User Manual
Table Of Contents
- Technical Systems Electric System LEXION 570 – 520 Montana
- Layout of electric circuit diagrams
- Contents
- Central terminal compartment
- Pin assignment in modules
- Module A6 - Automatic air conditioner
- Module A7 - Cab fan speed controller
- Module A8 - AUTOCONTOUR (CAC)
- Module A9 – AUTOPILOT (ATP)
- Module A10 - Fieldwork computer (BIF/CAB)
- Module A12 - Speed monitor (DZW)
- Module A13 - Performance monitor (DKG)
- Module A15 - Electronic engine control module CATERPILLAR (CAT)
- Module A15 - Electronic engine control module DAIMLER-CHRYSLER (DC)
- Module A17 - Engine adaptation module ADM DAIMLER-CHRYSLER (DC)
- Module A16 – Reel controller
- Module A21 - Yield meter
- Module A25 - Sieve adjustment
- Module A27 - VARIO
- Module A28 - Uni-spreader (VGS)
- Module A30 - Terminal
- Module A33 - Sidefinder
- Module A34 - Grain tank
- Module A35 - Montana 570-520 control unit - with external MONTANA control unit (up to serial no. 582 00051, 581 00026; 580 00028)
- Module A36 - Montana 570-520 gearshift module - with external MONTANA control unit (up to serial no. 582 00051, 581 00026; 580 00028)
- Module A37 – Electro-hydraulic gearshift (EHS) - 3-speed manual gearbox
- Module A37 – Electro-hydraulic gearshift (EHS) - 2-speed manual gearbox
- Module A38 – Rotor (RIO)
- Module A42 – MONTANA GEN II module - with integrated MONTANA control unit from serial no. 582 00052, 581 00027 and 580 00029)
- Module A45 - Ground drive hydraulic motor brake restrictor (HBM)
- Module A46 – Deflector adjustment (RIO)
- Module A49 – Ground drive (EFA)
- Module A51 – Radial spreader
- Module A65 - GPS pilot terminal
- Module A66 - GPS pilot module (GPB)
- Circuit diagram 1a - 50a
- 01a - Main power supply, diesel engine electric starting motor
- 01s - Main power supply, diesel engine electric starting motor - Montana 570-520
- 02a - Starting the diesel engine, diesel engine electric starting motor - CAT C12, C10, C9, 3126B
- 02b - Starting the diesel engine, diesel engine electric starting motor- DC 502 LA
- 02s - Starting the diesel engine, diesel engine speed adjustment - CAT C12, C10, C9, 3126B, Montana 570-520 - with external MONTANA control unit (up to serial no. 582 00051, 581 00026; 580 00028)
- 02t - Starting the diesel engine, diesel engine speed adjustment
- 03a - Diesel engine cut-off system
- 04a - Road travel activation, master valve
- 04s - Road travel activation, working hydraulics master valve, Montana 570-520 - with external MONTANA control unit (up to serial no. 582 00051, 581 00026; 580 00028)
- 04t - Road travel activation, working hydraulics master valve, Montana 570-520 - with integrated MONTANA control unit (from serial no. 581 00027 to 581 00037)
- 05a - Terminal, keyboard, rotary switch, printer
- 06a - CAN bus, module power supply, for diesel engine CATERPILLAR - C12, C10, C9, 3126B
- 06b - CAN bus, module power supply, for diesel engine Daimler - Chrysler DC 502 LA
- 06s - CAN bus, module power supply, Montana 570-520 - with external MONTANA control unit (up to serial no. 582 00051, 581 00026; 580 00028)
- 06t - CAN bus, module power supply, Montana 570-520 - with integrated MONTANA control unit (from serial no. 581 00027 to 581 00037)
- 07a - Threshing mechanism circuit
- 08a - Concave adjustment / Threshing drum variable-speed drive
- 09a - Rotor flap adjustment / Rotor variable-speed drive
- 10a - Fan variable-speed drive
- 11a - Sieve adjustment
- 12a - Deflector adjustment
- 13a - Straw and chaff spreader, uni-spreader - LEXION 580
- 13b - Straw and chaff spreader, radial spreader
- 14a - Swinging the grain tank unloading tube
- 15a - Grain tank unloading / Grain tank unloading aid
- 16a - Rape cutting knife circuit
- 17a - Front attachment drive, reverser drive, front attachment quick stop
- 17s - Front attachment drive, reverser drive, front attachment quick stop, Montana 570-520 - with external MONTANA control unit (up to serial no. 582 00051, 581 00026; 580 00028)
- 18a - Front attachment variable-speed drive
- 19a - Straw chopper
- 19b - Straw chopper, radial spreader without chaff spreader
- 19c - Straw chopper, radial spreader with chaff spreader
- 20a - Front attachment raise/lower, cross levelling
- 20s - Raise/lower front attachment, cross levelling - Montana 570-520
- 21a - Reel adjustment - Standard cutterbar
- 21b - Reel adjustment - VARIO cutterbar
- 21c - Reel adjustment - Folding cutterbar
- 21d - Folding the maize picker, snapping plate adjustment, down maize augers
- 22a - Reel variable-speed drive
- 23a - Cutting table adjustment (Vario), folding the cutterbar
- 24a - AUTOCONTOUR (CAC)
- 25a - Speed monitor
- 26a - Machine monitor
- 26s - Machine monitor, Montana 570-520 - with external MONTANA control unit (up to serial no. 582 00051, 581 00026; 580 00028)
- 26t - Machine monitor, Montana 570-520 - with integrated MONTANA control unit (from serial no. 581 00027 to 581 00037)
- 27a - Yield meter / Grainmeter
- 28a - AUTOPILOT – Laser system
- 28b - AUTOPILOT – Feeler system
- 28c - AUTOPILOT – GPS-controlled steering
- 29a - Performance monitor
- 30a - Open / close grain tank (electric), grain tank full signal, warning beacon
- 30b - Open / close grain tank (hydraulic), grain tank full signal, warning beacon
- 31a - Front attachment dampening
- 32a - All-wheel drive, fuel tank
- 32b - All-wheel drive - overdrive, fuel tank
- 33a - Cutterbar spring lock
- 36a - Indicator system (Europe)
- 36b - Indicator system (USA)
- 37a - Windscreen wiper, windscreen washer
- 38a - Compressor-type air conditioner
- 38b - Automatic air conditioner
- 39a - Cab comfort equipment – operator's seat
- 40a - Additional sockets, fuse tester
- 41s - Axle control system, front attachment control system, Montana 570-520 - with integrated MONTANA control unit (up to serial no. 582 00051, 581 00026; 580 00028)
- 41t - Axle control system and front attachment contr
- 42a - Ground drive and brake control
- 42s - Ground drive and brake control, Montana 570-520 - with external MONTANA control unit (up to serial no. 582 00051, 581 00026; 580 00028)
- 42t - Ground drive and brake control, Montana 570-520 - with integrated MONTANA control unit (from serial no. 581 00027 to 581 00037)
- 44a - Electro-hydraulic gearshift - 3-speed manual gearbox
- 45a - Main lighting circuit, taillight, position light
- 46a - Dipped headlights, full beam, dipped headlights changeover switch
- 47a - Work lights I
- 48a - Work lights II
- 49a - Sieve, grain tank and returns lighting, reversing horn, brake light
- 50a - Instrument lighting, broadcast receiver, mirror adjustment
- Component grid
- Index
- 0293 676.0
TIC LEXION 500 Electric System
03/05 Lex-e-M M-23
Module A42 – MONTANA GEN II module - with integrated MONTANA control unit
(from serial no. 582 00052, 581 00027 and 580 00029)
Pin Function Compone
nt
Measuring
variable
Direction Circuit
diagram no.
X1/01 Earth --- Earth Input 06t,41t
X1/02 Electronic unit power supply F17 12V Input 06t,41t
X1/03 not used --- --- --- ---
X1/04 CLAAS CAN connection --- --- --- 06t
X1/05 CLAAS CAN connection --- --- --- 06t
X1/06 Inclinometer signal (CAN) B126 --- Input 06t,41t
X1/07 Inclinometer signal (CAN) B126 --- Input 06t,41t
X1/08 Diagnosis CAN connection XD2 --- --- 06t
X1/09 Diagnosis CAN connection XD2 --- --- 06t
X1/10 not used --- --- --- ---
X1/11 Earth sensors --- Earth Input 41t
X1/12 not used --- --- --- ---
X1/13 Earth sensors --- Earth Input 41t
X1/14 Earth --- Earth Input 04t,06t,41t
X1/15 Earth --- Earth Input 04t,06t,41t
X1/16 not used --- --- --- ---
X1/17 Right-hand axle angle sensor signal B92 0.25-4.75 V Input 41t
X1/18 Cutting angle sensor signal B93 0.25-4.75 V Input 41t
X1/19 Montana cross levelling sensor signal B94 0.25-4.75 V Input 41t
X1/20 MONTANA Automatic mode S85 12V PWM,
T signal (U
bat
/2)
Input 41t
X1/21 Axle position neutral position S86 12V PWM,
T signal (U
bat
/2)
Input 41t
X1/22 not used --- --- --- ---
X1/23 not used --- --- --- ---
X1/24 not used --- --- --- ---
X1/25 not used --- --- --- ---
X1/26 not used --- --- --- ---
X1/27 not used --- --- --- ---
X1/28 Earth --- Earth Input 04t,06t,41t
X1/29 Earth --- Earth Input 04t,06t,41t
X1/30 not used --- --- --- ---
X1/31 not used --- --- --- ---
X1/32 Left brake circuit pressure signal Z79 12V PWM,
T signal (U
bat
/2)
Input 26t
X1/33 Right brake circuit pressure signal Z80 12V PWM,
T signal (U
bat
/2)
Input 26t
X1/34 Parking brake signal S93 (Z12) 12V Input 41t
X1/35 MONTANA manual axle control
system
S79 12V PWM,
T signal (U
bat
/2)
Input 41t
X1/36 MONTANA manual front attachment
control
S80 12V PWM,
T signal (U
bat
/2)
Input 41t
X1/37 Lower machine/cutting angle S84 12V PWM,
T signal (U
bat
/2)
Input 41t
X1/38 Raise machine/cutting angle S83 12V PWM,
T signal (U
bat
/2)
Input 41t
X1/39 Rotate machine/front attachment to the
left
S81 12V PWM,
T signal (U
bat
/2)
Input 41t
X1/40 Rotate machine/front attachment to the
right
S82 12V PWM,
T signal (U
bat
/2)
Input 41t
X1/41 Left-hand axle angle sensor signal B91 0,25-4,75 V Input 41t
X1/42 Earth --- Earth Input 04t,06t,41t