Technical information

ManualsBrandsCitizen ManualsGadgetsE76

MODELS – FC00**

LADIES’ WORLD TIME A•T

Mvmt. Cal. No. H82*

Time Zone Scale

Secondary (Dual) Time/

Alarm Minute Hand

Lower Right Button (A)

Upper Right Button (B)

Crown

Primary Time

Minute Hand

Function Hand

Primary Time

Hour Hand

24-Hour Hand

Second Hand

Charge Level/

Day of Week Scale

FEATURES

•

Light-Powered

•

Atomic Timekeeping

•

World Time

•

Perpetual Calendar

•

Power Reserve Indicator

•

Dual Time

•

Alarm

BENEFITS

•

Environmentally Clean Energy Source

•

Radio-Controlled Accuracy

•

Time Adjustment in 26 Time Zones

•

Accurate to the Year 2100

•

Displays Remaining Charge

•

Second Time Zone

•

Daily Alarm

Please view our interactive setting

instructions at www.citizenwatch.com

NOTE: Under normal conditions, this watch will

receive radio signals to automatically update the time

and calendar. There may be conditions in which the radio

signal cannot be received. If a signal cannot be received,

the watch will operate normally, but not sync with the

radio signal.

NOTE: After a complete loss of charge or an abnormal

display or function is noticed, an ALL RESET and

0-POSITIONING PROCEDURE must be followed.

Be sure to set the time and date after performing

these procedures.

RADIO RECEPTION

The watch will receive radio signals both automatically

and on-demand. Both the primary (home) time and

calendar will be based on the current time zone chosen

within the radio signal reception area.

Automatic reception occurs ﬁrst at 2:00 AM and

3:00 AM. If the 2:00 AM reception is successful,

the 3:00 AM reception attempt will not occur.

The “on-demand” feature allows the user to activate

radio reception manually. However, depending on

the time of day, weather, radio interference, etc., the

on-demand feature may not result in a successful radio

signal update and the watch may have to be manually

set, such as when changing radio signal zones.

NOTE: Based on signal strength, it can take from

2 to 30 minutes to complete the radio reception update

process. During the update process, the watch must

not be moved otherwise the transmission signal may

be interrupted resulting in an unsuccessful time/

calendar update.

For in-depth instructions on the radio reception feature,

please refer to your owners guide.

ALL RESET AND 0-POSITIONING PROCEDURE

•

Pull the crown out two ‘clicks.’

•

Simultaneously press and hold the upper right (B)

and lower right (A) buttons for 4 seconds, then

release. (Following a “beep” tone, the hands and

date will move back and forth, indicating a

successful ALL RESET).

•

Rotate the crown in either direction so the

dual time hour and minute hands (6:00 sub dial)

are pointing to ‘24’ (straight up).

•

Press and release the upper right button (B). The function

hand (12:00 sub dial) will then move slightly indicating the

function hand and date of month may be set.

NOTE: Depending on the position of the primary time

hour and minute hands, the primary time second hour

and minute hands may rotate to show a clear view of

the 12:00 sub dial.

•

Rotate the crown clockwise or counterclockwise so

that the date is centered between 31 and 1, and the

function hand (12:00 sub dial) is pointing to Sunday.

•

Press and release the upper right button (B). The

primary time minute and hour hands will move slightly.

•

Rotate the crown so that the primary time hour and

minute hands are pointing to the 12:00 position

(straight up).

•

Press and release the upper right button (B). The

second hand will move slightly.

•

Rotate the crown so that the second hand is pointing

to the 12:00 position (straight up).

•

Push the crown in two ‘clicks.’ You must now set the

primary time and perpetual calendar.

TO SET THE PRIMARY (HOME) TIME AND

PERPETUAL CALENDAR

NOTE: After receiving a radio signal, the primary (home)

time and date will be automatically set. The secondary

(dual time) is based off the primary (home) time.

There may be circumstances for which you need to

manually set the primary (home) time and date, such

as after an ALL RESET AND 0-POSITIONING.

•

Pull the crown out one ‘click’.

•

Rotate the crown clockwise or counterclockwise until

the second hand indicates the time zone nearest your

current location. The primary time hour, minute and

24-hour hands will rotate to the current time set in

memory for the chosen time zone.

•

Press and release the upper right button to turn

daylight saving time ‘ON’ (SMT) or ‘OFF’ (STD) as

indicated by the function hand (12:00 sub dial).

•

Press and hold the lower right button (A) for two

seconds to set daylight saving time to automatic

updating ( ) or manual updating ( ).

•

Press and hold the upper right button (B) for two

seconds then release. The second hand will rotate

to the 6:00 position.

•

Pull the crown out one additional ‘click’ to the time

setting position. The second and function hands will

rotate to the 12:00 position and the primary time hour

and minute hands will move slightly indicating the

time may be set.

•

Rotate the crown to set the correct time for the

chosen time zone. Be sure to pay attention to the

24-hour hand (9:00 sub dial) to ensure the proper

AM or PM time is set.

•

Press and release the upper right button (B). The

function hand (12:00 position) will rotate slightly

indicating the date of month may be set.

•

Rotate the crown clockwise or counterclockwise to

set the current date of month. NOTE: The function

hand (12:00 sub dial) rotates 5 times for each change

of date.

•

Press and release the upper right button (B). The

function hand (12:00 sub dial) will rotate slightly

indicating the current day of week may be set.

•

Rotate the crown clockwise to set the current day

of week.

•

Press and release the upper right button (B). The

second hand will rotate slightly indicating the month

and leap year may be set. Referring to the graphic

below, rotate the crown to set the current month and

leap year.

•

Press and release the upper right button (B). Rotate

the crown clockwise to set the current minute.

•

Push the crown in two ‘clicks’. This completes setting

the time and calendar.

TO CHECK THE ACTIVE PRIMARY AND

SECONDARY (DUAL TIME) ZONES

•

With the crown in the closed position next to the

case, press and release the upper right button (B).

The primary (home) time zone will be displayed

•

Press and release the upper right button (B). The

secondary (dual) time zone will be displayed.

•

Press and release the upper right button (B) to

resume normal operation.

TO CHANGE PRIMARY (HOME) TIME ZONE

•

Pull the crown out one ‘click’. The second hand will

rotate to indicate the current primary (home) time

zone and the function hand (12:00 sub dial) will

rotate to indicate the current daylight saving.

•

Rotate the crown to change time zones.

•

If needed, press and release the upper right

button (B) to change the daylight saving time

setting to ‘ON’ (SMT) or ‘OFF’ (STD) as indicated

by the function hand (12:00 sub dial).

•

Press and hold the lower right button (A) for two

seconds to set daylight saving time to automatic

updating ( ) or manual updating ( ).

•

Push the crown in one click. This completes changing

primary (home) time zones.

NOTE: The secondary (dual) time zone is based on the

time set for the primary (home) time zone.

NOTE: The secondary (dual) time (6:00 sub dial) is

displayed in a 24-hour format.

•

Pull the crown out one ‘click’. The second hand will

rotate to indicate the current primary (home) time

zone and the function hand will rotate to indicate

the current daylight saving time setting.

•

Press and release the lower right button (A).

The secondary (dual) time hands will rotate indicating

the secondary (dual) time zone can be changed.

•

Rotate the crown to move the second hand to reflect

the desired secondary (dual) time zone.

•

If needed, press and release the upper right button

(B) to change the daylight saving time setting to ‘ON’

(SMT) or ‘OFF’ (STD) as indicated by the function hand

(12:00 sub dial).

•

Press and hold the lower right button (A) for two

seconds to set daylight saving time to automatic

updating ( ) or manual updating ( ).

•

Push the crown in one ‘click’. This completes

changing the secondary (dual) time zone.

For instructions on using additional features of the

World Time A

•

T please refer to the full instruction

manual or the technical support section on our website

at www.citizenwatch.com.

January

February

March

April

May

June

December

July

August

September

October

November

Month of Year

Leap Year Setting

Leap year

1 year past leap year

2 years past leap year

3 years past leap year

Secondary (Dual) Time/Alarm

Hour Hand (24-Hour Format)

NOTE: Please be sure the second hand is moving in

one second increments. This indicates the watch is

properly charged.

•

Check digital display II for charge level.

If additional charging is needed, see the

instruction manual for guidance.

•

The analog time (large hour, minute and 24-hour

hand) cannot be set independently of the digital

time and the digital time must be set FIRST in order

to set the analog time.

NOTE: If you suspect a malfunction, ﬁrst check the

0-position of the hands. Turn the crown to the CHR

mode. Pull the crown out two ‘clicks.’ If the hands do not

point to the 0-position, follow the 0-POSITIONING check

and correction. If the watch should reach a no charge

state and is recharged or displays something improperly,

an ALL RESET PROCEDURE must be performed.

ALL RESET PROCEDURE

•

Turn the crown to set the mode hand to the

chronograph (CHR) mode.

•

Pull out the crown to the second ‘click’ (0-position

correction mode).

•

The second, minute, hour, 24-hour, and UTC analog

time indicator hands move back and forth.

•

UTC analog time Indicator hand rapidly advance to

the 0-position stored in memory.

•

Press the upper (A) and lower right (B) buttons

simultaneously, then release. All segments of both

digital displays I and II are shown when either of

the buttons is released.

•

These fully lit displays are canceled when the

crown is returned to the normal position.

•

After canceling, a confirmation tone is sounded

after which each of the hands performs a

demonstration movement in the order of the

second, minute, UTC analog time indicator and

24-hour hands to indicate that the ALL RESET

PROCEDURE is finished.

•

After the demonstration movement, pull the crown

out to the second ‘click’ to switch the watch to the

0-position setting state. Set the 0-position of the hands.

0-POSITIONING CHECK AND CORRECTION

•

Turn the crown clockwise or counterclockwise to

move the mode hand to chronograph (CHR) position.

•

Pull the crown out two ‘clicks’ to go to 0-position

correction mode. All hands must indicate 0-position

(12:00 for hour hand and 24:00 hours for AM/

PM hand). If not, turn the crown clockwise to

advance the hour and 24-hour hands, or turn crown

counterclockwise to move them backward. Make

sure the 24-hour hand is set to 0-position as well.

•

Press and release the upper right button (A) to

change the minute hand. Turn crown clockwise to

move minute hand backward. Be sure UTC analog

time indicator is set to 24:00 hours. Press and

release the lower right button (B) to change the

second hand. Turn crown clockwise to move second

hand to the 0-position. Push crown in, return to time

mode and set times.

TO SET THE TIME

•

Turn the crown clockwise or counterclockwise to

move the Mode hand to the time (TME) position.

•

Press and release the upper right button (A) to

change city code eastward or the lower right button

(B) to move westward.

•

When city code has been selected, pull crown out

two ‘clicks.’ Summertime (SMT) flashes. Press

and release the lower right button (B) to select

daylight or standard time (ON indicates daylight,

OF indicates standard). Hour hand will move

accordingly.

•

Press and release the upper right button (A). Seconds

will flash. Reset seconds by using the lower right

button (B).

•

Press and release the upper right button (A).

Minutes will flash. Turn the crown clockwise to

advance minutes or counterclockwise to move the

minutes backward. For fast advance, turn the crown

clockwise quickly two or three ‘clicks’ and minutes

will change rapidly until the crown is turned one

‘click’ in either direction to stop the advance.

•

Press and release the upper right button (A). Hours

will flash. Rotate the crown to change hours. Be

sure to set to correct AM or PM hours.

•

Press and release the upper right button (A). Hours

will flash. Press the lower right button (B) to select

AM/PM (12H) or military time (24H).

•

Push crown in to finalize setting of digital time. All

other cities are adjusted automatically when one

city is set to correct time, including the UTC analog

time indicator.

•

After you have set the digital time, if you want the

analog (hands) time to also indicate the time in your

zone (city code), press the upper right (A) and lower

right (B) buttons simultaneously. The digital time (your

time zone) will be switched to the analog display and

vice versa. City code and digital time and now be

changed to your time zone by using the upper right

button (A) (eastward) or the lower right button (B)

(westward). Both analog and digital time now match.

•

If you want a time zone different than that shown

on the digital display to be shown by the analog

time (hands), move the digital time to the desired

zone and repeat the switching function.

TO SET THE CALENDAR

•

Turn the crown clockwise or counterclockwise to

move the Mode hand to the calendar (CAL) position.

•

Press and release the upper right button (A) to

change city code eastward or the lower right button

(B) to move westward.

•

When city code has been selected, pull crown

out two ‘clicks.’ Month (numeric) will flash. Turn

the crown clockwise to advance month number

or counterclockwise to move the month (numeric)

backward. For rapid advancement, turn the crown

clockwise quickly two or three ‘clicks’ and month

(numeric) will change rapidly until the crown is

turned one ‘click’ in either direction to stop the

rapid advancement.

•

Press and release the upper right button (A).

Date will flash. Use the crown in the same manner

as you used to set the month to correct the date.

•

Press and release the upper right button (A).

Year will flash. Use the crown in the same manner

as you used to set the month to correct the year.

•

Push the crown in to finalize calendar setting.

Year will disappear and day will be shown instead.

TO SET THE ALARMS

•

Turn the crown clockwise or counterclockwise to

move the Mode hand to alarm 1 (AL-1) position.

•

Press and release the upper right button (A) to

change city code eastward or the lower right button

(B) to move westward.

•

When city code has been selected, pull the crown

out two ‘clicks.’ Alarm setting display flashes. Press

the lower right button (B) to set alarm ON or OFF.

•

Press and release the upper right button (A). Hours

will flash. Turn the crown clockwise to advance

the hours or counter clockwise to move the hours

backward. For fast advancement of the hours, turn

the crown clockwise quickly two or three ‘clicks’

and hours will change rapidly until the crown is

turned one ‘click’ in either direction to stop the

rapid advancement.

•

Press and release the upper right button (A).

Minutes will flash. Correct the minutes by using the

crown in the same manner used to set the hours.

•

Push the crown in to finalize alarm setting. Alarms

2 and 3 are set in the same way as alarm 1. When

either alarm sounds, press any button to stop

sounding. When the upper right (A) and lower right

(B) buttons are pushed simultaneously in alarm

mode, the alarm monitor sounds.

•

While in alarm mode, the alarm can also be set to

ON or OFF by pulling the crown out one ‘click’ and

pressing the lower right button (B).

TO USE THE CHRONOGRAPH

•

Turn the crown clockwise or counterclockwise to

move the mode hand to chronograph (CHR) position.

•

Press and release the upper right button (A) to start

or stop time measurement.

•

While chronograph is running, press the lower right

button (B) for split time. Display now shows elapsed

time for 10 seconds while continuing to measure

elapsed time internally. After 10 seconds, display

picks up counting at the true elapsed time and

continues running until the lower right button (B)

is pressed for split time again, or the upper right

button (A) is pressed to stop.

After the chronograph is stopped, press the lower right

button (B) to reset to 0.

For additional features and instructions, please

refer to the full instruction manual or our website

at www.citizenwatch.com.

FEATURES

•

Light-Powered

•

Auto and Manual Power Saver

•

Power Reserve Indicator

•

World Time

•

Personalize Time Zone (One City)

•

Analog/Digital Displays

•

Perpetual Calendar

•

3 Alarms

•

Chronograph

•

60-Minute Countdown Timer

•

Universal Coordinated Time (UTC) Display

BENEFITS

•

Environmentally Clean

Energy Source

•

Displays Remaining Charge

•

Time Adjustment in 30 Time Zones

•

Your Own Time Zone

Time at a Glance

•

Shows Month, Day and Date

•

Accurate to the Year 2100

•

Alarm for Every Occasion

•

1/100-Second Chronograph

Measures up to 24 Hours

•

Sound Signal When Time is Up

•

Instant Reference

MODELS – JR30** SKYHAWK

Mvmt. Cal. No. C650 + C651

Mode Hand

Crown

UTC Analog Time

Indicator

24-Hour Hand

Digital Display II

Digital Display I

Upper Right

Button (A)

Lower Right

Button (B)

Please view our interactive setting

instructions at www.citizenwatch.com