Service manual

PN 4237242
INDEX-3
INDEX
D
Data Acquisition section
functional relationship, 2.1-1
Diagnostic Data Acquisition circuit
description, 2.4-4
diluent reservoir
description, 2.3-7
location on Fluidics Panel, 2.3-1
Diluter Functions menu options
CLEAN BATHS, 7.1-1
CLEAR APERTURES, 7.1-1
DISPENSE LYSE, 7.1-1
DRAIN, 7.1-1
MIX, 7.1-1
RINSE, 7.1-1
Diluter Panel
aperture system, 2.3-2
components, 2.3-2
description, 2.3-2
fluidic solenoids, 2.3-1, 2.3-4
Hgb LED, 2.3-2
interaction with Sensor Preamp Adapter
card, 2.3-2
location of components, 2.3-2
location on Fluidics Panel, 2.3-1
parts explosion, 8.2-8
RBC bath, 2.3-2
solenoids, 2.3-1, 2.3-4
sweep-flow system, 2.3-2
VIC, 2.3-2
WBC bath, 2.3-2
Diluter Panel solenoids
installation procedures, 4.25-1
interaction with Solenoid Interconnect
card, 4.25-1
removal procedures, 4.25-1
Service Diagnostic, 4.25-1
tools/supplies needed for replacement, 4.25-1
verification procedures, 4.25-1
Diluter Resource Adapter card. See DRA card
diluter table
aspiration cycle, 2.1-5
function, 2.1-2
power-up cycle, 2.1-6
Service Diagnostic, 7.1-2
timing chart, 2.1-4
troubleshooting using, 2.1-4
DISPENSE LYSE
description, 7.1-1
display
description, 2.6-1
installation procedures, 4.10-2
interaction with URA card, 2.4-2
location, 2.2-3, 4.10-1
location of connectors, 4.10-1
part number, 8.1-6, 8.2-2
removal procedures, 4.10-1
tools/supplies needed for replacement, 4.10-1
troubleshooting, 2.6-1
verification procedures, 4.10-2
verify operation, 4.8-2
display controller
description, 2.4-3
URA card, 2.4-3
Display Memory Read/Write Error
description, C.3-1
Document Control Numbers (DCN)
for schematics/diagrams included in this
manual, 6.1-1
for schematics/diagrams not included in this
manual, 6.1-1
DRA card
components, 2.4-6
description, 2.4-6
ERROR DETECTED (003) DRA Board
Failure, 7.4-2, C.2-1
installation procedures, 4.9-2
interaction with AT motherboard, 2.4-7
interaction with Motor/Solenoid Driver
card, 2.4-6
jumper locations, 2.4-8
jumper locations and settings, 4.9-1
jumper settings, 4.9-2, A.2-2
location, 2.2-3, 4.6-1, 4.9-2
motor controller, 2.4-6
part number, 8.1-6, 8.2-4
removal procedures, 4.9-1
solenoids, 2.4-6, 2.4-7
stepper motor, 2.4-7
stepper motors, 7.4-2
support circuitry, 2.4-7
System Control, 2.4-1
table of jumper settings, 2.4-8, A.2-2
table of output connectors, 2.4-7
tools/supplies needed for replacement, 4.9-1
verification procedures, 4.9-2
DRAIN
description, 7.1-1
Drain, 2.1-6