User Manual

CLA-VAL
Copyright Cla-Val 2011 Printed in USA Specifications subject to change without notice.
P.O. Box 1325 • Newport Beach, CA 92659-0325 • Phone: [phone] • Fax: [phone] • E-mail: [e-mail] • Website cla-val.com
©
PV20
SERIES
Closed Body Pinch Valve
E-PV20 (R-3/2011)
OPERATION
The Cla-Val Series PV20 Closed Body Pinch Valves provide simple means to
manually control the flow of abrasive and corrosive slurries, liquids and solids.
The valve operates by turning the handwheel clockwise to close, counter-
clockwise to open like a gate valve, but unlike a gate valve the PV20 series
valve has no packing or metal surfaces to wear out - the sleeve is merely
squeezed to the desired open or closed position.The standard sleeve materi-
al, pure gum rubber, is made with reinforced polyester fabric for highest
strength and longer lasting cycle life. Sizes 8” and larger are available with
bevel gear operators for automatic operation.
MAINTENANCE
Cla-Val Pinch Valves are basically maintenance free because the sleeve iso-
lates all mechanical parts from the media. The sleeve is the only part typical-
ly inventoried for future replacement.
A
C
F
E
D
B
Series PV20 Closed Body Pinch Valves
1
1 1/2
2
2 1/2
3
4
5
6
8
10
12
14
16
18
20
24
Length
B
5 1/2
6 1/2
7
7 1/2
8
9
10
10 1/2
16
20
24
28
32
36
40
48
Working
Pressure psi.
150
150
150
150
150
150
125
125
75
75
75
50
50
50
50
50
Width
C
5 1/4
5 3/8
7 1/8
9 3/4
8 1/4
9 1/2
12 1/2
13
18 1/2
22 1/2
25
29
33
35
39
50 1/2
D
3
4
4 1/2
5
5
5 1/2
6 1/2
8
10
11
12
14
15
16
17
23
E
7 1/2
7 1/2
9 3/8
9 3/8
10 1/2
12
16
18
22
24
25
29
32
35
37
43
Diameter
F
4
4
8
8
8
12
11
18
22
22
22
30
30
36
36
48
Weight
(est.) lbs
12
25
34
43
52
123
200
300
345
410
472
588
930
1150
1300
1510
Heavy Construction at No Extra Cost!
• Rugged Ductile Iron body
• Easy to operate at high pressure
• Lubricated stem and bearing pad
• Stainless steel guide rods
• Reduced port sleeves for throttling flow
• Double wall sleeves for severe application
Quality Features at No Extra
Cost!
• Short face-to-face
• Full port area
• Center sleeve closure
• Tight shut-off on solids
• Over pinch guard
• Positive pull opening tabs
• Valve position clearly visible
Sizes 8” & larger available with bevel gear operators. Sizes up to 6” have
ANSI B16-10-51-FF lengths or special lengths available upon request.
Model
No
PV20.100
PV20.150
PV20.2
PV20.250
PV20.3
PV20.4
PV20.5
PV20.6
PV20.8
PV20.10
PV20.12
PV20.14
PV20.16
PV20.18
PV20.20
PV20.24
Many Synthetic Sleeve Materials Available:
Neoprene - Chlorobutyl - Hypalon - Buna-N
®
- Ethylene
Propylene Rubber - Urethane and Viton
TM
When ordering above sleeve materials add the first letter
of the material after the model number.
i.e. Model PV20.10N (N for Neoprene)
Pipe Size
A
WHEN ORDERING,
Please specify following information:
Flange
Drilling
ANSI
PN 6
PN 16
Other
ANSI 300
PN 10
BS 10
n
n
n
n
n
n
n
Sleeves Available
in Different Styles.
Pinch Valve
Standard Sleeve
Pinch Valve
Reduced Port Sleeve
Pinch Valve
Double Wall Sleeve