Setting Guide
NOTE: Under normal conditions, this watch will
receive radio signals to automatically update the time
and calendar. There may be conditions in which the
radio signal cannot be received. If a signal cannot
be received, the watch will operate normally, but not
update.
NOTE: After a complete loss of charge or an abnormal
display or function is noticed, an ALL RESET
PROCEDURE and 0-POSITIONING CHECK AND
CORRECTION is required. Be sure to set the time and
date after performing these procedures.
NOTE: This watch features an EL backlight
which will illuminate the digital displays. This is
activated by pressing the upper right button (B)
Radio Reception
The watch will receive radio signals both automatically
and on-demand. Both the time and calendar will update
based on the current time zone.
then if needed, at 3:00 a.m. then 4:00 am. If the
updating will not be activated. The 4:00 a.m. automatic
update time may be user set to an alternate time if so desired.
The “on-demand” reception feature allows the user to
enter the reception mode at their convenience. This is
helpful when changing time zones before the automatic
update or if an automatic update was not successful.
NOTE: Depending on signal strength, it can take up to
15 minutes to complete the update. During the update
process, the watch must not be moved otherwise the
transmission signal may be interrupted resulting in an
unsuccessful time/calendar update.
For in-depth instructions on the radio reception feature,
please refer to your owners guide.
ALL RESET PROCEDURE
Pull the crown out one ‘click’ and rotate
so that the mode hand points to ‘CHR’.
Pull the crown out another ‘click’ to the setting
position.
Press the upper right (B) and lower right (A)
buttons down simultaneously for 3-seconds, then
release them. All digital segments in the displays
will be highlighted and the hands will move back
and forth to indicate the ALL RESET is successful.
Press the crown in to the closed position. You must
now continue with the 0-POSITIONING CHECK AND
CORRECTION PROCEDURE.
0-POSITIONING CHECK AND CORRECTION
Pull the crown out one ‘click’ and rotate so that the
mode hand points to ‘CHR’.
Pull the crown out another ‘click’ to the setting
position. Each hand will move to the 0-position set in
correct 0-position for the charge level/frequency hand
is the center of the ‘H’ in ‘CHN’, while all other hands
all hands point to their respective 0-position, press the
crown in two ‘clicks’ to the closed position. If any of the
hands do not indicate their correct 0-position, you will
need to continue this procedure.
Press and hold the upper right button (B)
for two or more seconds, then release. This
Turn the crown clockwise or counterclockwise until
the charge/frequency hand points to the center of
‘CHN’ on the frequency scale.
Press and release the upper right button (B). The
clockwise or counterclockwise until both the UTC hour
Press and release the upper right button (B).
clockwise or counterclockwise until the hour hand
Press and release the upper right button (B).
clockwise or counterclockwise until the minute hand
Press and hold the upper right button (B) for two or
more seconds, then release and push the crown to the
closed position next to the case. The analog hands will
move to the time set in memory and ‘CHR’ will show in
‘on-demand’ reception or manually.
ON-DEMAND RADIO RECEPTION
NOTE: On demand radio reception is used after an all
reset and may be used when traveling or after daylight
savings time.
Pull the crown out one ‘click’. Turn the crown
clockwise or counterclockwise to turn the mode hand
Press and release the lower right button (A) or upper
right button (B) until a city in your time zone is shown.
Simultaneously press and release the lower right
button (A) and upper right button (B). This will update
digital display 1 and the analog hands to your current
time zone.
Push the crown in one ‘click’. Press and hold the
lower right button (A) for two or more seconds until you
hear a beep. The second hand will move to the ‘RX’
move to the current signal available, digital display 1
Place the watch in a stable position so that it is not
moved. It can take up to 15 minutes to complete the
update process.
Upon detection of a radio signal, the second hand will
move to indicate the signal strength.
If a signal is detected and updating is successful digital
display 1 will show ‘OK’ and the second hand will resume
normal function.
If no signal is detected, digital display 1 will show ‘NO’
and the second hand will resume normal function. If no
signal can be detected, you will need to proceed with
manually setting the time.
TO MANUALLY SET THE TIME
NOTE: After receiving a radio signal, the time will
automatically set. There may be circumstances however
for which you need to manually set the time such as
after an all reset or you are in an area that inhibits signal
reception.
Pull the crown out one ‘click’. Rotate the crown
clockwise or counterclockwise until the mode hand points
Press and release either the upper right button (B)
or lower right button (A) until a city in your time zone is
shown in digital display 1.
Pull the crown out an additional ‘click’ to activate the
time setting mode. The second/transmission strength
Press and release the lower right button (A) to activate
Press and release the upper right button (B). The
the lower right button (A) to set the seconds to 0.
Press and release the upper right button (B). The
clockwise or counterclockwise to set the current minute.
Press and release the upper right button (B). The hours
counterclockwise to set the current hour.
Push the crown in one ‘click’. Simultaneously press and
release the lower right button (A) and upper right button
the time zone shown in digital display 1 and the analog
hands will move to the time in that time zone.
Push the crown in one ‘click’ to the closed position
next to the case. This completes setting the time.
For instructions on setting the calendar and details of
the many additional features of the of your timepiece,
please refer to the full instruction manual or the technical
support section of our website at www.citizenwatch.com
UTC Hour Hand
Reception Standby
Scale
Reception Fail Scale
Charge Level Scale
Frequency Scale
Charge Level/
Frequency Hand
Seconds/Reception
Strength/Transmission
Indicator hand
Digital Display 1
Lower Right Button (A)
Upper Right Button (B)
Crown