HDBaseT Extender Set 70m User Guide Model CM-BT10-TXRX70 Doc ID 2015-04-350 • Rev 04
Copyright © 24APR15 Clare Controls, Inc. All rights reserved. This document may not be copied in whole or in part or otherwise reproduced without prior written consent from Clare Controls, Inc., except where specifically permitted under US and international copyright law. Trademarks and patents HDBaseT Extender Set 70m, Model CM-BT10-TXRX70 name is a trademark of Clare Controls, Inc.
Content Limitation of liability...ii Introduction...1 Features...1 Package contents...1 Product appearance...2 System connection...4 Usage precautions...4 Application examples...4 Connection procedure...6 Application...6 Twisted pair cable connection...7 Specifications...8 Panel drawings...9 Troubleshooting and maintenance...10 Safety operation...11 After-sales service...
Limitation of liability To the maximum extent permitted by applicable law, in no event will Clare Controls, Inc. be liable for any lost profits or business opportunities, loss of use, business interruption, loss of data, or any other indirect, special, incidental, or consequential damages under any theory of liability, whether based in contract, tort, negligence, product liability, or otherwise.
Introduction The extender set consists of a transmitter and receiver pair. HDMI signals are input into the transmitter and HDBaseT technology is used to transmit the signals to the receiver up to 230 ft. (70 m) via a Cat5e/Cat6 cable. The receiver then outputs the HDMI signal. Bi-directional IR and RS232 are also transmitted across the Cat5e/Cat6 cable. The extender set supports CEC, bi-directional RS232 and IR control, and PoC, which can be used to power the receiver via the Cat5e/Cat6 cable.
Product appearance Figure 1: The CM-BT10-TX70 transmitter (1) IR IR receiver. (2) ON Working status indicator of this device. When the CM-BT10-TX70 is on and working properly, the green LED blinks. (3) LINK HDBaseT link status indicator, green LED. It remains illuminated when the device has a connection. (4) IN The LED remains on when connected with devices that support HDCP and are working normally. If the devices do not support HDCP, this green LED blinks.
Figure 2: The HDBaseT Extender Set receiver (1) IR IR receiver. (2) ON Working status indicator of this device. When the CM-BT10-RX70 is on and working properly, the green LED blinks. (3) LINK HDBaseT link status indicator, green LED. Remains illuminated when there is a connection. (4) OUT The LED remains illuminated when connected with devices that support HDCP, and the HDCP handshake is working normally. If the devices do not support HDCP, this green LED blinks.
System connection Usage precautions • System should be installed in a clean environment and have proper temperature and humidity controls. • All of the power switches, plugs, sockets, and power cords should be insulated for safety. • All devices should be connected before powering on. • The Cat5e/Cat6 terminations for HDBaseT devices should be a straight-thru TIA/EIA T568B standard.
Example 1: CM-BT10-TXRX70 - HDBaseT Extender Set Example 2: CM-MT4410-BT-70 with CM-BT10-RX70 HDBaseT Extender Set 70m User Guide 5
Connection procedure To connect the HDBaseT Extender Set 70m 1. Connect HDMI from the source (such as Blu-ray DVD) to the HDMI IN port of the transmitter using an HDMI cable. 2. Connect the HDBT OUT port of the transmitter to the HDBT IN port of the receiver with a single CAT5e/CAT6 cable using TIA/EIA T568B terminations at each end. 3. Connect the HDMI OUT port of the receiver to an HDMI in port on the display using an HDMI cable. 4. When using the bi-directional IR control, do the following. a.
Twisted pair cable connection The Cat5e/Cat6 terminations for HDBaseT devices should be a straight thru TIA/EIA T568B standard. TIA/EIA T568A standard is NOT recommended.
Specifications Transmitter (CM-BT10-TX70) Receiver (CM-BT10-RX70) Input signal 1 HDMI,1 IR & 1 RS232 1 IR, 1 RJ-45 and 1 RS232 Input connector HDMI male, 3.5 mm mini jack, 3p captive screw connector 3.5 mm mini jack, RJ-45, 3p captive screw connector Video signal HDMI1.4 HDMI1.4 Audio Digital audio, transmit through HDMI audio Digital audio, transmit through HDMI audio Output 1 IR, 1 RJ45, and 1 RS232 1 HDMI, 1 IR, 1 RS232 Output connector 3.
Panel drawings HDBaseT Extender Set 70m User Guide 9
Troubleshooting and maintenance • No image on display: • Ensure that the display device has been set to the correct input. • Ensure that the HDMI cables used for both the source/transmitter and the receiver/display are properly connected and are working. Test the HDMI cables directly from a source to display and ensure their operation. • Ensure that the Cat5e/Cat6 cable has not been damaged and that it has been terminated correctly with T568B on both ends.
Safety operation To guarantee the reliable operation of the equipment and personal safety, please follow the procedures listed below. • The system must be grounded properly. Do not use two blades plugs. Ensure the supply voltage is in the correct range of 100~240 VAC, 50/60 Hz. • Do not locate the device in a place that is abnormally hot or cold or does not have proper temperature control and ventilation. • The CM-BT10-TX70 and CM-BT10-RX70 generate heat when operating.
After-sales service • If there appears to be problems when using the device(s), refer to the “Troubleshooting and maintenance” section in this manual. Return shipping costs are not covered by this warranty. • You can contact Customer Support at http://support.clarecontrols.com. Please be ready to provide the following information. • Product model number, version and serial number. • Detailed description of the trouble issues. • Description of all connections and 3rd party equipment being used.
