Service manual

PN 4237242
10-INDEX
INDEX
Serial 2 connector
function, 2.6-1
table of pinouts, 2.6-1
serial ports
Serial 1, 2.6-1
Serial 2, 2.6-1
table of pinouts, 2.6-1
verify operation of port, 4.6-4
Service Diagnostic
description, 7.1-2, 7.3-1
Diluter Panel solenoids, 4.25-1
diluter table, 2.1-2
interaction with Vacuum Sensor card, 7.3-1
Motor/Solenoid Driver card, 4.15-3
procedures, 7.3-1
table showing cycle, 7.3-1
verify operation of solenoid valves, 4.9-2
Service menu options
LATEX GAIN, 7.1-2
PULSE TEST, 7.1-2
REPLACE SYRINGE, 7.1-2
REVISION LEVELS, 7.1-2
Service Diagnostic, 7.1-2
VACUUM ADJUST, 7.1-2
VOLTAGE READINGS, 7.1-2
Service Report
procedures to generate, 7.2-1
sample Service Report, 7.2-1
software menu system
description, 2.1-2
hidden menu items for service, 2.1-2
software menu tree, 2.1-2
software menu tree
illustration, 2.1-2, A.5-1
software tables
diluter table, 2.1-2
function, 2.1-2
instrument cycling, 2.1-2
Software Timer Error, 7.4-4
solenoid controller
DRA card, 2.4-7
Solenoid Interconnect card
description, 2.3-8
location, 2.2-3, 4.4-1
part number, 8.1-4, 8.2-3
table of connectors, solenoids, LEDs, 2.3-8
solenoid valves
Vacuum Sensor card, 2.5-4, 2.5-5
solenoids
Diluter Panel, 2.3-2
DRA card, 2.4-6, 2.4-7
fluidic solenoids, 2.3-1, 2.3-4
Motor/Solenoid Driver card, 2.4-9
on Flex Connect card, 2.3-7
space requirements
description, 3.1-1
table showing space requirements, 3.1-1
SPAD card
aperture signal processing, 2.5-8
control functions, 2.5-7
control signals/commands, 2.5-7
description, 2.5-6
ERROR DETECTED (004) SPAD Board
Failure, 7.4-4, C.2-1
ERROR DETECTED (039) SPAD Board
Failure, 7.4-4, C.2-2
input connector, 2.5-9
installation procedures, 4.7-1
interaction with AT motherboard, 2.5-7
interaction with Linear Power Supply card, 2.5-7
interaction with Sensor Preamp Adapter
card, 2.5-6
interrupt selector, 2.5-9
jumper location and setting, 2.5-9
jumper setting, 4.7-1
jumper settings, A.2-4
location, 2.2-3, 4.6-1, 4.7-1
location of connectors, 2.5-9
octal DAC, 2.5-8
Oscillator circuit, 2.5-7
part number, 8.1-6, 8.2-4
power supply conditioning, 2.5-7
Power Supply Conditioning card, 2.5-7
PULSE TEST, 4.7-2, 7.1-2
removal procedures, 4.7-1
table showing adjustments, A.1-1
test pulse generator, 2.5-9
tools/supplies needed for replacement, 4.7-1
verification procedures, 4.7-2
special headings, 1.1-1
attention, 1.1-2
caution, 1.1-2
important, 1.1-2
note, 1.1-2
warning, 1.1-1
stepper motor, 7.4-2
DRA card, 2.4-6
location on Syringe Assembly, 2.3-6