Owner s manual & Installation manual CJ-7500E 7 WATERPROOF WIDESCREEN DIGITAL QUAD COLOR MONITOR
CONTENTS １．SAFETY INSTRUCTIONS ....................................................................................................... 3 4 ２．BEFORE USE ..................................................................................................................................... 5 ３．FEATURES ......................................................................................................................................... 6 ４．CONTENTS ..............................................................
1. SAFETY INSTRUCTIONS Please read the “Safety Rules” carefully before using this product. Following the safety rules prevents users from damages related with the misuse of the product. It is very important to follow these safety rules. We state “Caution” and “Warning” to clarify any potential risk of damage associated with the misuse of the product. WARNING This information is for preventing bodily harm or even death and user should follow these safety rules.
CAUTION ● Disconnect battery before installation. Re-connect once installation is complete. Prevents electric shock or short circuit. ● Do not use for long periods without engine running. It may cause battery to go flat. ● The rear-view monitor image has the same right-left inversion as your vehicle s rearview mirrors. Depending on the vehicle, the field and angle of view may differ. ● Do not use multi socket or extended adaptor. It may cause unexpected overheating, fire and malfunction.
２. BEFORE USE Precautions (when you use the monitor) ● Use the product at the temperature range of -10℃ 60℃. ● Screen may be a little dark when the product is operated in low temperature areas. Screen will show normal luminosity after a few minutes. ● Do not disassemble and modify the product in any way. This may cause fire and/or electric shock. ● When you install the product in a vehicle and watch the monitor, the car engine should be running to avoid flattening the battery.
３. FEATURES ・7 WVGA (800x480) LCD panel ・Water resistant (IP67), Aluminum housing ・8 language display selection (English-French-German-Italian-Spanish-Swedish-Chinese-Japanese) ・DC12∼24V ・Max.4 camera input ・Camera input screen inversion (Normal/Mirror mode) ・User can choose split screen (2/3/4 Split screen) ・Dimmer sensor is built-in ４. CONTENTS * When opening the gift box, please check the contents listed below. If you find parts are missing, please contact place of purchase.
５. BUTTON FUNCTIONS [Monitor] ①② ③ ④ ⑤ ⑥ 1. DIMMER SENSOR Automatic brightness control sensor 2. DIM DIMMER 3. MODE Switch Screen / Select SUB-MENU 4. DOWN/UP/LEFT/RIGHT 5. MENU Switch Main Menu 6.
６. FUNCTIONS 1 POWER ON/OFF Press [ ] button then the picture from the cameras will be shown on the monitor. Press [ ] button again to switch off. * If there is no camera video input, the screen will remain Black. * Factory default setting shows 4 way split screen. CAM1 CAM4 CAM2 CAM3 2 VOLUME CONTROL Press [ ] button to control volume(0~100). Volume control works only in CAM1 screen. * Factory default Volume setting is 30.
4 SELECT SPLIT MODE Each split screen has two options. In split mode, press [ options. ] button then the screen switches between both 2 split screen 3 split screen 4 split screen 2 split screen 3 split screen 4 split screen 5 CAMERA SELECTION 1) FULL SCREEN MODE In full screen mode, press [ ] button then the screen switches in the following order. CAM 1 CAM 2 CAM 4 CAM 3 Press [MENU] button, then it displays screen information (Input mode / Volume).
2) 2 SPLIT SCREEN MODE Press [MENU] button to go to「SPLIT SCREEN SETUP」. SPLIT SCREEN SETUP SELECT INPUT SET LEFT SET RIGHT Please select the camera position (left or right) by using [ ] button. CAM2 CAM 1 CAM 2 CAM 3 CAM 4 Then press [ ] button to go to 「SELECT INPUT」. Please select the camera by using [ ] button. Then press [ ] button to save your selection. 3) TRIPLE SPLIT SCREEN MODE Press [MENU] button to go to「TRIPLE SCREEN SETUP」.
6 CAMERA MIRROR/NORMAL MODE SETTING 1) CAM1 full screen MIRROR SET CAM1 MARKER SETUP ON OFF Press [MENU] button. Press [MENU] button. CAM1 CAM2 CAM3 CAM4 MIRROR MIRROR NORMAL MIRROR Select camera with [ ] button and then press [ ] button to select Normal / Mirror view. 2) CAM2 or CAM3 full screen MIRROR SET CAM2 CAM2 TRIGGER SETUP FULL SCREEN SPLIT SCREEN Press [MENU] button. Press [MENU] button.
7 ON SCREEN DISTANCE MARKER SETTING Warning • The onscreen distance markers should be considered as a general reference to assist the driver in assessing the distances depicted on the screen. The distance markers have been designed based on the “CCD camera installation conditions” listed in the next section, but differences in vehicle design and construction may result in the actual installation condition or location being different from the conditions listed.
2) MARKER ADJUSTMENT (Adjusting the bumper position) - Press [MENU] button five times, and select MARKER ADJUST menu. - Press [ ] button, and select H / V. (H: horizontal / V: vertical ) - Press [ ] button, and switch marker pattern. (H = -12 ~ +12, V = -12 ~ +12, Default setting: H = 0, V = 0) - After 10 seconds, set up screen disappears, and set up finishes. * If there is no button operation, set up screen disappears even during set up process.
2) In case of TRG2 (Left turn signal) or TRG3 (Right turn signal), you can choose full screen or split screen by OSD setting. * This function is for showing not only Left(Right) but also rear view together at the same time, regardless of former screen status. It displays CAM2(3) and CAM1 as split screen when TRG2(3) signal input is on. CAM2 CAM2 CAM1 CAM2 TRIGGER SETUP FULL SCREEN SPLIT SCREEN In CAM2 full screen, press [MENU] button to see OSD.
4) In case of a hazard flasher trigger(TRG2+TRG3), the monitor displays CAM1~CAM4 as quad split screen. The screen switches back when the hazard flasher trigger is switched off. CAM1 NOTICE CAM2 CAM1 CAM4 CAM2 CAM3 The example is set with TRG1(Reverse gear)=CAM1 / TRG2(Left turn signal)=CAM2 / TRG3(Right turn signal)=CAM3 5) When more than two trigger signals are received at once, the monitor will display the highest priority trigger.
７. SETTINGS 1 VIDEO STANDARD SYSTEM NTSC/PAL SELECTION PICTURE SETUP DIMMER CONTRAST BRIGHTNESS COLOR TINT LANGUAGE VIDEO SYSTEM RESET NOTICE AUTO 50 50 50 50 ENGLISH NTSC ▶ 1) Press [MENU] button until OSD menu [PICTURE SETUP] appears. 2) Press [ ] button to move a to VIDEO SYSTEM and choose video system by pressing [ ] button. Please select NTSC for video system as Clarion cameras are compatible with NTSC video system.
4 LANGUAGE SETTING PICTURE SETUP DIMMER CONTRAST BRIGHTNESS COLOR TINT LANGUAGE VIDEO SYSTEM RESET AUTO 50 50 50 50 ENGLISH NTSC ▶ 1) Press [MENU] button until OSD menu [PICTURE SETUP] appears. 2) Press [ ] button to move to language and choose proper value by pressing [ ] button. * Factory default setting is English (8 languages available).
８. INSTALLATION INSTALLATION (U-Bracket) Double side adhesive tape Standard Installation 1. Please ensure that the monitor is installed with enough room for heat to dissipate. Install the monitor stand with enclosed screws and double side adhesive tape as per the picture. 2. Fix the monitor to the monitor stand firmly. Double side adhesive tape Ceiling Installation Screw hole 3. Sun Visor should be installed with 4 screws.
9. CONNECTIONS MONITOR CABLE * Make sure that the connector cable with the correct pin configuration is used. *１ ORANGE GREEN BLACK (CAM1) (CAM2) (CAM3) CAM1 CAM2 CAM3 CAM4 *２ *１ *２ BLACK GROUND RED ACCESSORY(ACC) DC12V/24V *２ *１ *１ *２ Camera connecting cable *１ Use Clarion Cameras only. *２ A camera connecting cable, sold separately, is required for connecting the camera. ■ Please ensure that the correct trigger wires are connected to the corresponding cameras.
10. TROUBLESHOOTING Cause Problem Measure No image is displayed. Is camera connected properly? Check the wiring to the camera and the camera connection. Power does not turn on. Is power cable connected properly? Check the wiring. Is a fuse blown out? Replace with a fuse of the same amperage (5A) Operating environment is inappropriate. Temperature in the vehicle is below -10° C or over 60° C. Check to see that the temperature in the vehicle is appropriate (around 25° C). Color is washed-out.
MEMO 21
MEMO 22
MEMO 23
Clarion Co., Ltd. All Rights Reserved. Copyright © 2013: Clarion Co., Ltd.
