32’’ MULTI-TOUCH-MONITOR MTIR-FR02-V1 Operating Manual
BETRIEBSANLEITUNG Document Rev. Rev. 001 Description First issue Author TTHA Date 2011-02-17 Disclaimer The contents of this manual are for information purposes only. Citron GmbH reserves the right to change the contents of this manual without prior notice. While reasonable efforts have been made in the preparation of this manual to assure its accuracy, errors may occur.
MULTI-TOUCH-MONITOR MTIR-FR02-V1 Contents Introduction ..................................................................................................................................................................... 4 1 Precautions.............................................................................................................................................................. 5 1.1. General Safety ..............................................................................................
BETRIEBSANLEITUNG Introduction The MTIR-FR02-V1 Multi-Touch-Monitor is comprised of a 32 inch Multi-Touch frame made by Citron GmbH, Germany mounted on an LCD-monitor PD-CP32AH made by Canvys, Germany. This operating manual describes the set-up of the Multi-Touch-Frame. For all other aspects reference the original manual of PD-CP32AH LCD screen WARRANTY AND ALL WARRANTY CLAIMS ARE VOID IF INSTRUCTIONS IN THIS MANUAL ARE NOT OBEYED.
MULTI-TOUCH-MONITOR MTIR-FR02-V1 · 1 Precautions Please carefully read these instructions before you start. Failure to follow these instructions may result in damage or personal injury · 1.1. General Safety The unit must be set-up by authorized and qualified personnel only. · Always obey relevant local safety regulations. · Setting up should be performed by two persons. · MTIR-FR02-V1 Multi-Touch-Monitor should only be used with the specified input voltage conditions (see section 7.
BETRIEBSANLEITUNG 2 Package Contents The cardboard box containing your new Multi-Touch-Monitor contains the following parts: Contents Multi-Touch-Monitor MITR-FR02-V1 Front bezel Accessories kit: DVI Cable Power lead USB Cable A/B Magnetic Tape 85 cm Magnetic Tape 54 cm 6 Qty 1 1 1 1 1 2 2
MULTI-TOUCH-MONITOR MTIR-FR02-V1 3 Installation The following guidance must be observed when mounting the device. Failure to do so may result in breakage or damage to the unit. No warranty claims are accepted for damages caused by not following these instructions · When mounting the multi-touch-monitor care should be taken not to obstruct the cooling air ventilation of the monitor. Ventilation openings must be kept clear.
BETRIEBSANLEITUNG 3.2 Setting Up Main Power Switch Power Key M U EN CT LE SE W PO ER Operating-LED 1. Switch the main power switch “ON” 2. Start your computer 3 The Multi-Touch-Monitor is switched ON/OFF using the power key. Regular operation is indicated by a steady green light. If there is no video input or the monitor is on stand-by mode the LED emits red light. 3.
MULTI-TOUCH-MONITOR MTIR-FR02-V1 4 Operating the OSD 4.1 OSD-Operating-Keys (On-Screen-Display-Menue) OSD-Menu Keys are located on the back of the Multi-Touch-Monitor.
BETRIEBSANLEITUNG 4.2.2 Image Adjustments Within the main-menu item “Image Adjustments“ you can control image settings like brightness, contrast, etc. Brightness Contrast Backlight Backlight mode Use ▲▼-keys to adjust brightness Use ▲▼-keys to adjust contrast Use ▲▼-keys to adjust backlight brightness Valid only with ambient light sensor 4.2.3 Color Adjustments Within the main-menu item “Colour Adjustments“ you can control colour settings like colour temperature etc Autom.
MULTI-TOUCH-MONITOR MTIR-FR02-V1 5 Cleaning CAUTION: 5.1 Disconnect the Multi-Touch-Monitor from power supply before cleaning. Wait until all parts are completely dried before re-connecting power. Cleaning of Monitor Parts Clean the monitor surface using a dampened cloth. Take care that no liquid enters the device. Clean the device surfaces with a smooth, non scratching lint-free cloth. Do not use any cleaning agents or paper towels. 5.
BETRIEBSANLEITUNG 6 Trouble-shooting Error Operating LED is off Reason - Main power switch is off - No image No power supply Corrective - Switch on main switch - Check power chord - Check wall plug - cabling is missing or faulty - Check DVI or VGA cable Check power chord - Main power switch is off - Switch on main switch - Monitor in stand-by mode - Switch on using „power“-key - Wrong input channel selected - Use OSD to select other input channel - Image is not visible - Use OSD
MULTI-TOUCH-MONITOR MTIR-FR02-V1 Touch is not working - Some cabling is missing or loose. Monitor has switched off automatically - Touch operation unstable - Driver is not installed correctly - - Poor USB cable quality - - USB cable too long - video cards is supported by monitor. Check USB connection at the monitor.
BETRIEBSANLEITUNG 7 Technical Data 7.1 Electrical Power Supply: Current Consumption: Monitor Interface: Touch Interface: 7.2 LCD Screen Panel Type: Display Size: Resolution: Colours: 7.3 Communication Protocol: Max.
MULTI-TOUCH-MONITOR MTIR-FR02-V1 8 Product Label 9 Ordering Information Order Number MTIR-FR02-V1-A01 Description 32” dreaMTouch including LCD-monitor 15
MULTI-TOUCH-MONITOR MTIRFR02-V1 BETRIEBSANLEITUNG Citron GmbH Anwaltinger Str. 14 D - 86165 Augsburg Telefon +49 (0)821 / 7 49 45 - 0 Fax +49 (0)821 / 7 49 45 – 99 16 info@citron.de // www. citron.
