User's Manual
HOW TO INSTALL
How to attach the monitor with receiver
1.
place after removing protective tape from stand bottom.
2.
Fix the stand with enclosed screws.
3.
Assemble the monitor to the stand and adjust it to the correct viewing angle.
5
Self tapping screw
2
Adjustable bracket
4
Hexagon head bolts with built-in washer
How to mount the camera with transmitter
Never swin
g
the camera b
y
the cable or pull the cable. Doin
g
so ma
y
impair the
camera's waterti
g
htness or break the cable, resultin
g
in malfunction.
A
void mounting the camera where the lens will be exposed to dirt
(
mud splashes,
exhaust
f
umes, etc.
).
1.
To prevent camera shake, make mounting holes in a solid
location
below. If the part is not strong enough, carry out appropriate
reinforcement.
2.
After connecting the cables, adjust the mounting angle of the
camera so that the rear bumper or back end of the vehicle
appears in the monitor.
●
Be sure to use the supplied screws to mount the
camera.
●
If any screws are lost when mounting the camera, be
sure to use hexagon head bolts with built-in washer
(M3mm x 8mm). Do not under any circumstances use
screws that are longer than this. To ensure watertight-
ness, the screws in the camera case have a bag
structure. Use of long screws may damage the screw
thread and camera case, compromising watertightness.
WARNING
45 mm
0
Gasket
9
Antenna
Rotate the antenna and fix
securely to the receiver.
8
Mounting bracket
@
Hexagon head bolts
with built-in washer (M5 mm x 8 mm)
!
Hexagon head bolts
with built-in washer (M3 mm x 8 mm)
!
Hexagon head bolts with built-in washer (M3 mm x 8 mm)
#
Flanged nuts (M5 mm)
Vehicle side : 5.5 mm hole (Two places)
PAIRING
The pairing function has been set at factory level so pairing is not required at the initial installation
stage. The pairing steps can be skipped in this case.
If the camera or monitor are replaced for any reason, then pairing must be completed as per the
instructions below. Pairing is also required each time you change Tractor/Trailer combinations.
1.
Press the pairing button (on the rear of the monitor)
for four seconds.
2.
The words "please Press Pair Key on Camera Side"
will appear on the monitor. A 30 second timer will then
count down. Please pair before 30 seconds elapses.
3.
Pairing method
Pairing method depends on vehicle type and design
of vehicle wiring harness.
Installation Condition Pairing method
(1) - Trailer with tractor user
- Reverse gear signal is enabled at rear of
a vehicle
For tractor and trailer applications that can
get reverse gear signal at the rear of a
vehicle, it is recommended to connect the
camera pairing wire (Brown) to the +12V
parking light circuit.
To begin the pairing process, make sure
the parking lights are off and the vehicle is
in reverse gear. Turn the parking lights on
and begin the pairing process.
(2) - Users other than (1) For users under other conditions, connect
the pairing line to +12V/24V (ACC or
illumination active) line for one second.
When pairing is completed, disconnect and
insulate the end of this cable with insulating
tape.
4.
The camera video will appear on the monitor and pairing is complete.
WIRING AND CONNECTIONS
To prevent short-circuiting, check the connections again be
f
ore connecting the battery.
RedBrown Black
Camera with transmitter
Ground (Negative)
Connect to chassis ground.
Ground (Negative)
Connect to the metal part of the vehicle.
●
Do not connect the power
cable (red) of either the
transmitter or the receiver to
the +B line (permanent
power supply) as this may
lead to a flat battery.
●
Disconnect the negative
terminal of the battery before
connecting the cables.
Failure to do so may lead to
electric shock or injury due to
short-circuit. It may also lead
to damage to the system
components due to
short-circuit.
WARNING
RedBlack
Reverse or Parking light
Please refer to item 3. of PAIRING section.
ACC+
Connect to a positive power supply that can be turned on and
off with the ignition key.
Pairing
Please refer to the item 3. of PAIRING section.
Monitor with receiver
MONITOR SETUP
MENU
Input mode setting INPUT Must be CCD
INFORMATION View the current parameters
Color adjustment Adjust the display parameters
Audio adjustments Not applicable to this system.
System Information SLEEP TIMER Set to 0
WIDE SCREEN Set to WIDE
LANGUAGE Adjusting language
RESET Restore the initial settings
TROUBLE SHOOTING
The following situations may not be malfunctions. Check once more before requesting repairs.
Symptom Cause Remedy
There is no image (Nothing
appears on the monitor)
The receiver is not connected
correctly
Check the receiver’s connections and connect the re-
ceiver correctly
There is no image (“No Sig-
nal” is continuously displayed
on the monitor)
The camera is not connected
correctly
Check the camera’s connections and connect the cam-
era correctly
The surrounding radio wave
signal strength is weak
Move to a different place and check if the image ap-
pears
The image cuts out The surrounding radio wave
signal strength is weak
Move to a different place and check if the image ap-
pears
OTHER
IC Number :419C-EE2179
FCC CAUTION:
Changes or modifications not express.
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
This device complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of this device.
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF)
Exposure Guidelines and RFF-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the
radiator at least 20cm or more away from person's body (excluding extremities: hands, wrists, feet and ankles).
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum(or lesser) gain approved for
the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that
the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This radio transmitter IC Number (IC Number: 419C-EE2179, 419C-CC3500) has been approved by Industry Canada to operate with the antenna
types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not
included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Antenna type:Dipole Gain:2dBi Model:EE2179
Antenna type:Dipole Gain:2dBi (5dBi + Cable Loss 3dB) Model:EE2179
Antenna type:Dipole Gain:1dBi (7dBi + Cable Loss 6dB) Model:EE2179
This equipment has been tested and found to comply with the limits, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio reception, which can be determined by turning the equipment off and on, the user is
encouraged to consult the dealer or an experienced radio technician for help.
INFORMATION FOR USERS:
CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTURER WILL VOID THE WARRANTY AND
WILLVIOLATE FCC
Rear bumper or rear end
of the vehicle
About 7mm
Monitor screen
Pairing Button
+12V/24
V
419C-AVWCL1200
419C-AVWCL1200
419C-AVWCL1200
Gain:4dBi
Model:EE-2179
Model:EE-2179
Model:EE-2179
We Clarion declares that the
p
roduct EE-2179 is followin
g
the
p
rovision of Directive 1999/5/EC with the