English FOR DIGITAL BLOOD PRESSURE MONITOR MODEL CH-656C Español Português Italiano INSTRUCTION MANUAL Deutch - Eng 1 - Français M
CLEANING METHOD OF CUFF After cleaning the cuff with a neutral detergent, lightly rinse it with water and let it dry in the air. Hard rubbing or washing in a washing machine will cause air leakage. Also, be careful not to get water into the air hose. GENERAL REMARKS • If the cuff is to be deflated quickly, depress “POWER” switch. • The attached cuff is suited for a wrist circumstance of 13.5cm to 19.5cm.
• If you suffer from heart disease, high blood pressure or other circulatory disease, please consult your doctor first. • If you feel abnormal pressure of the cuff during use or any other irregularity, reduce the pressure by immediately switching off the power or removing the batteries and consult the sales outlet where purchased. • If you think the measured value is abnormal or if measuring makes you feel unwell, discontinue use and consult your doctor.
• Congestion, swelling, etc. may occur in some people. • If blood pressure is measured repeatedly, an accurate result will not be achieved. An interval of about 10 minutes should be allowed. • The memory is erased if the batteries are removed for replacement, etc. and a record should be kept of any necessary data.
Systolic blood pressure display section Battry cover Español Português Italiano Diastolic blood pressure/ Pulse display section English IDENTIFICATION OF PARTS M - Eng 5 - Français Memory recall switch Wrist cuff Deutch Power/Start switch
BATTERY REPLACEMENT 1. To use this unit, you must install batteries, ” will display and also If battery mark “ on the display, you must change two pieces of batteries. 2. Open battery cover as illustrated. Replace the new two pieces of batteries, matching the (+) and (–) polarities on each battery with the polarity marks on the case. 3. “LR03” batteries or equivalent is suitable for this blood pressure meter. • Pull the transparent ribbon to remove the batteries. MEASUREMENT PROCEDURES 1.
Measurement Procedures for People With a Weak Pulse • Apply the middle part of the wrist cuff to the artery in the wrist to measure blood pressure. Español Português Italiano 2. To start the Measurement English • Apply the wrist cuff to the wrist and make sure it is not too loose or too tight. If the wrist cuff is applied inappropriately, it may display an error or abnormal values. Pull the wrist tight and close the “Burr closure”. Wrist circumference: 13.5-19.5 cm.
The heart symbol flashes, and the buzzer sounds for 1 second. Once the measurement preparations are completed, the buzzer sounds three more times. If batteries become weak, “ ” mark is displayed and measurement is discontinued. Pressurization and measuring start. When a pulse is detected, the pressure value moves to the lower side of the display. At this time the mark “Q” flashes and buzzer beeps.
(1 second) Blood pressure values and pulse rate display alternatively on the display. Display of the measurement result will continue until power is turned off. Press the “POWER/START” switch to turn off. 4. Automatic power-off function If the unit is left on after measurement an automatic power-off function turns the power off after approximately 3 minutes. To continue measurement press the “POWER/START” switch turning the unit on.
5. Memory recall • When pressing the “Memory recall” switch, the memory cell number is displayed, then the stored measurement results (high/low blood pressure) are displayed. M • You can recall stored data by pressing the “Memory recall” switch, except when performing a measurement. • Up to 7 sets of measurement results can be stored in memory, and memory cell No. 1 is always used to store the newest set of results.
English 6. Memory clear function Deutch While the memory datum to be cleared are indicated and when the “Memory recall” switch is continued to push for 3 seconds, buzzer beeps and the memory datum are cleared.
DESCRIPTION OF DISPLAY MARKS DISPLAY MARK CONDITION / CAUSE CORRECTIVE ACTION The cuff was inflated to more than 280 mmHg. Exhaust the air with in the cuff. Pressurization is not possible Cuff winding has not been performed correctly. After winding the cuff over again, repeat measurement. The pulse could not be measured accurately. After again winding the cuff, conduct the measurement without moving. The arm moved during measurement. Repeat the measurement without moving the arm.
●CITIZEN is a registered trademark of Citizen Watch Co., Japan. Consumer Electronics Division CBM Bldg. 5F, 5-68-10, Nakano, Nakano-ku, Tokyo 164-0001, Japan Phone: (03)5345-7430 Fax: (03)5345-7431 E-mail: info-con@jcbm.co.
