH”. Filter adjustment ● SUB-W LPF (Subwoofer Low-Pass Filter) adjustment This filter cuts the signals above the selected frequency value. Each touch switches the frequency value as follows: THROUGH ➜ 50Hz ➜ 80Hz ➜ 120Hz ➜ THROUGH...
Common Operations The “TITLE INPUT” screen appears when you enter a title. Title TEXT FONT display display display Me I o d y 1. Either receive the radio or TV station, or play a CD for which you want to enter the title. 2. Touch [DISP]. a-Z FONT DISPLAY EDIT TEXT P RTN MEMO / RTN FONT display A : Capital alphabet letters a : Small alphabet letters 1 : Numbers : Symbols Ā : Umlaut Title display The currently entered title is displayed. TEXT display to select the character to enter.
Common Operations English ■ When a new title is stored beyond the maximum number of titles In the case of a radio or TV station Titles not stored to preset channels and ISR (radio stations only) are automatically cleared, and the new title is stored in memory. In the case of a CD Titles of CDs that have been played the least are cleared, and the new title is stored in memory. 4. When “ENT” is displayed at the right of the display, touch [ENT] to switch to the adjustment details display. 5.
Common Operations English ● Setting items Main item APPEARANCE SOUND TUNER SETTING Sub item CLOCK EDIT • Clock setting (cf. page 30) MSG INFO • Setting the message display ON/OFF (cf. page 30) MSG INPUT • Message information input (cf. page 30) DIMMER IN • Auto-dimmer setting (cf. page 31) DMR LEVEL • Setting the dimmer level (cf. page 31) BRIGHT • Adjusting the display brightness (cf. page 31) BLINK LED • Making the LED blink when DCP is removed (cf. page 31) BEEP • Setting beep (cf.
Common Operations English Setting the clock (CLOCK) When the power is OFF, the clock is displayed. The clock is displayed in 12-hour format. 3. Touch on the left of the display to select "MSG INFO". ADJ APPEARANCE MSG INFO OFF 1. Press the [ADJ] button. RTN 2. Touch [APPEARANCE]. on the left slide button to select 3. Touch “CLOCK EDIT” and touch [ENT]. ADJ APPEARANCE CLOCK EDIT [ ENT ] 4. Touch on the right of the display to select “ON” or “OFF”. 5.
Common Operations This function allows you to dim the lighting of the display matched to the illumination or the brightness inside your car. Select either “AUTO” (interlocked to the brightness inside your car) or “ILLUMI” (interlocked to the illumination inside your car) as the auto-dimmer setting. • When the auto-dimmer function is set to “AUTO”, the brightness of the display is dimmed according to the brightness detected by this sensor. • Set the dimmer setting at DMR LEVEL.
Common Operations English Setting the beep for when buttons are operated (BEEP) 1. Press the [ADJ] button to set to the adjust mode. The short or long high-pitched tone you hear when a button is operated is called a “BEEP”. • The factory default setting is “ON”. 3. Touch on the left of the display to select “SRC ICON”. 1. Press the [ADJ] button to set to the adjust mode. 2. Touch [APPEARANCE]. ADJ APPEARANCE SRC I CON I CON 2. Touch [APPEARANCE]. RTN on the left of the display to 3.
Common Operations 3. Touch on the left of the display to select "AUX SENS". ADJ SETTING ADJ SOUND AMP CANCEL OFF AUX SENS MID RTN 4. Touch on the right of the display to select “ON” or “OFF”. 5. Press the [ADJ] button to return to the original mode. Displaying the Satellite ID No. (SID DISP) • This item can be set only when Satellite Radio Receiver is connected. 1. Press the [ADJ] button to set to the adjust mode. 2. Touch [TUNER]. 3. Touch on the left of the display to select “SID DISP”.
Common Operations English Using the security function (CODEMATIC) This function prevents persons who do not know the touch sequence from easily operating this unit. The Touch Code display appears when DCP is attached and the power is turned ON with “CODEMATIC” set to “ON”. If you touch the display in this screen in the preset order, “SUCCESSFUL” is displayed and the power is turned OFF.
English 8. OPERATIONS OF ACCESSORIES CD Changer Operations CD changer When an optional CD changer is connected through the CeNET cable, this unit can control CD changer operations. This unit can be connected to a total of 2 CeNET-wired CD changers. ■ When 2 CD changers are connected Press the [SRC] button to select the changer connected to this unit. (Each press of the [SRC] button switches the changer.
CD Changer Operations English Selecting the changer mode Fast-forward/fast-rewind 1. Press the [SRC] button to select the changer mode. ∗ Each time you press the [SRC] button, the display switches as follows: Radio ➜ (Satellite) ➜ CD/MP3 ➜ (CD changer) ➜ (DVD changer) ➜ (TV) ➜ AUX ➜ Radio... 1. To fast-forward, touch display. ∗ The mode of equipment that is not connected is not displayed. Play starts automatically when the mode changes to the changer mode.
CD Changer Operations English Disc repeat play After all the tracks on the current disc have been played, disc repeat play automatically replays the current disc over from the first track. This function continues automatically until it is canceled. 1. Press the [MODE] button. 2. Touch [DISC RPT]. ■ To cancel disc repeat play 1. Press the [MODE] button. Random play Random play selects and plays individual tracks on the disc in no particular order.
TV Operations English TV tuner function When an optional TV tuner is connected through the CeNET cable, this unit controls all TV tuner functions. To watch TV, you need a TV tuner and a monitor. Screen displays in the TV mode ● Standard operation display The standard operation display appears by pressing the [SRC] button to select the TV mode. Reception Channel display band display Preset No. Title display display TV1 3ch MANU 2:45 pm PRESET BAND PS AS DISP DISP PRESET SEEK/MANU indicator P1 P.
TV Operations Preset memory Seek tuning is a function for automatically tuning stations with good reception. A total of 12 TV stations can be stored (6-TV1 and 6-TV2). This allows you to select your favorite TV stations and store them in memory for later recall. 1. Touch and hold [BAND] for 1 second or longer while “MANU” is displayed. Automatic tuning is possible when “SEEK” is displayed. 2. Touch on the channel display. “SEEK UP/SEEK DOWN” is displayed, and tuning starts.
TV Operations English ■ To cancel the preset scan 1. Touch [PS/AS]. “P-SCAN” disappears, and the stations that were being received when [PS/AS] was touched are received next. Watching a video The TV tuner has a VTR input terminal to which 1 external device can be connected. Connect a 12 V video cassette player (VCP) or video cassette recorder (VCR) to the TV tuner input terminal. 1. Press the [MODE] button. 2. Touch [TV/VTR]. ∗ Every time you touch this, the function switches between TV and VTR.
General Problem Cause English 9. IN CASE OF DIFFICULTY Measure Power does not turn on. (No sound is produced.) Fuse is blown. Replace with a fuse of the same amperage. If the fuse blows again, consult your store of purchase. Incorrect wiring. Consult your store of purchase. No audio when operating the unit with amplifiers. Amplifier turn-on lead is Turn the unit off and check each wire for a possible shorted to ground or short.
English CD/MP3/WMA Problem 42 Cause Measure Sound is bad directly after power is turned on. Water droplets may form on the internal lens when the car is parked in a humid place. Let dry for about 1 hour with the power on. Wrong filename File system is not correct. Use ISO9660 level 1, 2 or JOLIET or Romeo file system. File name or extension is not correct. Use alphanumeric/ASCII characters for MP3/WMA file name. Use “.M3U” for the file extension of a play list. Play list play is not performed.
English 10. ERROR DISPLAYS If an error occurs, one of the following displays is displayed. Take the measures described below to eliminate the problem. General DVD changer CD changer CD/MP3/WMA Error Display Cause Measure ERROR 2 A DISC is caught inside the CD deck and is not ejected. This is a failure of CD deck’s mechanism and consult your store of purchase. ERROR 3 A DISC cannot be played due to scratches, etc. Replace with a non-scratched, non-warped-disc.
English 11. SPECIFICATIONS FM Tuner Audio Frequency Range: 87.9 MHz to 107.9 MHz Usable Sensitivity: 9 dBf 50dB Quieting Sensitivity: 15 dBf Alternate Channel Selectivity: 70 dB Stereo Separation (1 kHz): 32 dB Frequency Response (±3 dB): 30 Hz to 15 kHz Maximum Power Output: 212 W (53 W × 4 ch) Bass Control Action (50 Hz): +16, -12 dB Treble Control Action (12.
English DXZ865MP 45 280-8336-00
Owner’s manual Mode d’emploi Manual de instrucciones DXZ865MP CD/MP3/WMA Receiver / CeNET & Touch Panel Control Récepteur CD/MP3/WMA / CeNET et écran de contrôle tactile Receptor de CD/MP3/WMA / Control en panel táctil y CeNet Clarion Co., Ltd. 2005/12 (Abe·Abe) All Rights Reserved. Copyright © 2005: Clarion Co., Ltd.
