English TM FOR DIGITAL BLOOD PRESSURE MONITOR Español INSTRUCTION MANUAL Português MODEL CH-485E Deutch Français English Español Português Deutsch - Eng 1 -
GENERAL REMARKS General remarks on blood pressure and blood pressure measurement 1. If the cuff is to be deflated quickly, depress “Exhaust button”. 2. The attached cuff is suited for an arm circumference of 22 cm to 32 cm. 3. When attaching the cuff, cuff tube should be placed on the inside of your arm on top of the arterial. 4. Self-measurement is no therapy! In no case the dosage of medicaments ordered by the doctor may be changed. 5.
Precaution for use Nature and frequency of maintenance: This product is designed for use over an extended period of time; however, it is generally recommended that it be inspected every two years to ensure proper function and performance. Reference European standard: Precaution for maintenance 1. Do NOT store the blood pressure monitor where it will be exposed to direct sunlight, high temperature (Over 60C), low temperature (below –20C), high relative humidity (over 95%) or in a dusty place. 2.
UNIVERSAL DESIGN The product has been developed through the concept of Universal Design to ensure safe and easy use for a wider range of users. The product, which is designed laying importance on Universal Design, adopts a product shape and color that conveys an image of “warmth” and “gentleness” and has functions that cope with human body, which are “easy to understand,” “safety in use" and “easy to use.
English IDENTIFICATION OF PARTS Time (Memory time) display section Data indicating section SET switch POWER/ START switch MEMORY switch Deutch Battery mark Insufficient pressure mark Measurement mark Português Diastolic blood pressure display section Pulse display section Alarm mark Español Systolic blood pressure display section Air hose socket Cuff Cuff holding pocket Air hose connector Air hose Battery cover RESET switch - Eng 5 - Français MODE switch
HOW TO LOAD BATTERIES (Batteries supplied with the unit should be loaded in compartment before putting the Blood pressure monitor in use.) (1) Open the cover of battery compartment. Pressing the hook down, pull the cover toward you to open. Hook Battery compartment Battery compartment cover Lug (projecting section) (2) Place batteries in the compartment. Put the batteries paying attention to the positive and negative terminal symbols + and –. (See the sketch shown on the battery compartment cover.
1. Initial state (when the batteries are loaded in the unit for the first time, carry out resetting operation) The alarm time, current time and calendar should be set in the written order. * Every press on “SELECT” switch selects a data item to be modified in the order shown below. The selected item flashes on and off. * Press “SET” switch to increase the indicated value in increments of one. Keep “SET” switch held pressed to carry out correction quickly.
3. Correcting the “minute” of an alarm time ● Press “SELECT” switch for one second or more to place the unit in the alarm-time minute correction state. ● Press “SET” switch to increase the minute of the alarm time in increments of one minute. 4. Correcting the “hour” of an alarm time ● After the completion of the alarm-time minute correction as described above, press “SELECT” switch to place the unit in the alarm-time hour correction state.
Español ● After the completion of the current-time minute correction as described above, press “SELECT” switch to place the unit in the current-time hour correction state. ● Press “SET” switch to increase the hour of the current time in increments of one hour. English 7. Correction of the “hour” of the current time Português 8. Correction of the “year” ● After the completion of the year correction as described above, press “SELECT” switch to place the unit in the month correction state.
11. Changeover of the “time system” ● After the completion of the day-of-the-month correction as described above, press “SELECT” switch to place the unit in the time system selection state. ● Every time “SET” switch is pressed, the 12-hour system (12H) and 24-hour system (24H) will be changed over. ● Press “SELECT” switch after activating the time system indication on the display to revert the display to the time indication. This completes the clock setting procedure. 12.
1. Put the cuff around your arm. English HOW TO MEASURE YOUR BLOOD PRESSURE 1. Remove the Velcro to unroll the cuff as illustrated. ● The cuff should be put on the bare arm or over a lightweight underwear. ● Draw the end of cuff to fit it on the arm and secure with Velcro. ● Carefully put the arm taking care to obtain adequate tightness, not too tight or loose. Adequate tightness is obtained when such an allowance that you can put a finger between the cuff and your arm is provided as illustrated left.
2. Measure your blood pressure in the correct posture Be sure to measure your blood pressure at the same time and in the same posture on a daily basis. ○ ○ ○ ○ ○ ○ ○ 1 Sit on a chair in a comfortable position, placing your arm on a table or the like to stretch out the portion from the elbow to the hand straight. 2 The most important point for the blood pressure measurement is to level the arm band to your heart. 3 Lightly open your hand on the table with palm up and relax your fingers.
Español ● Securely insert the air hose plug into the air hose socket of the main unit as illustrated. English 3. Insert the air hose plug into the main unit. Português Deutch 4. Start measurement. ● The Q mark comes on and the buzzer sounds for one second. ● The buzzer beeps three times and the Q mark goes out. Now, the pump activates. - Eng 13 - Français ● Press "POWER/MEASURE" switch.
● The Blood pressure monitor automatically carries out pressurization until the pressure that is best suited to the blood pressure measurement is reached. ● When the unit determines that an adequate pressure is not obtained, the unit starts pressurization again. [Manual pressurization] ● Keep “POWER/MEASURE” switch held pressed until the pressure value you want to stop pressurization is reached (approximately 40 mmHg higher than the maximal blood pressure).
Press “POWER/MEASURE” switch to revert the display to the time indication. Español ● When you want to stop measurement, press “POWER/ MEASURE” switch. The air in the cuff is exhausted to stop measurement. English 5. Português Deutch Store the cuff in the pocket. ● Wrap the air hose lightly on the cuff with the air hose plug inserted into the main unit. Then, put it in the cuff pocket. ● Place the unit. as a clock, at such a location that you can observe the display easily. - Eng 15 - Français 6.
AUTOMATIC CHANGEOVER FEATURE ● Press “POWER/MEASURE” switch after the completion of blood pressure measurement to revert the display to the time display. If you do not press the switch and leave the unit, the “Automatic changeover feature” of the unit will work approximately three minutes later to automatically revert the display to the time indication. If you leave the unit for three minutes without performing operations, the display will automatically changeover to the time indication.
● Press “MEMORY” call switch. English STEPS OF PROCEDURE TO BE TAKEN TO CALL UP DATA STORED IN MEMORY Español Português Deutch ● Press “MEMORY” call switch again. This calls up the memory number first, then the latest data on the display. ● Press “MEMORY” call switch again. This calls up the second latest data to the screen. In this way, every time you press this switch, the unit will give you the one previous data in sequence.
HOW TO DELETE DATA STORED IN MEMORY ● The data stored in memory can be deleted. ● Press “MEMORY” call switch to call up the data you want to delete to the display. Keep the switch held pressed for three seconds or more to delete the data. Then, the buzzer sounds to let you know the completion of deletion of the data. ● After the completion of data deletion, the average value of the whole data stored in memory will appear on the display.
The batries are dead. Change them with new ones. * For some batteries, the rough indication mark does not appear. RESETTING OPERATION ● When you put the Blood pressure monitor in use for the first time, be sure to press the RESET switch mounted on the back of the main unit to reset after loading the batteries in the compartment. ● If the main unit fails to work normally while it is in use, the normal state may be restored to the unit by carrying out resetting operation.
DESCRIPTION OF DISPLAY MARKS DISPLAY MARK CONDITION / CAUSE CORRECTIVE ACTION Measurement is begun, but the pressure was insufficient. Repeat measurement again. Appears when the blood pressure could not be measured accurately. (Some noises were detected by the movement of arm during measurement.) Repeat measurement again. Appears when the pulse could not be measured. First, exhaust air from the cuff, reapply the cuff properly and remeasure. Appears when batteries become weak. Replace the batteries.
Accuracy Pressure Pulse Pressure Pulse Pressure Marks Viewing Size Digit Size Switch Inflation Deflation Exhaust Rated Voltage Power Source Power Consumption Battery Life Automatic Power Off Function Memory Function Dimensions Weight Temperature Operating Environment Humidity Temperature Storage Environment Humidity Accessories * Specifications and design may be changed without any notice in the event of improvementsbeing made.
ABOUT “BLOOD PRESSURE” What is blood pressure ... The heart is a pump that circulates blood to different part of the body. Blood is pumped from the heart at a constant pressure into arteries. This pressure is called the arterial blood pressure, which represents, in general, blood pressure.
Why is the blood pressure measured at home different from that measured at a hospital? Blood pressure measured at home is reliable since it can be measured in a stable and relaxed condition. Doctors lay importance on blood pressure measurements taken at home. It is recommended to measure your blood pressure at the same time on a daily basis to record blood pressure variation and consult your family doctor instead of fluctuating between hope and fear at every rise and fall of your blood pressure.
BEFORE ASKING FOR REPAIR/INSPECTION ● Be sure to check the following before sending your Blood pressure monitor for repair/inspection. Phenomenon Point to be checked How to repair Check whether batteries are dead? Change the batteries with new ones and press RESET button referring to page 6. Check whether the orientation of the positive and negative terminals of batteries, is correct. Load the batteries in the correct orientation referring to page 6. Pressure does not arise.
