Owner`s manual

Sound Adjustment
Sound effects and tone can be adjusted as
desired.
To change sound settings
1. Press the [SOUND] button to switch to the
sound adjustment display.
* The factory default sound setting is "Z-
EHCR+".
2. Press [~] or [~] to select the sound
adjustment mode.
Each time [~] or [~] is pressed, the
sound adjustment mode changes as
follows:
"Z-EHCR+"
+--+ "BASS" +--+ "TREBLE" +--+
"BALANCE" +--+ "FADER" +--+ "NF VOL"
* When "ENT" is flashing in the display, press
the
[ENT] button to adjust the setting value.
~III
* The sound adjustment mode is displayed
for 2 seconds before showing
the sound
setting.
3. Turn the [ROTARY] knob to adjust the
selected audio mode.
4. After completing settings, press the
[SOUND] button to return to the previous
mode.
• Setting the Z-Enhancer Plus
This unit has 4 sound tone effects stored in
memory.
Select the effect you prefer.
* The factory default setting is "OFF".
2-1. Select "Z-EHCR+".
3-1. When you turn the [ROTARY] knob, the
tone effect changes as follows:
"OFF"
+--+ "B-BOOST' +--+ "IMPACT" +--+
"EXCITE" +--+ "CUSTOM"
OFF : No sound effect
B-BOOST : Enhanced bass
IMPACT : Enhanced bass and treble
EXCITE : Enhanced bass, mid, and
treble
CUSTOM : User customized
When set to "B-BOOSTIIMPACT/EXCITE":
3-2. Press the
[;71~] button.
3-3. Turn the [ROTARY] knob to adjust the
setting (Setting range:
-3 to +3).
* The factory default setting is "0".
3-4. Press the [;71~ ] button to return to the
previous mode.
When
set to "CUSTOM":
3-2. Press and hold the [;~~] button (1 sec.).
Bass/treble characteristics become flat and
"FLAT' is show in the display.
3-3. Turn the [ROTARY] knob to change to the
"OFF" mode.
• Adjusting the bass
This adjustment is supported only when
Z-Enhancer Plus is set to "CUSTOM".
2-1. Select "BASS".
3-1. Press the
[;71~] button.
3-2. Press
[~] or [~] to change and select
settings as follows:
"B<G 0>"
+--+ "B<F 60>" +--+ "Q 1"
3-3. Turn the [ROTARY] knob to adjust values
for gain, F (center frequency) and Q curve.
B<G 0> :The factory default setting is "0".
(Adjustment range:
+7 to -7)
B<F 60> :The factory default setting is
"60".
(Adjustment range:
60/80/100/200)
Q 1 :The factory default setting is "1".
(Adjustment range: 1/1.25/1.5/2)
3-4. Press the
[;71~] button to return to the
previous mode.
• Adjusting the treble
This adjustment is supported only when
Z-Enhancer Plus is set to "CUSTOM".
2-1. Select ''TREBLE''.
3-1. Press the
[;71~] button.
3-2. Press
[~] or [~] to change and select
settings as follows:
"T<G 0>" +--+ "T<F 10K>"
3-3. Turn the [ROTARY] knob to adjust values
for gain and F (center frequency).
T<G 0> : The factory default setting is "0".
(Adjustment range:
+7 to -7)
T<F 10K>: The factory default setting is
"10K".
(Adjustment range:
101</12.51</
151</17.5K)
3
-4 Press the
[ENT] button to return to the
• ~/II
previous mode.
CZ209
9