Service manual

PN 4237242
12-INDEX
INDEX
ERROR DETECTED (009) URA Board
Failure, 7.4-5, C.2-1
ERROR DETECTED (011) URA CMOS
Failure, 7.4-5, C.2-1
ERROR DETECTED (012) System Disk File
Corrupt, 7.4-5, C.2-1
ERROR DETECTED (016) System Disk File
Corrupt, 7.4-4
input/output voltage, 2.4-4
installation procedures, 4.8-2
jumper and switch settings, 4.8-2
jumper location and setting, 2.4-5, 4.9-1
keypad controller, 2.4-4
location, 2.2-3, 4.6-1, 4.8-2
part number, 8.1-6, 8.2-4
removal procedures, 4.8-1
Software Fatal Error, 7.4-2, 7.4-5
support circuitry, 2.4-4
System Control, 2.4-1
table showing adjustments, A.1-1
table showing switch and jumper settings, A.2-4
tools/supplies needed for replacement, 4.8-1
Unable to Create INF File, 7.4-5
Utility Timer circuit, 2.4-4
verification procedures, 4.8-2
User Resource Adapter card. See URA card
Utility Timer circuit
description, 2.4-4
location, 2.4-5
V
VAC ON signal
AC Power/Vacuum Relay card, 2.2-2, 2.2-5
location, 2.2-3
VACUUM ADJUST
description, 7.1-2
vacuum adjustment procedure
steps, 4.30-1
Vacuum Sensor card, 4.14-2
Vacuum Out of Range
description, 7.4-5, C.1-1
vacuum pump
AC Power/Vacuum Relay card, 2.2-5
installation procedures, 4.23-1
location, 2.2-4, 4.4-1
part number, 8.1-4, 8.2-3
removal procedures, 4.23-1
tools/supplies needed for replacement, 4.23-1
unpacking the instrument, 3.2-1
VACUUM ADJUST, 7.1-2
verification procedures, 4.23-1
vacuum regulator
adjustment, 2.3-9
description, 2.3-9
location on Fluidics Panel, 2.3-1
part number, 8.1-3, 8.2-2
Vacuum Sensor card
adjustments, 2.5-5
function, 2.5-4
input/output voltage, 2.5-4
installation procedures, 4.14-2
location, 2.2-3, 4.4-1
location of connectors, 2.5-6
part number, 8.1-3, 8.2-3
removal procedures, 4.14-1
Service Diagnostic, 7.3-1
solenoid valves, 2.5-4
table of test points, 2.5-6, A.2-4
test point locations, 2.5-6
tools/supplies needed for replacement, 4.14-1
vacuum adjustment procedure, 4.14-2
verification procedures, 4.14-2
VACUUM SENSOR signal
location, 2.4-5
VIC
description, 2.3-2
function, 2.5-4
part number, 8.1-4, 8.2-9
tube removal, 4.14-2
VOLTAGE READINGS
description, 7.1-2
W
warning
definition, 1.1-1
WBC APERTURE signal
table showing Sensor Preamp Adapter card
connections, 2.5-1
WBC bath
activity on power-up cycle, 2.1-6
description, 2.3-2
WBC PREAMP signal
table showing SPAD card connections, 2.5-9
WBC signal
table showing Sensor Preamp Adapter card
connections, 2.5-2