English TM INSTRUCTION MANUAL FOR DIGITAL BLOOD PRESSURE MONITOR REF CH-611C IDENTIFICATION OF PARTS Air hose Hose plug Systolic blood pressure display section Diastolic blood pressure/ Pulse display section Hose socket Power switch CH-611C SYSTO LIC mmHg Start switch SELECT DIASTOLIC mmHg Memory recall switch MEMORY PULSE / min START Wrist cuff POWER Pressure setting switch - Eng 1 - Memory reset switch Battery cover
SPECIFICATIONS Measuring method: Indication: Measuring range: Accuracy: Inflation: Pressurization setting: Deflation: Exhaust: Memory function: Power source: Battery life: Rated voltage: Working temp. & humidity: Storage temp. & humidity: Outside dimensions: Weight: Electric shock protection: Accessories: Oscillometric system Digital display, Height: 19mm Pressure; 0 ⬃ 280mmHg, Pulse; 40 ⬃ 200 beat/min.
After cleaning the cuff with a neutral detergent, lightly rinse it with water and let it dry in the air. Hard rubbing or washing in a washing machine will cause air leakage. Also, be careful not to get water into the air hose. GENERAL REMARKS General Remarks on blood pressure measurement For proper measurement of blood pressure • If the cuff is to be deflated quickly, depress “POWER” switch. • The attached cuff is suited for a wrist circumstance of 13.5cm to 19.5cm.
• Do NOT keep on measuring so many times, as your arm will have built up congestion of blood, and you will not get a valid reading. • Do NOT measure blood pressure immediately after drinking coffee or tea or smoking. • Measure blood pressure with a relaxed and quiet posture. Keep the center of the cuff at the level of your heart, and do NOT move your arm or talk during measurement.
Manufacturer: Please help protect natural environment by respecting national and/or local recycling regulations when disposing of the batteries and the products at the end of their useful lives.
2. Attaching of wrist cuff All display marks appear for approx. 1 second and buzzer beeps. After all display marks are disappeared, deflation mark “▼” appears for approx. 1 second (three short beeps notify you of ready for measurement) then the last pressure setting value appears for approx. 3 seconds. Then the “ 0 ” appears at the display. • Open the wrist cuff as the figure.
English 1cm • Place the wrist cuff at the 1cm from the wrist edge. At this time, the air hose should be laid across the palm of the hand extending toward the middle finger. • Place your elbow on table so that the cuff is at the level as your heart. Relax your entire body, especially from elbow to your finger. 3.
When the diastolic pressure value is detected, the measurement is completed and buzzer sounds. 4. To start the measurement CH-611C SYSTILIC mmHg SELECT DIASTILIC mmHg Press the “Start Switch”. Systolic pressure is displayed on the upper and diastolic pressure on the lower side of the display. MEMORY PULSE / min START POWER The wrist cuff pressurizes when the “Start Switch” is pressed. 2 to 3 seconds after completion of measurements, the mark “▼” appears and air will deflate immediately.
CH-611C SYSTILIC mmHg SELECT DIASTILIC mmHg MEMORY PULSE / min START POWER When the pressure setting is needed to be changed, press the “Pressure Setting Switch” and select optimum value. Flushing Flushing 8. Memory recall This blood pressure monitor has a function which is able to display last measured value.
— New blood pressure value is stored in memory at pressing “Power Switch” for turn OFF or at pressing “Start Switch” for new measurement. 9. Automatic power off function If this unit is left on after measurement, an Automatic Power-OFF Function turns the power OFF after approximately 3 minutes. To continue measurement press the power switch to turn the unit ON. 10.
DISPLAY MARK CONDITION/CAUSE CORRECTIVE ACTION Measurement is begun, but the pressure was insufficient. Appears when the blood pressure could not be measured accurately. (Somenoise was detected or moved arm during measuring.) Appears when the pulse could not accurately be measured. Change the pressurization setting one level by pressing “Pressure Setting Switch” and measure once again. (Automatic remeasuring will be done only 1 time.) Repeat measurement again.
●CITIZEN is a registered trademark of Citizen Watch Co., Japan. Consumer Electronics Division CBM Bldg. 5F, 5-68-10, Nakano, Nakano-ku, Tokyo 164-0001, Japan Phone: (03)5345-7430 Fax: (03)5345-7431 E-mail: info-con@jcbm.co.
