Technical information

28
|
|
29
CTB-050
Band Pin Pusher
$3.00 USD
$5.00 CDN
CTB-047
Replacement Kit
(3 Pins and Handle) for CTB-038
$3.00 USD
$5.00 CDN
CTB-052
Vise for Band
$18.50 USD
$23.50 CDN
BST-004/6
Replacement Pin 4/6mm for Sizing Tool
$2.85 USD
$3.75 CDN
BST-008MM
Replacement Pin 8mm for Sizing Tool
$2.85 USD
$3.75 CDN
CIT-SZTOOL
Plier Type Sizing Tool
$40.00 USD
$50.00 CDN
TO ORDER TOOLS:
1-800-321-1023, ext. 4234 (US)
1-800-263-7799 (CANADA)
CTB-038
Eccentric Pin Pusher
$6.50 USD
$8.50 CDN
BRACELET SIZING TOOLS AVAILABLE FROM CITIZEN
These specialty bracelet sizing tools can be ordered at the prices listed below directly from Citizen.
(These tools are only for sale. No co-op funds can be used.)
All prices are effective 7/2014 and are subject to change without notice.
SIZING TOOLS & INSTRUCTIONS
28
|
SP SPLIT PIN (“COTTER PIN” STYLE)
Disassembly
Recommended Tools
■
Citizen Sizing Tool CIT-SZTOOL
■
Tweezers
■
Jeweler’s Pliers
Disassembly Assembly
1. Place the bracelet in the sizing tool, with the
arrows pointing away from you. Align the pin
hole on the side of the bracelet with the Citizen
Tool sizing pin. Apply gentle pressure to start
removal of the pin.
2. Grasp the protruding pin with a pair of
jeweler’s pliers or tweezers to remove
the clip spring pin.
3. After the clip spring pin is removed, the
links may be separated. Repeat these
procedures to remove as many links as
required. Be sure to balance the links
removed from each side. If removing an
uneven amount of links, remove more links
from the 6:00 side of the bracelet. This will
help to “balance” the watch on the wrist.
1. Assembly is opposite of disassembly.
First connect the links together. Then
reinsert the clip spring pin in the opposite
direction of the arrows on the back side
of the bracelet, as far as it will go using
finger pressure.
2. After the clip spring pin is inserted in
the bracelet, use the flat end of a pair
of tweezers to push the clip spring pin
into the bracelet until the edge of the clip
spring is flush with the edge of the bracelet.
CS CLIP SPRING COUPLED TYPE
Recommended Tools
■
Small Screwdriver
■
Jeweler’s Pliers
■
Tweezers
1. Turn the bracelet upside down on a
padded work surface. Place the pointed
end of a pair of tweezers or the tip of a
screwdriver in the dimple of the clip spring
pin in the link. While pressing down on the
bracelet with your fingers to keep it from
moving, use gentle but constant pressure
to push the clip spring out of the bracelet
with the tweezers or screwdriver. Be sure
to push in the direction of the arrow on the
back of the bracelet.
2. Grasp the protruding pin with a pair of
jeweler’s pliers or tweezers to remove
the clip spring pin.
3. After the clip spring pin is removed, the
links may be separated. Repeat these
procedures to remove as many links as
required. Be sure to balance the links
removed from each side. If removing an
uneven amount of links, remove more links
from the 6:00 side of the bracelet. This will
help to “balance” the watch on the wrist.
1. Assembly is opposite of disassembly.
First connect the links together. Then
reinsert the clip spring pin in the opposite
direction of the arrows on the back side
of the bracelet, as far as it will go using
finger pressure.
2. After the clip spring pin is inserted in
the bracelet, use the flat end of a pair
of tweezers to push the clip spring pin
into the bracelet until the edge of the
clip spring is flush with the edge of
the bracelet.
Assembly
6. BRACELET SIZING GUIDE