Technical information

44
|
|
45
Leap year
1 year past leap year
2 years past leap year
3 years past leap year
MODELS – BL5***
PERPETUAL CALENDAR CHRONOGRAPH
Mvmt. Cal. No. E82*
FEATURES
•
Light-Powered
•
Time
•
Perpetual Calendar
•
Chronograph
•
Dual Time
•
Alarm
BENEFITS
•
Environmentally Clean Energy Source
•
Displays 12/24-Hour Systems
•
Accurate to the Year 2100
•
1/20-Second Chronograph
Measures up to 60 Minutes
•
Second Time Zone
•
Daily Alarm
Crown
24-Hour Hand
Chronograph Minute/
1/20-Second Hand
Mode Hand
Time Second/
Chronograph Second Hand
Upper Right
Button (B)
Lower Right
Button (A)
Minute Hand
Hour Hand
NOTE: If you suspect a malfunction or the hands are in
an incorrect position, first check the 0-position of the
hands by pulling the crown out one click and rotate it to
move the mode hand (6:00 sub dial) to indicate (CHR).
Pull the crown out an additional ‘click’ to the setting
position. If the hands and date do not move to the correct
0-positions (pointing straight up to 12:00 with the date
at ‘1’), it will be necessary to perform the ALL RESET and
0-POSITIONING procedures.
After a full recharge from complete power loss or
if abnormal operation is noted, an ALL RESET and
0-POSITIONING CORRECTION will be needed prior to
setting the time and calendar.
ALL RESET AND 0-POSITIONING PROCEDURE
•
Pull the crown out 1 ‘click.’ Turn the crown to set the mode
hand (6:00 sub dial) to the chronograph [CHR] position.
•
Pull the crown out an additional ‘click’ (0-position
correction mode). Each of the hands and date moves to
their respective 0-positions stored in memory and then
stop. (NOTE: this may take a few minutes to complete.)
•
Simultaneously press and hold the upper right (B)
and lower right (A) buttons for two seconds then
release. Following a confirmation tone, the minute,
chronograph second, and chronograph minute hands
will move back and forth slightly indicating the ALL
RESET procedure was successful.
•
Press and release the upper right button (B). The minute
hand will move slightly indicating the hour, minute and
24-hour hands may now be set to their 0-position.
•
Rotate the crown so that the hour, minute and 24-hour
hands are pointing straight up (12:00). (NOTE: the
24-hour hand moves in conjunction with the hour hand.)
•
Press and release the upper right button (B). The
second hand will move slightly indicating it may now
be set to its 0-position. Rotate the crown to move the
chronograph second hand to the 12:00 position.
•
Press and release the upper right button (B). The
chronograph minute hand (upper right sub dial) will
move slightly indicating it and the date are active for
0-positioning.
•
Rotate the crown to set date of the date of month to
‘31.’ (Rotating the crown quickly will engage the rapid
advance function. To stop the rapid advance function,
rotate the crown one ‘click’.)
•
Continue to rotate the crown slowly until ‘1’ is shown
in the center of the date window and the chronograph
minute hand (upper right sub dial) indicates 12:00.
•
Push the crown in two ‘clicks’ to the closed position
next to the case. This completes the 0-positioning
procedure. You must now set the time and calendar.
TO SET THE TIME AND CALENDAR
•
Pull the crown out 1 ‘click’ and rotate the crown
clockwise or counterclockwise to move the mode
hand (6:00 sub dial) to the time (TME) position.
•
Pull the crown out one an additional ‘click’
(two ‘clicks’ out) to the time/calendar setting position.
•
Press and release the upper right button (B). The
second hand will move to the 0-position set in
memory then stop. The minute hand will move
slightly indicating it is active for setting.
NOTE: If the second hand stops at any other position, you must
perform an ALL RESET and 0-POSITIONING CORRECTION.
•
Rotate the crown clockwise (right) to set the current
time. Pay particular attention to the position of the
24-hour hand (upper left sub dial) to ensure the correct
AM or PM time is set. (Rotating the crown quickly will
engage the rapid advance function. To stop the rapid
advance function, rotate the crown one ‘click’.)
•
Press and release the upper right button (B). The
chronograph minute hand (upper right sub dial) will
move slightly indicating the leap year designation
may be set.
•
Rotate the crown clockwise (right) to adjust the
chronograph minute hand (upper right sub dial)
to indicate the current leap year designation.
•
Press and release the upper right button (B). The
second hand will make a full rotation and stop at
the last month of year in memory indicating the
month of year may now be set.
•
Rotate the crown clockwise to align the second hand
to indicate the current month of the year. Each hour
location will correspond to a month.
•
Press and release the upper right button (B).
The chronograph minute hand (2:00 sub dial) will
make one rotation counterclockwise then return
indicating the date of month may be set.
•
Rotate the crown clockwise to set the current date of
the month. (NOTE: the function hand (upper right sub
dial) will rotate 4 revolutions for each date change.)
•
Press the crown in two ‘clicks’ to the closed position next
to the case. This completes setting the time and calendar.
TO USE THE CHRONOGRAPH
The chronograph will measure up to a maximum of 59
minutes and 59.99 seconds in 1/20-second increments
and then stop at the 0-position. NOTE: Be sure to reset
the chronograph after each use to conserve power.
•
Pull the crown out one ‘click’ and rotate it to move the
mode hand (6:00 sub dial) to the chronograph (CHR)
position. The second hand will move to the 12:00
position indicating the watch is in chronograph mode.
•
Push the crown in one ‘click’ to the closed position
next to the case.
•
Press and release the upper right button (B) to start or stop
the chronograph. A confirmation beep will signal when
the upper right button (B) is pressed. While measuring the
elapsed time, the chronograph minute hand (2:00 sub dial)
records elapsed minutes and 1/20th of a second. After
the chronograph is stopped, if the lower right button
(A) is pressed and held, the chronograph minute hand
will indicate the 1/20 of a second.
•
To return the chronograph hands to 12:00 after the
chronograph is stopped, press and hold down the
upper right button (B) for approximately 2 seconds.
TO USE THE ALARM
Once set and activated, the alarm will sound for 15
seconds at the set time every 24-hours based on the
time set. It cannot be set for the travel (LTM) time.
•
Pull the crown out 1 ‘click’ and rotate the crown
clockwise or counterclockwise to move the mode
hand (6:00 sub dial) to the alarm (ALM) position.
The hands will move to the following positions:
•
Second hand: moves to the 30 second (6:00) position
hour, minute and 24-hour hands: moves to indicate
the last set alarm time.
•
Pull the crown out an additional ‘click’ (two ‘clicks’
out) to activate the alarm setting mode.
Rotate the crown clockwise (right) to set the desired
alarm time. Be sure to pay particular attention to the
24-hour hand (upper left sub dial) to ensure the correct
AM or PM time is set.
•
To activate the alarm, press and release the upper
right button (B) to change the position of the
chronograph second hand to indicate ‘on’ (8:30) or
‘off’ (7:30).
•
Push the crown in two ‘clicks’ to the closed position
next to the case. This completes the alarm setting.
TO ACTIVATE OR DEACTIVATE THE ALARM
Once the alarm time is set, you may wish to activate or
deactivate the alarm.
•
Pull the crown out 1 ‘click’ and rotate the crown
clockwise or counterclockwise to move the mode
hand (6:00 sub dial) to the alarm (ALM) position.
•
Pull the crown out an additional ‘click’ (two ‘clicks’
out) to activate the alarm setting mode.
•
Press and release the upper right button (B) to change
the position of the second hand to indicate ‘on’ (8:30)
or ‘off’ (7:30).
•
Press the crown in two ‘clicks’ to the closed position
next to the case. This completes the alarm activation/
deactivation procedure.
For additional features and instructions, please
refer to the full instruction manual or our website
at www.citizenwatch.com.
Please view our interactive setting
instructions at www.citizenwatch.com
NOTE: If you suspect a malfunction, first check the
0-position of the hands as outlined in the 0-positioning
CHECK PROCEDURE. If the hands and date do not move
to their respective 0-positions, it will be necessary to
set them for proper operation.
After a full recharge from complete power loss or
if abnormal operation is noted, an ALL RESET and
0-POSITIONING CORRECTION will be needed.
The second hand on this watch moves in one second
increments to indicate that the charge level is sufficient
for normal time keeping operation. If it is not moving in
one second increments, be sure to charge your watch
fully as outlined in your Instruction Manual.
0-POSITIONING CHECK PROCEDURE
•
Pull the crown out one ‘click.’
•
Turn the crown so that either tip of the mode hand
is pointing to the local time mode (L-TM).
•
Push the crown back in one ‘click’ to the closed
position next to the case.
•
Press the upper right button (A) for 10 or more
seconds until the hands move to the 0-position stored
in memory. Release the upper right button (A). The
correct 0 position for each hand is as follows:
– Hour, minute and second hand pointing to ’12:00’
– 24-hour hand pointing to ‘24’
– Function hand pointing to ‘SUN’
– Date indicating ‘1’
If any of the hands do not indicate their respective
0-position, it will be necessary to perform the all reset
and 0-positioning correction procedure.
•
Press the upper right button (A) to resume normal
operation in the local time mode.
ALL RESET AND 0-POSITIONING
CORRECTION PROCEDURE
•
Pull the crown out one ‘click.’
•
Turn the crown so that either tip of the mode hand
is pointing to the local time mode (L-TM).
•
Push the crown back in one ‘click’ to the closed
position next to the case.
•
When the hands have stopped moving, pull the crown
out two ‘clicks.’
•
Press the upper right (A) and lower right (B) buttons
simultaneously for two to three seconds, then
release. Following a confirmation tone, each of the
hands performs a ‘demonstration’ in the order of the
function, minute and second hands to indicate that
the ‘all reset’ of the movement has completed.
•
Press the upper right button (A). The minute hand
will move to indicate the hour, minute and 24-hour
hands can be set. Turn the crown clockwise or
counterclockwise to set the hour and minute hand to
12:00 and the function hand to ‘24’ (the 24-hour hand
moves in conjunction with the Hour hand and cannot
be set independently).
Turning the crown rapidly (‘clicking’ continuously two or
more times) causes the hands to advance continuously
until the crown is again turned.
•
Press the upper right button (A) again. The function
hand will move indicating that is the hand that
can now be set. Turn the crown clockwise or
counterclockwise so that function hand points to
‘SUN’ and the date is set for 1. Turning the crown
rapidly (‘clicking’ continuously two or more times)
causes the hand to advance continuously until the
crown is again turned.
•
Press the upper right button (A). The second hand will
move indicating the second hand can now be set.
•
Turn the crown clockwise to move the second hand to
the ‘12:00’ position.
•
Push the crown in two ‘clicks’ to the closed position
next to the case. This completes the all reset and
0-positioning correction.
•
Continue with to set the time.
TO SET THE TIME
•
Pull the crown out one ‘click.’
•
Turn the crown so that either tip of the mode hand
is pointing to the time mode (TME).
•
Pull the crown out an additional ‘click’ to the time
setting position. The second hand will move to the
12:00 position.
•
Turn the crown to change the position of the hour,
minute and 24-hour hands electronically. Turning
the crown clockwise moves the hands forward and
counterclockwise moves the hands backward. Turning
the crown quickly causes the hands to move in a
continuous or rapid set manner. Turning the crown one
‘click’ in either direction while the hands are in the
“rapid set” mode will cause the hands to stop.
•
Be sure to set time to the correct AM/PM by referring
to the 24-hour hand. After setting time, push the
crown in to finalize time setting.
TO SET THE CALENDAR
•
Pull the crown out one ‘click.’
•
Turn the crown so that either tip of the mode hand
is pointing to the calendar mode (CAL).
•
Pull the crown out an additional ‘click’ to the calendar
setting position. The function hand will move to
indicate the leap year set in memory. The positions
are as follows:
– ‘LY’= indicates the current year is a leap year
– ‘+1’ indicates 1 year past a leap year
– ‘+2’ indicates 2 years past a leap year
– ‘+3’ indicates 3 years past a leap year
Turn the crown clockwise or counterclockwise to set the
correct leap year position.
•
Press the upper right button (A). The second hand will
move to indicate the month stored in memory. Turn the
crown clockwise to set the current month.
•
Press the upper right button (A). The function hand
will move to the middle of the day indicator indicating
the date can be set. Turning the crown clockwise
will advance the date, while turning the crown
counterclockwise will move the date backward.
Turning the crown quickly causes the hands to move
in a continuous or rapid set manner. Turning the crown
one ‘click’ in either direction while the hands are in
the “rapid set” mode will cause the hands to stop.
Set the date for the current date.
•
Press the upper right button (A). The function hand
will move to the day of the week stored in memory.
Turn the crown clockwise or counterclockwise to set
the current day of the week.
•
Push the crown to the closed position next to the
case. This completes setting the calendar.
TO SET THE ALARM
The alarm is based on a 24-hour time period and can
be set to sound at the same time each day.
•
Pull the crown out one ‘click.’
•
Turn the crown so that either tip of the mode hand
is pointing to the alarm mode (ALM). The hour, minute
and 24-hour hands will move to the current alarm time
set position.
•
Pull the crown out an additional ‘click’ to the alarm time
setting position. The alarm will automatically be activated
and the Function hand will move to indicate ‘ON.’
•
Rotate the crown either clockwise or counterclockwise
to set the desired alarm time, paying close attention
to the 24-hour hand to ensure the proper AM or PM
alarm time is set.
•
Press the lower right button (B) to turn the alarm
ON or OFF.
•
Push the crown to the closed position next to the case.
TO SET THE LOCAL TIME
The local time (L-TM) function allows the time to be set
and displayed for a different time zone other than your
own. It can be set in 1 hour increments only.
•
Pull the crown out one ‘click.’
•
Turn the crown so that either tip of the mode hand is
pointing to the Local Time mode (L-TM).
•
Pull the crown out an additional ‘click’ to the local
time setting position.
•
Turn the crown clockwise to advance the time by one hour,
or counterclockwise to move the time back one hour.
•
Once you have the local time set, push the crown in
two ‘clicks’ to the closed position next to the case.
For additional features and instructions, please
refer to the full instruction manual or our website
at www.citizenwatch.com.
FEATURES
•
Light-Powered
•
Time
•
Perpetual Calendar
•
Alarm
•
Dual Time
BENEFITS
•
Environmentally Clean Energy Source
•
Displays 12/24-Hour Systems
•
Accurate to the Year 2100
•
Daily Alarm
•
Second Time Zone
MODELS – BL80**
CALIBRE 8700 SERIES
Mvmt. Cal. No. E870
Seconds/Minutes Track
Month Indicator Dial Ring
Second Hand
Mode Hand
Date
Function Hand
Minute Hand
Leap Year Indicator
Alarm ON/OFF Indicator
(hidden by minute hand)
Crown
Hour Hand
24-Hour Hand
Lower Right Button (B)
Day of Week Indicator
Upper Right Button (A)
Please view our interactive setting
instructions at www.citizenwatch.com