Owner’s Manual / Mode d’emploi Benutzer-Handbuch / Manuale utente Handboek / Manual de usuario Ägarehandbok / Manual do Utilizador BLT433 CM-HS1/TEL003
English FCC Statement This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Français Déclaration FCC Deutsch FCC-Erklärung Ce dispositif est conforme à la section 15 du règlement de la FCC.
Contents 4 What is CM-HS1 5 Installation Installing CM-HS1 Fix CM-HS1 to the car sun visor Fix CM-HS1 to the dashboard 6 7 7 Pairing your CM-HS1 Introduction to Bluetooth® “pairing” Pairing the module 8 8 Using your CM-HS1 Operating Modes Connection Making a call Calling with the phone’s keypad Calling with the module using voice commands Ending a call Answering a call To reject a call To turn off the microphone Transferring a call Call-waiting Adjusting the volume Using headset and car handsfree 10
What is included in this package? English Your BLT433 Car Hands Free Kit includes: CM-HS1 Module Visor Clip CE-NET Convertor Box (TEL003) Visor Clip Mounting Screw External Microphone Note 4 Please check for the correct accessories before attempting to install BLT433 in your car, please refer to the Wiring & System Diagram (Page 17) section for more details.
Getting to know your module English What is CM-HS1? The CM-HS1 is a Bluetooth® car kit that offers a high quality Bluetooth® wireless connection for in-car use and utilises your car’s built-in audio system. This module works with any Bluetooth® mobile phone that supports the Bluetooth® Headset profile version 1.1 or Handsfree profile version 1.0.
Installation English Installing CM-HS1 It is important that the module is installed with the internal microphone facing towards the user. Use the Visor Clip to fix the module to the car sun visor, and route the main cable properly. (shown in Fig. 2) Use the given mounting screws to tighten the module (shown in Fig. 1) to the Visor Clip if necessary. If installing the module anywhere else, care must be taken in order not to damage the connector of the unit. (shown in Fig.
Installation English Fix CM-HS1 to the car sun visor Fig. 2 Fix CM-HS1 to the dashboard Fig.
Pairing your CM-HS1 English Introduction to Bluetooth® “pairing” With a Bluetooth® mobile phone, you must ‘pair’ the module with the phone before you use it for the first time. ‘Pairing’ creates a unique wireless link between the Bluetooth® phone and your module eliminating the need to repeat the pairing process during future use. The Bluetooth® function in your phone has to be turned on to establish automatic connection.
Pairing your CM-HS1 English 3. a) Press together , once if choose handsfree profile. (Blue and Red LED fast blinking alternately) b) Press together , twice if choose headset profile. (Blue and Red LED slow blinking alternately) 4. Your mobile phone will display once it detects the device. a) HF - CMHS1 - HF (Handsfree profile). b) HS - CMHS1 - HF (Headset profile). 5. Confirm the pairing device and the passkey or PIN is ‘0000’ and you’re successfully pair the module. 6.
Using your CM-HS1 English Operating Modes Once the CM-HS1 has been paired to a phone, it will enter either Listening or Connected mode. In Listening mode the CM-HS1 will be available to establish a connection to any of the paired devices in response to an incoming call. This is typical of phones connected as a Headset. In Connected mode, the CM-HS1 is connected to a particular phone and communication to another paired phone is not possible.
Using your CM-HS1 If your phone support voice-activated dialing, you can use this feature with your module. Note that voice-activated dialing on your phone must be enabled and voice tags (name and commands) previously stored. (Please refer to the phone’s user documentation for instructions on storing voice tags.) 1. Briefly press the “Answer” button on the module. 2. After the tone, say the name of the person you wish to call. 3.
Using your CM-HS1 English Answering a call Whenever your car stereo is operating, the hand free module is in standby mode awaiting the next call with the Blue LED showing, when an incoming call arrives the car stereo is mute automatically and the ring tone is reproduced through your car’s speaker. To answer the call press the “Answer” button on the module and speak normally. Your may also answer the call by using your phone’s answer keypad.
Using your CM-HS1 Some mobile phones allow you to accept another incoming call while you are using your module. This feature varies, dependent on mobile service provider and phone model. If you normally hear a beep on your mobile phone, you will still hear this beep through your car speaker or external speaker. If your phone’s service support this feature, you can use either your phone’s keypad or your module.
Understanding the CM-HS1 indicators English CM-HS1 provides indications of pairing and calling status as described in the following table.
Understanding the CM-HS1 indicators Action Name Connected (Service) Connected Ringing LEDs On Flash off @2s On Control Consequence Duration Off Call Short Start voice activated calling Call Long Return to Listening mode Call Short Start voice activated calling Call Long Return to Listening mode Call Short Accept call Call Long Reject call Volume-Up Short Increase speaker volume Volume-Down Short Reduce speaker volume Off Short on @ s Voice Dailing On On Call Active (Mic
Understanding the CM-HS1 indicators English Mode Action Name LEDs Call Active (MIcrophone Mute) Call Avtive on Phone Phone Audio On On On Control Consequence Duration Volume-Down Short Reduce speaker volume Volume-Up Long Mute microphone Volume-Down Long Mute microphone Call Short Clear call Call Long Transfer call to mobile Volume-Up Short Increase speaker volume Volume-Down Short Reduce speaker Volume Volume-Up Long Un-mute microphone Volume-Down Long Un-mute microph
Wiring Diagram (TEL003) English To car stereo telephone mute line To CM-HS1 CE-NET in CE-NET out BLT433 17
Specifications (CM-HS1) English Transfer standard Bluetooth® 1.0B/1.1, conforms to profile Frequency range 2.402~2.
Specifications (TEL003) 14.4V DC (10.8~15.6V allowable) negative ground Max. Current 5A Speaker Impedence 4Ω (4Ω~8Ω allowable) Max Output Power 6W Max Switching Input 50W Distortion Less than 0.05% S/N Ratio More than 85dB Frequency Response 30Hz ~ 15kHz (±3dB) Dimensions Approx. 84 x 63 x 25mm English Power supply voltage Please refer carefully to the system diagram before installing your BLT433.
Troubleshooting English This section lists some problems that you might encounter while using your car handsfree. See your phone owner’s manual for configuration. Cannot pair the car handsfree with the phone The Bluetooth® function in your phone must be set to Automatic or On. Your phone should be inside the car during the pairing procedure. The car handsfree must be on.
Additional information English Safe and efficient use Note: Read this information before using your Bluetooth® car handsfree. Changes or modifications to this Bluetooth® car handsfree not expressly approved by Clarion may void the user’s authority to operate the equipment. Please check for any exceptions, due to national requirements or limitations, in usage of Bluetooth® equipment before using this product. Product care Do not expose your product to liquid or moisture or to humidity.
Additional information English Installation Please note that only authorised personnel should install the Bluetooth® car handsfree. Please check with your car dealer for recommendations on professional installation engineers. Check with your car manufacturer’s representative to be sure that all equipment for the Bluetooth® car handsfree, including additional accessories, is placed in a safe location.
Additional information Electronic equipment Most modern electronic equipment is shielded from RF energy. However, certain electronic equipment is not, therefore: Do not use your Bluetooth® car handsfree near medical equipment without requesting permission. If you are using any personal medical devices, e.g. a pacemaker or a hearing aid, please read in your mobile phone’s User’s Guide for further information.
Additional information English Emergency calls IMPORTANT! This Bluetooth® car handsfree and the electronic device connected to the handsfree operate using radio signals, cellular and landline networks as well as userprogrammed functions, which cannot guarantee connection under all conditions. Therefore you should never rely solely upon any electronic device for essential communications (e.g. medical emergencies).
EC Declaration of Conformity We : Clarion Europa GmbH Hessenring 19-21, 64546 Mörfelden-Walldorf, Germany. declare under our sole responsibility that the following Product(s) Model : Bluetooth® Car Hands free Kit Part No(s) : CM-HS1 is (are) in conformity with the following relevent harmonised standards: EN300328-2 (2001-12) - Electromagnetic compatibility and radio spectrum matters (ERM); Wideband Transmission systems operation in the 2.4GHz ISM band. Part 2 Essential requirements under Article 3.
Clarion BLT433 English This manual is published by Clarion, without any warranty. Improvements and changes to this manual necessitated by typographical errors, inaccuracies of current information, or improvements to programs and/or equipment, may be made by Clarion at any time and without notice. Such changes will, however, be incorporated into new editions of this manual. The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc.
280-8282-01 back cover
