Service manual

PN 4237242
6-INDEX
INDEX
K
keypad
8279 keyboard controller chip, 2.4-3
description, 2.6-1
input connector, 2.4-5
installation procedures, 4.10-2
interaction with URA card, 2.4-2
location, 2.2-3, 4.10-1
location of connectors, 4.10-1
part number, 8.1-6, 8.2-2
removal procedures, 4.10-1
replacement, 2.6-1
Software Fatal Error, 7.4-2, 7.4-4
tools/supplies needed for replacement, 4.10-1
verification procedures, 4.10-2
verify operation, 4.8-2
keypad controller
description, 2.4-3
Keypad Failure, 7.4-2
L
LATEX GAIN
description, 7.1-2
latex gain adjustment procedure
Linear Power Supply card, 2.2-7
PMI recommendations, 5.2-2
LEDs
Hgb LED, 2.2-8, 2.3-2
Hgb LED current, 2.2-1, 4.13-3
Motor/Solenoid Driver card, 2.4-9
on Flex Connect card, 2.3-7
Solenoid Interconnect card, 2.3-8
limits
amplifier noise, table of, A.1-1
calibration factors, table of, A.1-1
Linear Power Supply card
description, 2.2-6
Hgb LED, 2.2-8
installation procedures, 4.13-2
interaction with Sensor Preamp Adapter
card, 4.13-3
interaction with SPAD card, 2.2-7
jumper locations and settings, 2.2-7, 4.13-1
jumper settings, 2.2-8, 4.13-2
latex gain adjustment procedure, 2.2-7
LED locations, 2.2-7
location, 2.2-3, 4.4-1, 4.13-2
location of test points and jumpers, 4.13-2
part number, 8.1-3, 8.2-3, 8.2-5
removal procedures, 4.13-1
table of test points, 2.2-8, A.2-2
table showing jumper settings, A.2-2
test point locations, 2.2-7, 4.13-1
tools/supplies needed, 4.13-1
verification procedures, 4.13-3
verify voltages, 4.11-2
lower chassis
opening, 2.2-3
lyse pump
description, 2.3-8
Fluidics Panel, 2.3-8
location on Fluidics Panel, 2.3-1
Motor/Solenoid Driver card, 2.4-9
LYSE PUMP signal
function, 2.4-9
lyse system
troubleshooting, 2.3-8
lyse volume adjustment/verification procedure
tools/supplies needed, 4.31-1
when to perform, 4.31-1
M
manual
conventions, 1.1-2
organization, 1.1-1
scope, 1.1-1
special headings, 1.1-1
manuals, customer
part numbers, 1.1-1
MIX
description, 7.1-1
Motor
Motor/Solenoid Driver card, 2.4-9
Motor/Solenoid Driver card
description, 2.4-8
installation procedures, 4.15-1
interaction with DRA cards, 2.4-8, 2.4-9
jumper locations and settings, 4.15-2
LED, 2.4-9
location, 2.2-3, 4.4-1
lyse pump, 2.4-9
part number, 8.1-3, 8.2-3
POWERFAIL signal, 2.4-10
removal procedures, 4.15-1
Service Diagnostic, 4.15-3
solenoid driver, 2.4-9
System Control, 2.4-1