Service manual

PN 4237242
INDEX-1
INDEX
Symbols
+24 V POWER ON signal
location, 2.2-6
on +24 V power supply, 2.4-9
+24 V power supply
+24 V POWER ON signal, 2.2-6, 2.4-9
adjustments, 2.2-6
description, 2.2-6
ERROR DETECTED (015) Power Supply
Failure, 4.12-3, 7.4-3, C.2-1
ERROR DETECTED (027) Aspirate Syringe
Failure, 7.4-1, C.2-1
fuses used, 2.2-6
installation procedures, 4.12-2
interaction with AC Power/Vacuum Relay
card, 2.2-1
interaction with Power Supply Conditioning
card, 2.5-7
location, 2.2-3, 4.4-1, 4.12-1
location of connections, 4.12-1
part number, 8.1-3, 8.2-3, 8.2-5
POWERFAIL signal, 2.2-6, 2.4-10, 7.4-3
removal procedures, 4.12-1
replacement, 2.2-6
schematics, 2.2-6
table showing adjustments, A.1-1
tools/supplies needed for replacement, 4.12-1
verification procedures, 4.12-3
Numerics
8042 - Gate A20 Failure
description, C.3-1
A
A/D converter
verify operation, 4.8-2
AC Power/Vacuum Relay card
fuses used, 2.2-2, 4.11-1
installation procedures, 4.11-1
interaction with AT power supply, 2.2-2, 2.2-5
interaction with Linear Power Supply card, 2.2-2
jumper, 2.2-5
jumper settings, 3.2-1
location, 2.2-3, 4.4-1
part number, 8.1-3, 8.2-3
removal procedures, 4.11-1
table showing connectors and line input
ranges, A.2-1
test point and jumper locations, 2.2-3
test point readings, 2.2-5, A.2-1
tools/supplies needed for replacement, 4.11-1
VAC ON signal, 2.2-2, 2.2-5
verification procedures, 4.11-2
Ac Select switch
AT power supply, 2.2-2
switch settings, 3.2-1, 4.5-1
accessibility requirements
description, 3.1-1
accessing the Service Diagnostic
procedures, 4.2-1
adjustments, table of, A.1-1
AIM
criteria results, 7.2-1, 7.2-2
description, 7.2-3
AIM adjustment procedure
PMI recommendations, 5.2-2
steps, 4.28-1
amplifier noise limits
table showing, A.1-1
aperture, bath and Aperture Electrode module
installation procedures, 4.24-2
interaction with Sensor Preamp Adapter
card, 4.24-2
location of components, 4.24-1
removal procedures, 4.24-1
tools/supplies needed for replacement, 4.24-1
verification procedures, 4.24-3
aspiration cycle
table of timing activities, 2.1-5
AT motherboard
AMIBIOS beep codes, C.3-1
description, 2.4-1
ERROR DETECTED (013) CPU Fatal
Error, 7.4-1, C.2-1
installation procedures, 4.6-2
jumper locations, 2.4-1, 4.6-3
jumper settings, 2.4-1, A.2-1
location, 2.2-3, 4.6-1
removal procedures, 4.6-1
System Control, 2.4-1
table of switch and jumper settings, 2.4-1
tools/supplies needed for replacement, 4.6-1
verification procedures, 4.6-3
AT power supply
Ac Select switch, 2.2-2
description, 2.2-1
installation procedures, 4.5-1
location, 2.2-3