24-02/624-02
This page was intentionally left blank!
This page was intentionally left blank!
This page was intentionally left blank!
INSTALLATION / OPERATION / MAINTENANCE MODEL 100-01 Hytrol Valve Description The CIa-VaI Model 100-01 Hytrol Valve is a main valve for CIa-VaI Automatic Control Valves. It is a hydraulically operated, diaphragm-actuated, globe or angle pattern valve. This valve consists of three major components; body, diaphragm assembly, and cover. The diaphragm assembly is the only moving part. The diaphragm assembly uses a diaphragm of nylon fabric bonded with synthetic rubber.
Flow Direction Recommended Tools 1. Three pressure gauges with ranges suitable to the installation to be put at Hytrol inlet, outlet and cover connections. The flow through the 100-01 Hytrol Valve can be in one of two directions. When flow is “up-and-over the seat,” it is in “normal” flow and the valve will fail in the open position. When flow is “overthe seat-and down,” it is in “reverse” flow and the valve will fail in the closed position. There are no permanent flow arrow markings.
STEM TRAVEL (Fully Open to Fully Closed) Valve Size (inches) Travel (inches) Diaphragm Check (#1 ) 1. Shut off pressure to the Hytrol Valve by slowly closing upstream and downstream isolation valves. SEE CAUTION. 2. Disconnect or close all pilot control lines to the valve cover and leave only one fitting in highest point of cover open to atmosphere. 3.With the cover vented to atmosphere, slowly open upstream isolation valve to allow some pressure into the Hytrol Valve body.
Maintenance VALVE STEM THREAD SIZE Preventative Maintenance 1 1/4"—2 1/2" 3"—4" 6"—14" 16" 20 24" 30” 36” Valve Size The Cla-Val Co. Model 100-01 Hytrol Valve requires no lubrication or packing and a minimum of maintenance. However, a periodic inspection schedule should be established to determine how the operating conditions of the system are affecting the valve. The effect of these actions must be determined by inspection.
Lime Deposits Inspection of Parts One of the easiest ways to remove lime deposits from the valve stem or other metal parts is to dip them in a 5-percent muriatic acid solution just long enough for the deposit to dissolve. This will remove most of the common types of deposits. CAUTlON: USE EXTREME CARE WHEN HANDLING ACID. Rinse parts in water before handling. If the deposit is not removed by acid, then a fine grit (400) wet or dry sandpaper can be used with water.
6 17 1 25 5 2 24 7 8 9 10 INLET OUTLET 3 4 TOP VIEW 14 16 GLOBE PATTERN PARTS LIST Item 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31.
100-01 8" 10" 100 150 200 250 300 350 400 20", 24" 600 500 600 4" 6" 8" 10" 12" 14" 16" 20" 24" 30" 16" 12" 800 400 300 250 200 150 80 3" 6" 65 2 1/2" 100 40 50 4" mm 2" 32 1 1/4" inches 100-20 1 1/2" 25 1" inches mm 100-01 HYTROL SIZE 6.75 5.63 4.5 3.9 3.4 2.8 2.3 1.7 1.1 0.8 0.7 0.6 0.4 0.4 0.3 inches 165 143 114 99 86 71 58 43 23 20 18 15 10 10 8 3/8 - 24 24.60 108.80 45.
0 4 1 4 12 8 3 2 7 11 9 3 5 12 4 14 8 1 4 16 6 6 9 BOLTS 1 16 2 BOLTS 10 3 2 5 15 7 6 11 3 13 8 4 1 5 17 8 15 BOLTS 1 6 2 9 7 3 7 13 3 5 12 6 11 19 20 2 18 4 14 10 16 BOLTS 8 20 BOLT/NUT TORQUING PROCEDURES ON VALVE COVERS 4 5 BOLTS 1 12 2 BOLTS 6 Follow this procedure when reassembling MAIN Valve: 1.
INSTALLATION / OPERATION / MAINTENANCE MODEL 100-20 (Reduced Internal Port) 600 Series Hytrol Valve SERVICE AND MAINTENANCE OF 600 SERIES VALVES The 600 series main valves have only one part -the body- that is different from standard 100 Series Cla-Val main valve parts. The remaining parts of the 600 series main valve are standard ClaVal main valve parts. All service and maintenance information for the standard 100 Series main valves in this manual also apply to the 600 series main valves.
100-20 PARTS LIST NO.
INSTALLATION / OPERATION / MAINTENANCE CF1 Series CF1 Series Float Controls Initial Adjustment CF1 Series Float Controls Check installation to be sure that liquid surface is not subject to wind or currents, if so, a stilling well should be installed around the float and rod assembly. A short section of 8" pipe (PVC) mounted vertically in the tank around the float and rod is suggested. 1.
PARTS LIST CF1-C1 Float Control 11 17 16 1 15 14 12 19 PILOT & BRACKET ASSEMBLY 2 COUNTERWEIGHT NOT INCLUDED 4 4 18 13 5 5 7 6 8 3 FLOAT ROD ASSEMBLY 8 10 10 OPERATION 9 FLOAT POSITION Up Down PORT 1 Pressure Drain PORT 2 Drain Pressure 7 9 Optional Stainless Steel Float ITEM 1 2 3 4 5 6 7 8 9 10 10 SS 11 12 13 14 15 16 17 18 19 DESCRIPTION Link Assembly Cotter Pins (2 req'd) Float Rod Assembly (2 ft. ) FLOAT ROD ASSY. BREAKDOWN ITEMS 4 - 9 Upper Float Rod (1 ft.
PARTS LIST 100-01 MODEL 3/8"-1 Hytrol Valve PARTS LIST ITEM DESCRIPTION A 1. 2. 3. 4. * 5. * 6. 7. 8. A 2.50 Cover Screw (8 Required) Cover Spring Diaphragm Washer Diaphragm Disc Retainer Assembly Body Plug (3/8 NPT) Body * Recommended Spare Parts OPERATING PRESSURE 1/8 NPT 2 3 1 4 1.50 5 3/8 NPT BOTH ENDS INLET 1.25 6 8 3/8 NPT 2.
PARTS LIST MODEL 100-01 1/2"-3/4"-1” Hytrol Valve PARTS LIST 100-01 3/4" & 1/2" Hytrol Valve OPERATING PRESSURE 1/8 4 3 1 5 2 C OUTLET INLET 6 9 ITEM DESCRIPTION 1 2 3 4 5 *6 *7 8 9 10 11 12 13 COVER SCREW COVER SPRING STEM NUT DIAPHRAGM WASHER DIAPHRAGM DISC RETAINER ASSEMBLY DISC GUIDE & STEM BODY SEAT NAMEPLATE BODY PLUG HEX HD.
PARTS LIST CG Series Globe and Angle Valves CG Series 8 7 4 6 9 2 5 3 1 CAT. NO. CGA ANGLE CAT. NO. CG8 GLOBE PARTS LIST FOR ILLUSTRATION ONLY. VALVE SOLD ONLY AS A COMPLETE UNIT. When ordering parts, please specify: All Nameplate Data or Numbers Stamped on Assembly Item Description 1. 2. 3. 4. 5. 6. 7. 8. 9. Body Bonnet Disc Stem Gland Nut Handwheel Nut Packing Box 1325 • Newport Beach, CA 92659-0325 • Phone: 949-722-4800 • Fax: 949-548-5441 • E-mail: claval@cla-val.com • Website cla-val.
This page was intentionally left blank!
INSTALLATION / OPERATION / MAINTENANCE MODEL X46 Flow Clean Strainer • Self Scrubbing Cleaning Action • Straight Type or Angle Type The Cla-Val Model X46 Strainer is designed to prevent passage of foreign particles larger than .015". It is especially effective against such contaminant as algae, mud, scale, wood pulp, moss, and root fibers. There is a model for every Cla-Val. valve.
This page was intentionally left blank!
Box 1325 • Newport Beach, CA 92659-0325 • Phone: 949-722-4800 • Fax: 949-548-5441 • E-mail: claval@cla-val.com • Website cla-val.com Copyright Cla-Val 2009 Printed in USA Specifications subject to change without notice. CLA-VAL P.O.
This page was intentionally left blank!
Cla-Val Product Identification How to Order Proper Identification For ordering repair kits, replacement parts, or for inquiries concerning valve operation, it is important to properly identify Cla-Val products already in service by including all nameplate data with your inquiry. Pertinent product data includes valve function, size, material, pressure rating, end details, type of pilot controls used and control adjustment ranges. INLET EINTRITT ENTREE ENTRADA SIZE & CAT NO. STOCK NO. CODE MFD.
SPECIFY WHEN ORDERING HOW TO ORDER • Model Number • Globe or Angle Pattern • Adjustment Range (As Applicable) Because of the vast number of possible configurations and combinations available, many valves and controls are not shown in published product and price lists.
INSTALLATION / OPERATION / MAINTENANCE MODEL REPAIR KITS Complete Replacement Diaphragm Assemblies for 100-01 and 100-20 Hytrol Main Valves For: Hytrol Main Valves with Ductile Iron, Bronze Trim Materials—125/150 Pressure Class Only. FACTORY ASSEMBLED Includes: Stem, Disc Guide, Disc, Disc Retainer, Spacer Washers, Diaphragm, Diaphragm Washer and Stem Nut.
Repair Kits for 100-02/100-21 Powertrol and 100-03/100-22 Powercheck Main Valves For: Powertrol and Powercheck Main Valves—125/150 Pressure Class Only Includes: Diaphragm, Disc (or Disc Assembly) and O-rings and full set of spare Spacer Washers.