English TM INSTRUCTION MANUAL FOR DIGITAL BLOOD PRESSURE MONITOR REF CH-602B IDENTIFICATION OF PARTS Battery cover Systolic blood pressure display section Diastolic blood pressure / Pulse display section Start switch Power switch Wrist cuff - Eng 1 -
SPECIFICATIONS Measuring method: Indication: Measuring range: Accuracy: Inflation: Deflation: Exhaust: Memory function: Power source: Battery life: Rated voltage: Working temp. & humidity: Storage temp. & humidity: Left wrist circumference: Outside dimensions: Weight: Electric shock protection: Accessories: Oscillometric system Digital display Pressure; 0 ⬃ 280mmHg, Pulse; 40 ⬃ 200 beat/min.
General Remarks on blood pressure measurement For proper measurement of blood pressure • If the cuff is to be deflated quickly, depress “POWER” switch. • The attached cuff is suited for a wrist circumstance of 13.5cm to 19.5cm. • When attaching the cuff, the body of a blood pressure monitor should be placed on the inside of your wrist. • Self measurement is no therapy! In no case may you change the dosage of medication prescribed by your physician.
PRECAUTION FOR USE AND MAINTENANCE Precautions for use Nature and frequency of maintenance: • If you suffer from heart disease, high blood pressure or other circulatory disease, please consult your doctor first. • If you feel abnormal pressure of the cuff during use or any other irregularity, reduce the pressure by immediately switching off the power or removing the batteries and consult the sales outlet where purchased.
• To use this unit, you must install batteries, and also if battery mark ” will appear on the display, you must change two pieces of “ batteries. • After fastening the under hook, close the battery cover. • “LR03” batteries or equivalent is suitable for this blood pressure monitor. • Open battery cover as illustrated. Replace the new two pieces of batteries, matching the (+) and (–) polarities on each battery with the polarity marks on the case.
MEASUREMENTS 1. Turn Power On SYSTOLICmmHg DIASTOLICmmHg mmHg DIASTOLIC mmHg PULS/min POWER STA RT SYSTOLIC PULSE/min After all display marks are disappeared, the last measured systolic and diastolic blood pressure values are displayed. (Value of the pulse is not memorized nor displayed.) Memory function works on for approximately one second or during “POWER” switch is depressed. Press the “POWER” switch to turn on.
English SYSTOLICmmHg DIASTOLICmmHg PULSE/min Wrist edge After three short buzzer beeps, the “0” appears on the display. Then, ready for measurement. Place the wrist cuff at the 1cm from the wrist edge. 2. Attaching of Wrist Cuff Wrist cuff Wrap the cuff around your wrist securely. Open the wrist cuff as the figure. Wrap the cuff around your wrist securely so that there is no space between the wrist and cuff with the edge of wrist cuff pulled.
SYSTOLICmmHg SYSTOLICmmHg DIASTOLICmmHg DIASTOLICmmHg PULSE/min PULSE/min Place your elbow on a table so that the palm is turned upwards and the cuff center is as high as your heart. Relax your entire body. SYSTOLICmmHg DIASTOLICmmHg 3. To Start the Measurement When inflation is completed, the automatically exhaust mechanism will gradually deflate the pressure in the “wrist cuff”, and the mark “Q” will appear indicating that measurement is in progress.
Press the “Power Switch” to turn OFF. DIASTOLICmmHg 6. Automatic Power Off Function If this unit is left on after measurement, an Automatic PowerOFF Function turns the power OFF after approximately 3 minutes. To continue measurement press the power switch to turn the unit ON. PULSE/min When diastolic pressure value is detected, the measurement is complete. Systolic pressure value is displayed on the upper side and diastolic pressure on the lower side of the display.
DESCRIPTION OF DISPLAY MARKS DISPLAY MARK CONDITION/CAUSE CORRECTIVE ACTION Measurement is begun, but the pressure was insufficient. Repeat measurement again. Appears when the blood pressure could not be measured accurately. (Some noises were detected by the movement of arm during measurement). Repeat measurement again. First, exhaust air from the cuff, reapply the cuff properly and remeasure. Repeat measurement again. Appears when the pulse could not be measured.
●CITIZEN is a registered trademark of Citizen Watch Co., Japan. Consumer Electronics Division CBM Bldg. 5F, 5-68-10, Nakano, Nakano-ku, Tokyo 164-0001, Japan Phone: (03)5345-7430 Fax: (03)5345-7431 E-mail: info-con@jcbm.co.
