DOT MATRIX PRINTER MODEL iDP3110
iDP3110 User's Manual Declaration of Conformity Manufacturer’s Name : Manufacturer’s Address Declare the Product Product Name Model Number(s) Conform to the following Standards LVD EMC : Japan CBM Corporation : CBM Bldg., 5-68-10, Nakano, Nakano-ku, Tokyo, 164-0001, Japan Dot Matrix Printer iDP3110 Series (iDP3110R, iDP3110P) (S.No.
iDP3110 User's Manual IMPORTANT SAFETY INSTRUCTIONS * Read all of these instructions and save them for later reference. * Follow all warnings and instructions marked on the product. * Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. * Do not use this product near water. * Do not place this product on an unstable cart, stand of table. The product may fall, causing serious damage to the product.
iDP3110 User's Manual IMPORTANT: This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.
iDP3110 User's Manual CONTENTS 1. INTRODUCTION ......................................................................................................................................... 1 1.1 Features ................................................................................................................................................................ 1 1.2 Accessories.....................................................................................................................................
iDP3110 User's Manual 1. INTRODUCTION The iDP3110 is a dot-impact printer suitable for use with various data communication terminals, and measurement terminals. This product is extremely compact and features extensive functions suited for a wide range of applications. Please read this manual thoroughly to understand the printer before use. 1.1 Features 1. 2. 3. 4. Compact desk-top dot matrix printer Light weight High speed printing Low power consumption 1.
iDP3110 User's Manual 2. TYPE CLASSIFICATIONS 2.1 Type The product is categorized according to the naming plan indicated below. iDP3110 iDP3110 24 P J 120 A 40 R F 230 B 24 P J 120 A Model Name Printer cover A : 60mm(Dia.) Paper roll B : 80mm(Dia.) Paper roll Number of columns 24 : 24 columns/144 dots 40 : 40 columns/180 dots Power source 120 : AC 120V 230 : AC 220-240V Interface P : Parallel (Centronics) R : Serial (RS-232C) Character J : Japanese F : International 2.
iDP3110 User's Manual 2.3 Specifications Item 1 Printing method 2 Printing direction 3 Character configuration iDP3110-24* Dot matrix One-way printing (5 + 1) × 8 (W × H) 4 Number of columns per line 5 Printing speed 6 Character size (W × H) 7 Line pitch 8 Paper 9 Interface 10 Ribbon cassette 11 Voltage 12 Power consumption 13 Weight 14 Dimension 15 Operating temp. 16 Storage temp CITIZEN iDP3110-40* (4 + 0.5) × 8 24 columns: 144 dot/line 40 columns: 180 dot/line Approx. 2.5 line/sec. Approx. 1.
iDP3110 User's Manual 3. EXTERNAL APPEARANCE AND PART DESCRIPTION 3.
iDP3110 User's Manual 3.2 Part Descriptions 1. DC Jack Insert the output plug of the AC adapter attached. 2. Power Switch When switched ON, power is supplied to the printer, starting the initializing operation. 3. Power Lamp Lighted when power is turned ON and goes out when turned OFF. 4. SEL Lamp Lighted when printer is in the selected condition (ON-LINE). Printer becomes operational only when this lamp is on. 5. LF Switch Paper is fed when switch is pressed (de-select condition only).
iDP3110 User's Manual 4. OPERATIONS 4.1 Connection of the AC Adapter (1) Ensure that the power switch is OFF. (2) Insert the output plug of the AC adapter into the DC jack of the printer. (3) Insert the power plug of the AC adapter into a power concent supplying the designated voltage. (Use of exclusive AC adapter is recommended. Output is DC 7V, 1.2A. Avoid using power sources not conforming to this specification.
iDP3110 User's Manual 4.2 Setting of the Printer Cover (1) Hold the protruding section at the rear of the printer cover and lift in the direction indicated. (2) Attach the cover by pressing downward after hooking the cover to the acceptor located in the front part.
iDP3110 User's Manual 4.3 Setting of Ribbon Cassettes (1) Remove the printer cover after turning OFF the printer. (2) Press down on the Ribbon cassette while inserting the ribbon between the printing head and the platen. (3) Wind up the ribbon slack by turning the knob in the direction of the arrow.
iDP3110 User's Manual 4.4 Setting Paper (1) (2) (3) (4) (5) Remove the printer cover. Ensure that the end of the paper is straight or incline as indicated in the diagram. Insert the end of the paper into the slot of the printer mechanism. After turning ON the printer, press the LF switch until 5 to 6 cm of paper is fed out of the printer mechanism. Insert paper after moving aside the paper holder in the direction of the arrow. Then, secure the center of the roll with the holder.
iDP3110 User's Manual 4.5 Self Test Printing A self-printing function is incorporated in this product to enable the printer to check itself. This function is triggered by the following procedure. (1) Set paper to the printer. (2) Ensure that the ribbon cassette is attached correctly and turn the power OFF. (3) Turn ON the power switch while holding the LF switch down. Release the LF switch after the self-printing operation has started. Printing is initiated by this operation.
iDP3110 User's Manual 5. PARALLEL INTERFACE 5.1 Specifications a) Data input system b) Control signal c) Compatible Connector : 8 bit parallel (DATA 1-8) : ACK, BUSY, STB, RESET, SELECT : Printer side : 57LE-40360 (AMPHENOL or equivalent) : Cable side : 57-30360 (AMPHENOL or equivalent) 5.
iDP3110 User's Manual 5.3 Description of Input / Output Signals (1) Input signal All input signals utilize type 74HC of CMOS and can be used in TTL level as the input is pulled up with 3.3 kΩ resistance. - DATA 8 bit parallel signal (positive logic) - STB Strobe signal for reading out data (negative logic) - RESET Signal for resetting the entire unit (negative logic 4ms or more) (2) Output signal TTL is utilized for all output signals. The output is pulled up with 3.3 kΩ resistance.
iDP3110 User's Manual • Output [ Printer side ] [ Host side ] (4) Timing chart 1) Timing for data entry and printing T1 T2, T3 T4 0.5 µs MIN 1 µs MIN 2 µs TYPE (5) Data receiving Printer is capable of accepting data from the host while the BUSY signal is in the “LOW” state. Printer cannot accept data when the signal is “HIGH”.
iDP3110 User's Manual 6. SERIAL INTERFACE 6.1 Specifications 1) Synchronization 2) Baud rate 3) Word configuration : Asynchronous : User selection, 4,800; 9,600 Baud / sec : Start bit 1 bit : Data bit 8 bit : Stop bit More than 1 bit 4) Signal polarity RS-232C * Mark = Logic “1” (-3 to –12V) * Space = Logic “0” (+3 to +12V) TTL(RESET) * H level = Logic “1” (refer to (3), section 6.
iDP3110 User's Manual 6.2 Connector Pin Assignment SIGNAL SIGNAL PIN NAME 1 FG 7 GND 3 RD 20 DTR 23 RESET SIGNAL DIRECTION HOST-PRINTER → ← → FUNCTION RS232C TTL Frame ground Signal ground Received data Printer BUSY signal Printer reset signal Note: 1. Signals for RS-232C are based on EIA RS-232C level. Applicable connector (D-Sub connector) Printer : 17LE-13250 (Anphenol equivalent) Cable : 17JE-23250 (Anphenol equivalent) 6.
iDP3110 User's Manual 3) RESET Signal resets the entire printer. (More than 4ms.) 4) FG Frame ground 5) GND Common ground for the circuit.
iDP3110 User's Manual (3) Electrical characteristics 1) RS-232C circuit Input (RD) [PRINTER] [HOST] MAX 232 equivalent Mark = (-8V) : Stop bit Space = (+8V) : Start bit Output (DTR) MAX 232 equivalent DTR (-8V) when BUSY (+8V) when READY 2) TTL circuit Input (RESET) 7HC14 equivalent CITIZEN Set to LOW when reset 17
iDP3110 User's Manual 7. DIP SWITCH SETTING 7.1 Serial Interface Type Switch Functions NO. 1 Character direction selection 2 Baud rate selection 3,4 Not used OFF ON Normal character 9600 BPS Inverted character 4800 BPS OFF ON Normal Character CR Inverted character LF Shipping Setting OFF ON OFF 7.2 Parallel Interface Type Switch Function NO.
iDP3110 User's Manual 8. PRINT CONTROL FUNCTION 8.1 Control Command (1) (2) (3) Print command (CR or LF) In case of initiate parallel transmission, select code CR (0DH) or LF (0AH) on the DIP switch 2. If the selected code (CR or LF) is input, the data in the print buffer is printed and line feed is performed. When the serial interface is used, only the CR code becomes effective.
iDP3110 User's Manual (4) Power down function In order to reduce power consumption when printer is waiting for the operation, 2 power down modes triggered by the codes DC2 and DC3 are incorporated into this product. When the printer receives power down commands (DC2 or DC3), it switches to the power down mode after all entered data is printed out. a) DC2 (12H) Unit switches to power down mode when DC2 code is entered. Operation of the oscillator is not terminated.
iDP3110 User's Manual a) Line spacing setting command (ESC + A + n) Dot line space setting is determined by entering the code ESC +A + n. Initial setting is 2 dot line space. The n should be an even number in the range of 0 ≤ n ≤ 255. Note) If an old number is entered, the dot line is set to “n-1”. Continuous printing is enabled by specifying n = 0 or 1. b) Bit image printing (ESC + K + n1 + n2 + n3) By entering ESC + K + n1 + n2 + n3, print mode is switched from the text mode to bit image mode.
iDP3110 User's Manual As this printer prints out 4 dot lines as one unit, the lacking data is output as space once the data for 4 dot lines are read in or the output of data specified in n1, n2 and n3 has finished. Note 1) If n1 = 23 is specified in iDP3110-40 specification, 4 dots from the topmost dot (MSC DOT) become invalid. This is due to the fact that the output position for a single line consists of 180 dots.
iDP3110 User's Manual d) Character registration (ESC + & + A1 + A2) Individual patterns can be registered by entering the code ESC + & + A1 + A2, then entering the pattern data. A maximum of 8 characters can be registered, and any address in the range of 20H to FFH can be used for the registration. However, if a new pattern is registered in an address already in use, existing data is cleared and the newly entered data becomes valid.
iDP3110 User's Manual d-2) Multiple character registration By repeating the single character registration, a maximum of 8 characters can be registered. When defining multiple characters in a successive address (character code), register pattern data for a maximum of 8 characters by designation A1 as the starting address and A2 as the ending address.
iDP3110 User's Manual d-4) In case of iDP3110-40* (40 columns) specification Pattern data to be registered must consist of 7 bytes per character. That is, pattern data configured by a 7 × 8 dot matrix is broken up into 7 vertically positioned units each of which is represented by 1 byte of data. All together, 7 bytes of data are transmitted.
iDP3110 User's Manual 9. CHARACTER SET 9.1 Character code (In the following Table *1-*12 are the characters of the next page by a command, ECS + R + n.
iDP3110 User's Manual CITIZEN 27
iDP3110 User's Manual Individual Country Character Codes CITIZEN 28
iDP3110 User's Manual 10.
iDP3110 User's Manual CITIZEN 30
Information Systems Division CBM Bldg., 5-68-10, Nakano, Nakano-ku, Tokyo 164-0001, Japan Head Office Tel: (+81-3) 5345-7540 Fax: (+81-3) 5345-7541 20-990914-5000-0036-005.
