Service manual

ManualsBrandsCitizen ManualsComputer equipmentCD-S500S

DOT MATRIX PRINTER

CD-S500 Series

Service Manual

Rev. 1 (2005. 05)

NJ74905-01F

Summary of content (164 pages)

PAGE 1
DOT MATRIX PRINTER CD-S500 Series Service Manual Rev. 1 (2005.
PAGE 2
CD-S500 Series Introduction This manual is intended for in-field service personnel and explains maintenance procedures for Citizen Dot Matrix Printer CD-S500 series. Read and understand the contents described in this manual for appropriate maintenance. Features This printer is a dot matrix printer developed for use with various kinds of data communication terminals, POS terminals, and kitchen printers.
PAGE 3
CD-S500 Series Explanation of Models Models in this series are identified by the following model naming method.
PAGE 4
CD-S500 Series Contents Chapter 1 SAFETY INSTRUCTIONS 1-1 Conventions for Warning and Caution ................................................................................... 1-1 1-2 Precautions in Handling ......................................................................................................... 1-1 1-3 Precautions in Storage .......................................................................................................... 1-1 1-4 Precautions in Maintenance .............
PAGE 5
CD-S500 Series 3-7 Disassembly and Assembly of the Mechanism Unit ............................................................ 3-10 3-7-1 Disassembly and Assembly of Standard Model .................................................... 3-10 ♦ Removing the SA Rear Cover Switch and the Spring for Lever ........................ 3-10 ♦ Precaution when Mounting the Rear Cover Switch ........................................... 3-11 ♦ Removing the Mechanism Unit ..................................................
PAGE 6
CD-S500 Series ♦ Removing the Paper Guide ............................................................................... 3-28 ♦ Removing the Platen ......................................................................................... 3-28 ♦ Removing Armature Switch 2 ............................................................................ 3-29 ♦ Removing the SA1 PF shaft ..............................................................................
PAGE 7
CD-S500 Series 3-13 Oiling .................................................................................................................................... 3-42 3-14 Setting the Paper Near End Sensor .................................................................................... 3-43 3-15 Adjusting the Head Gap ....................................................................................................... 3-44 Chapter 4 4-1 4-2 PARTS LIST Mechanical Parts List .........................
PAGE 8
CD-S500 Series 5-3 SA, OPE-PANE PCB ........................................................................................................... 5-12 5-4 SA, SERIAL I/F PCB (MM) .................................................................................................. 5-13 5-5 SA, SERIAL I/F PCB (INCH) ............................................................................................... 5-14 5-6 SA, PARALLEL I/F PCB ...................................................................
PAGE 9
Chapter 1 SAFETY INSTRUCTIONS
PAGE 10
CD-S500 Series 1-1 Conventions for Warning and Caution The instructions that shall be observed to prevent injury to service personnel and others or damage to the user’s property are indicated with the following symbols. The symbols are classified for the degree of possible injury and damage due to incorrect use without following the instructions. Understand the meanings of these symbols before reading this manual.
PAGE 11
CD-S500 Series 1-4 CAUTION Precautions in Maintenance • When performing disassembly, assembly or adjustment, provide static protection and release static electricity from your body to protect printed circuit boards, etc. from damage due to static electricity. • When performing disassembly, assembly or adjustment, unplug the power cord of the printer from the service outlet to avoid shock hazards.
PAGE 12
Chapter 2 SPECIFICATIONS
PAGE 13
CD-S500 Series 2-1 General Specification Item Function 1. Printing mode Serial impact dot matrix 2. Printing direction Bi-directional 3. Head pins 9 pins (φ: 0.3mm, Pin interval: 1/72 inch) 4. Printing line columns Paper width of 76.2 mm: 40/42 or 33/35 columns Paper width of 69.5 mm: 36/40 or 30/32 columns Paper width of 57.5 mm: 30/33 or 25/27 columns Maximum printing region: 200/400 dots (full dot/including half dot) ANK 7 × 9 or 9 × 9 dots 5.
PAGE 14
CD-S500 Series Item Function Method: 11. Special ribbon cassette Colors: Single color (purple, black), 2-color (black and red) Life: Purple, approx. 4 million characters (continuous printing at 25°C) Ribbon Black, approx. 3 million characters (continuous printing at 25°C) Black/red, Black 1.5 million characters, Red 750,000 characters (continuous printing at 25°C) 12. Interface 13. Emulation 14.
PAGE 15
CD-S500 Series Item Function When packed: 22. Shock resistance 23. Electrostatic discharge threshold 24. Applicable standards When unpacked: height: 5 cm, Conforms to IEC 61000-4-2, direction: 1 corner, 3 edges, 6 faces direction: 4 edges, single side support contact discharge: 4 kV, air/indirect discharge: 8 kV UL60950-1, CSA C22.2 No.60950-1, FCC Class A, TÜV-GS (EN60950-1), CE Marking Class A, CCC (GB4943, GB9254, GB17625.1), VCCI Class A External Dimensions Standard model 132 156 247.
PAGE 16
Chapter 3 DISASSEMBLY, ASSEMBLY AND ADJUSTMENT
PAGE 17
CD-S500 Series 3-1 Precautions in Maintenance • When performing disassembly, assembly or adjustment, provide static protection and release static electricity from your body to protect printed circuit boards, etc. from damage due to static electricity. CAUTION • When performing disassembly, assembly or adjustment, unplug the power cord of the printer from the service outlet to avoid shock hazards. 3-2 Service Tools The following service tools are required for replacement of units, etc. in the field.
PAGE 18
CD-S500 Series 3-3 Disassembly Flow Diagram When replacing a part, refer to the disassembly flow diagram shown below. * “3-x” in the disassembly flow diagram shows the corresponding section number in this manual.
PAGE 19
CD-S500 Series 3-4 Disassembly and Assembly of AC Adapter Case (Built-in AC Adapter Type) The disassembly procedure is explained mainly. When assembling the parts, follow the disassembly procedure in reverse. ♦ Removing the AC Adapter 1) Remove screws A (2 pcs.) and screws B (2 pcs.), and remove the AC adapter case from the chassis. 2) Remove screws C (4 pcs.), and remove the hanger support from the AC adapter case. 3) Remove the AC adapter from the AC adapter case.
PAGE 20
CD-S500 Series 3-5 Disassembly and Assembly of the Rear Cover, Window and Rear Plate 3-5-1 Disassembly and Assembly of Standard Model The disassembly procedure is explained mainly. When assembling the parts, follow the disassembly procedure in reverse. ♦ Removing Rear Cover N and Window N 1) Slide the knob in the direction of the arrow and open rear cover N. 2) Remove screws A (2 pcs.), and remove rear cover N from the platen chassis.
PAGE 21
CD-S500 Series ♦ Removing the Rear Plate 1) Remove the rear plate from case U. * Unhook the claw at the rear plate from the catch on case U and pull the rear plate upwards. Rear plate Claw Catch Case U * The above figure shows a standard model.
PAGE 22
CD-S500 Series 3-5-2 Disassembly and Assembly of Rewinder Model The disassembly procedure is explained mainly. When assembling the parts, follow the disassembly procedure in reverse. ♦ Removing Rear Cover R and Window R 1) Slide knob R in the direction of the arrow and open rear cover R. 2) Remove screws A (2 pcs.), and remove rear cover R from the cutter chassis. * Push the claws at rear cover R outwards when removing rear cover R. 3) Remove window R from rear cover R.
PAGE 23
CD-S500 Series 3-6 Disassembly and Assembly of Case U, Front Cover and Operation Panel PCB The disassembly procedure is explained mainly. When assembling the parts, follow the disassembly procedure in reverse. ♦ Removing the Lever Cover, Case U and Knob N 1) In the case of rewinder model, remove the lever cover. * Pull the lever cover strongly to remove it. 2) Remove screws A (6 pcs.) on the bottom, and remove case U from the body chassis.
PAGE 24
CD-S500 Series ♦ Precaution when Mounting Case N • ♦ When case U has been mounted, check that the power switch is turned off. Removing the Front Cover 1) Remove screws A (2 pcs.), and remove the front cover from case U. ♦ Removing the Operation Panel PCB 1) Remove screws B (3 pcs.), and remove the operation panel plate from case U. 2) Remove screws C (2 pcs.), and remove the operation panel PCB from the operation panel plate.
PAGE 25
CD-S500 Series ♦ Removing the Rewinder Case (For Rewinder Model Only) 1) Remove screws A (4 pcs.) and screws B (2 pcs.), and remove the rewinder case from the base frame. * Pull the sides of the rewinder case outwards to disengage the bosses for positioning when removing the rewinder case. Paper holder 3 Hook Base frame Rewinder case Screw B Binding head screw M3 × 8 (P TITE) Bosses Screw A Binding head screw M3 × 5 Slot GND sheet Holes for bosses * The above figure shows a rewinder model.
PAGE 26
CD-S500 Series 3-7 Disassembly and Assembly of the Mechanism Unit 3-7-1 Disassembly and Assembly of Standard Model The disassembly procedure is explained mainly. When assembling the parts, follow the disassembly procedure in reverse. ♦ Removing the SA Rear Cover Switch and the Spring for Lever 1) Remove screw A (1 pc.), and remove the switch unit of the SA rear cover switch from the mechanism unit.
PAGE 27
CD-S500 Series ♦ Precaution when Mounting the Rear Cover Switch • When mounting the rear cover switch on the mechanism unit, fit the boss into the corresponding hole for positioning. • Secure the rear cover switch with adhesive tape. Hole for boss Boss Rear cover switch Adhesive tape Mechanism unit * The above figure shows a standard model.
PAGE 28
CD-S500 Series ♦ Removing the Mechanism Unit 1) Remove screws A (2 pcs.) and screws B (4 pcs.), and remove the mechanism unit from the base frame. * Use the positioning release slots (4 positions) and disengage the mechanism unit when removing the mechanism unit. * If the black mark sensor (optional) is provided, it is necessary to disconnect the cable connector of the black mark sensor from the main PCB.
PAGE 29
CD-S500 Series ♦ Precaution when Mounting the Mechanism Unit • When mounting the mechanism unit on the base frame, fit the bosses into the corresponding holes for positioning. When positioning has been completed, attach the springs for the levers, close the platen chassis and tighten screws A and screws B. * With the rewinder model, close the platen chassis and the cutter chassis and tighten screws A and screws B in order. • When the mechanism unit has been mounted, be sure to adjust the head gap.
PAGE 30
CD-S500 Series 3-7-2 Disassembly and Assembly of Rewinder Model * The disassembly and assembly procedures of the mechanism unit for the rewinder model are the same as those for the standard model. If the platen chassis is not opened, operate lever R in the direction of the arrow to keep the platen chassis open during the work. Refer to “3-7-1 Disassembly and Assembly of Standard Model” (Page 3-10). Platen chassis Lever R * The above figure shows a rewinder model.
PAGE 31
CD-S500 Series 3-8 Disassembly and Assembly of the Main PCB Unit The disassembly procedure is explained mainly. When assembling the parts, follow the disassembly procedure in reverse. ♦ Removing the PCB Cover 1) Remove the catches (4 positions in total on the right and left) from the PCB cover using a pair of tweezers, and remove the PCB cover from the base frame. PCB cover Base frame Main PCB * Catch (4 positions in total on the right and left) The above figure shows a standard model.
PAGE 32
CD-S500 Series ♦ Precaution when Mounting the PCB Cover • When mounting the PCB cover on the base frame, fit the catches (4 positions in total on the right and left) of the PCB cover to the claws on the base frame. • Fit the hook on the PCB cover in the space between paper holder 1 and the base frame. Paper holder 1 Hook PCB cover Base frame Claw PCB cover * The above figure shows a standard model.
PAGE 33
CD-S500 Series ♦ Removing the SA I/F PCB * The SA I/F PCB can be removed from the printer fully assembled. * There are several types of SA I/F PCB depending on the interface specification. In this section, the removing and mounting procedures for the SA parallel I/F PCB are explained; the procedures are the same for other types of SA I/F PCB. 1) Remove screws A (2 pcs.), and remove I/F PCB from the base frame.
PAGE 34
CD-S500 Series ♦ Removing the Cables 1) Remove all the cables from the connectors on the main PCB. * The following cables are connected on the main PCB.
PAGE 35
CD-S500 Series ♦ Removing the SA Front Cover Switch 1) Remove screw A (1 pc.), and remove the SA front cover switch from the base frame. ♦ Removing the Main PCB 1) Remove screws B (4 pcs.), and remove the main PCB from the base frame. Screw B Binding head screw M3 × 5 Power switch Main PCB Slot SA front cover switch Base frame Screw A Screw M1.7 × 6 (#0) Boss * Hole for boss The above figure shows a standard model.
PAGE 36
CD-S500 Series 3-9 Disassembly and Assembly of the Printing Unit The disassembly procedure is explained mainly. When assembling the parts, follow the disassembly procedure in reverse. * ♦ The manual cutter, lower blade, head cover, SA print head, and ribbon mask can be removed from the printer fully assembled. Removing the Manual Cutter 1) Remove screws A (2 pcs.), and remove the manual cutter from the cutter plate. ♦ Removing the Lower Blade (Optional) 1) Remove screw B (1 pc.
PAGE 37
CD-S500 Series ♦ Precaution when Mounting the Lower Blade (Optional) • When mounting the lower blade on the cutter plate, keep the orientation confirmation hole on the lower blade on the side of lever R and the chamfered corner of the lower blade on the auto cutter side. • When mounting the lower blade on the cutter plate, fit the boss into the corresponding hole for positioning.
PAGE 38
CD-S500 Series ♦ Removing the Head Cover 1) Remove screws A (2 pcs.), and remove the head cover from the main frame. * ♦ Unhook the projections (2 positions) of the head cover when removing the head cover. Removing the SA Print Head 1) Remove screws B (2 pcs.), and remove the SA print head from the carriage. * ♦ Remove the print head FPC from the connector. Removing the Ribbon Mask 1) Remove screw C (1 pc.), and remove the ribbon mask from the carriage. Screw C Screw M1.
PAGE 39
CD-S500 Series ♦ Precaution when Mounting the SA Print Head and the Ribbon Mask • When mounting the SA print head on the carriage, fit the boss into the corresponding hole for positioning. • Set the print head FPC while fitting into the groove on the carriage, and insert the print head FPC into the connector. Use some tools and the insert-assisting holes (2 positions) when the print head FPC.
PAGE 40
CD-S500 Series ♦ Removing the SA Black Mark Sensor PCB 1) Remove screws A (2 pcs.), and remove the PF motor from the main frame. 2) Remove screw B (1 pc.), and remove the SA black mark sensor PCB from the main frame. * The mounting position of the SA black mark sensor varies depending on the specification. Screw B Binding head screw M2 × 4 Notch SA black mark sensor PCB PF motor Main frame Screw A Screw M2 × 2.
PAGE 41
CD-S500 Series ♦ Oiling to the Printing Unit When maintenance of the printing unit has been performed, supply an adequate amount of oil to the positions shown in the figure below. Use the type of oil specified in the figure. For the oil type, refer to “3-13 Oiling” (Page 3-42).
PAGE 42
CD-S500 Series 3-10 Disassembly and Assembly of the Platen Chassis and Cutter Chassis 3-10-1 Disassembly and Assembly of Standard Model The disassembly procedure is explained mainly. When assembling the parts, follow the disassembly procedure in reverse. ♦ Removing the Sector Gear Plates 1 and 2 1) Remove screws A (1 pc. each), and remove sector gear plate 1 and sector gear plate 2 from the platen chassis. ♦ Removing the Platen Chassis 1) Remove E rings (2 pcs.), washer A (1 pc.), washers B (3 pcs.
PAGE 43
CD-S500 Series ♦ Precaution when Mounting Sector Gear Plates 1, 2 • When mounting sector gear plates 1 and 2 on the platen chassis, fit the bosses on the sector gear plates 1 and 2 into the corresponding holes on the platen chassis. • When mounting sector gear plates 1 and 2 on the platen chassis, supply oil to these parts. Refer to “3-10-1 Disassembly and Assembly of Standard Model” and “♦ Oiling to the Platen Chassis” (Page 3-30).
PAGE 44
CD-S500 Series ♦ Removing the Platen Cover 1) Remove screws A (2 pcs.), and remove the platen cover from the platen. • When removing the platen cover, be careful not to strain the paper guide. Otherwise, the paper guide fixing area may be damaged. CAUTION ♦ Removing the Paper Guide 1) Remove screws B (2 pcs.), and remove the paper guide from the platen cover. ♦ Removing the Platen 1) Remove screws C (2 pcs.), and remove the platen from the platen chassis.
PAGE 45
CD-S500 Series ♦ Removing Armature Switch 2 1) Remove screw A (1 pc.), and remove armature switch 2 from the platen chassis. ♦ Removing the SA1 PF shaft 1) Remove the E ring (1 pc.), and remove the SA1 PF shaft from the platen chassis. * Slide the bearing and the SA1 PF shaft in the direction of the arrow when removing the SA1 PF shaft. Armature switch 2 Bosses E ring (3.
PAGE 46
CD-S500 Series ♦ Oiling to the Platen Chassis When maintenance of the platen chassis has been performed, supply an adequate amount of oil to the positions shown in the figure below. Use the type of oil specified in the figure. For the oil type, refer to “3-13 Oiling” (Page 3-42).
PAGE 47
CD-S500 Series 3-10-2 Disassembly and Assembly of Rewinder Model The disassembly procedure is explained mainly. When assembling the parts, follow the disassembly procedure in reverse. ♦ Removing the Cutter Chassis 1) Remove the E rings (2 pcs.), and remove the cutter chassis from the base frame. * Pull the bottom (where the mounting holes are located) of the cutter chassis outwards when removing the cutter chassis. ♦ Removing the Sector Gear Plate 1 1) Remove screw A (1 pc.
PAGE 48
CD-S500 Series ♦ Precaution when Mounting the Sector Gear Plate 1 • When mounting sector gear plate 1 on the platen chassis, fit the bosses on sector gear plate 1 into the corresponding holes on the platen chassis. • When mounting sector gear plate 1 on the platen chassis, supply oil to these parts. Refer to “3-10-2 Disassembly and Assembly of Rewinder Model” and “♦ Oiling to the Platen Chassis and the Cutter Chassis” (Page 3-34).
PAGE 49
CD-S500 Series ♦ Removing the Platen Cover 1) Remove screws A (binding head screw M2 × 4: 2 pcs.), and remove the platen cover from the platen. * The removing procedure of the platen cover is the same as is the case with the standard model. Refer to “3-10-1 Disassembly and Assembly of Standard Model” and “♦ Removing the Platen Cover” (Page 3-28). • When removing the platen cover, be careful not to strain the paper guide. Otherwise, the paper guide fixing area may be damaged.
PAGE 50
CD-S500 Series ♦ Oiling to the Platen Chassis and the Cutter Chassis When maintenance of the platen chassis or the cutter chassis has been performed, supply an adequate amount of oil to the positions shown in the figure below. Use the type of oil specified in the figure. For the oil type, refer to “3-13 Oiling” (Page 3-42).
PAGE 51
CD-S500 Series 3-11 Disassembly and Assembly of the Auto Cutter 3-11-1 Disassembly and Assembly of Standard Model The disassembly procedure is explained mainly. When assembling the parts, follow the disassembly procedure in reverse. ♦ Removing the Auto Cutter (Optional) 1) Remove screws A (2 pcs.), and remove the auto cutter from the auto cutter plate. * Use the positioning release slots (2 positions) and disengage the auto cutter when removing the auto cutter.
PAGE 52
CD-S500 Series ♦ ♦ Precaution when Mounting the Auto Cutter (Optional) • When mounting the auto cutter on the auto cutter plate, fit the bosses into the corresponding holes for positioning. • Route the auto cutter cable as shown in the figure and tie down the cable with the cable tie. Precaution when Mounting the Auto Cutter Plate • When mounting the auto cutter plate on the platen chassis, fit the bosses into the corresponding holes for positioning.
PAGE 53
CD-S500 Series 3-11-2 Disassembly and Assembly of Rewinder Model The disassembly procedure is explained mainly. When assembling the parts, follow the disassembly procedure in reverse. ♦ Removing the Auto Cutter 1) Remove screws A (2 pcs.), and remove the auto cutter from the cutter chassis. * Use the positioning release slots (2 positions) and disengage the auto cutter when removing the auto cutter. * ♦ Cut the cable tie of the auto cutter cables and remove the auto cutter.
PAGE 54
CD-S500 Series ♦ ♦ Precaution when Mounting the Auto Cutter • When mounting the auto cutter on the cutter chassis, fit the bosses into the corresponding holes for positioning. • Route the auto cutter cable as shown in the figure and tie down the cable with the cable tie. Precaution when Mounting Armature Switch 1 • When mounting armature switch 1 on the cutter chassis, check the orientation as shown in the figure and fit the bosses into the corresponding holes for positioning.
PAGE 55
CD-S500 Series 3-12 Disassembly and Assembly of the Rewinder Unit (For rewinder model only) The disassembly procedure is explained mainly. When assembling the parts, follow the disassembly procedure in reverse. ♦ Removing the Rewinder Motor 1) Remove screws A (2 pcs.), and remove the rewinder motor from the rewinder motor frame. ♦ Removing the Rewinder Gear, Rewinder Roller and Rewinder Roller Pin 1) Remove the rewinder gear, rewinder roller and rewinder roller pin from the rewinder motor frame.
PAGE 56
CD-S500 Series ♦ ♦ Precaution when Mounting the Rewinder Motor • Attach the rewinder motor in an angle so that the cable connecting section will be hidden. • When the rewinder motor has been mounted on the rewinder motor frame, route the rewinder motor cable as shown in the figure and secure it with adhesive tape. Precaution when Mounting the Rewinder Roller Pin • When mounting the rewinder roller pin on the rewinder motor frame, supply oil to these parts.
PAGE 57
CD-S500 Series ♦ Oiling to the Rewinder Unit When maintenance of the rewinder unit has been performed, supply an adequate amount of oil to the positions shown in the figure below. Use the type of oil specified in the figure. For the oil type, refer to “3-13 Oiling” (Page 3-42). Rewinder roller pin outer surface (Oil type: MG-1) * The above figure shows a rewinder model.
PAGE 58
CD-S500 Series 3-13 Oiling Oiling Period The printer is free from maintenance and oiling is not required for normal use. When the printer has been disassembled, assembled or cleaned or when a part has been replaced, supply oil to the related parts. Oil Table Name FLOIL grease Lubricant Precision machine grease Type Manufacturer MG-1 Kanto Chemical Co., Ltd. MOBIL1 ExxonMobil Yugen Kaisha SUMITEC 305 Sumico Lubricant Co., Ltd.
PAGE 59
CD-S500 Series 3-14 Setting the Paper Near End Sensor Change the sensor position according to the printer installation and the inner diameter of the roll paper. Refer to the following table, hold down the concave part in the center of the sensor with your finger and move it right or left to the position suitable for the working condition. (When shipped from the factory, it is set at φ24 mm.) Installation Method Remaining Roll Paper (mm) Sensor Location Approx. φ22 1 Approx. φ24 2 Approx.
PAGE 60
CD-S500 Series 3-15 Adjusting the Head Gap When the following parts have been removed or when the fixing screws of these parts are loosened, be sure to adjust the head gap. • Mechanism unit • Platen Head Gap Adjusting Procedure 1) Remove case U. Refer to “3-6 Disassembly and Assembly of Case U, Front Cover and Operation Panel PCB” and “♦ Removing the Lever Cover, Case U and Knob N” (Page 3-7). 2) Close the platen chassis.
PAGE 61
Chapter 4 PARTS LIST
PAGE 62
CD-S500 Series 4-1 Mechanical Parts List 4-1-1 Drawing No. 1 Parts List & Location for AC Adapter Case CD-S500 Series Drawing No. 1 Parts List & Location for AC Adapter Case Revisions List Sheet No. Rev. No. Date 1/1 1 2004. 11. 1 1/1 2 2005. 5.
PAGE 63
CD-S500 Series Drawing No.
PAGE 64
CD-S500 Series Parts List for CD-S500 Series: TITLE: AC Adapter Case Drawing No. 1 Sheet No. 1/1 Rev. No. 2 Q’ty/Unit Location Part No. 1-1 NJ59701-0 SA, AC ADAPTER CASE W 1 White case Including 1-2, 1-8 NJ59702-0 SA, AC ADAPTER CASE B 1 Black case Including 1-2, 1-8 1-2 NJ56211-0 CASE, AC ADAPTER W 1 White case CASE, AC ADAPTER B 1 Black case 1-3 E11130-080F SCREW, PHT (ST), M3.0X8 2 1-4 E10130-140F SCREW, PHT (PT), M3.
PAGE 65
CD-S500 Series 4-1-2 Drawing No. 2 Parts List & Location for Rear Cover CD-S500 Series Drawing No. 2 Parts List & Location for Rear Cover Revisions List Sheet No. Rev. No. Date 1/1 1 2004. 11. 1 1/1 2 2005. 5.
PAGE 66
CD-S500 Series Drawing No.
PAGE 67
CD-S500 Series Parts List for CD-S500 Series: TITLE: Rear Cover Drawing No. 2 Sheet No. 1/1 Rev. No. 2 Q'ty/Unit Location Part No. 2-1 NJ56203-0 COVER, REAR R W 1 White case NJ56214-0 COVER, REAR R B 1 Black case 2-2 Part Name CD-S500, 501 CD-S503 Remark NJ56204-0 COVER, REAR N W 1 White case NJ56215-0 COVER, REAR N B 1 Black case SCREW M3.
PAGE 68
CD-S500 Series 4-1-3 Drawing No. 3 Parts List & Location for Overall Cover CD-S500 Series Drawing No. 3 Parts List & Location for Overall Cover Revisions List Sheet No. Rev. No. Date 1/1 1 2004. 11. 1 1/1 2 2005. 5.
PAGE 69
CD-S500 Series Drawing No.
PAGE 70
CD-S500 Series CD-S500 (Standard model) CD-S501 (Built-in autocutter model) CD-S503 (Rewinder model) 9 7 10 8 4-9
PAGE 71
CD-S500 Series Parts List for CD-S500 Series: TITLE: Overall Cover Drawing No. 3 Location Part No. 3-1 NJ56201-0 NJ56212-0 3-2 E12830-080DF 3-3 NJ56701-0 3-4 E00930-050F NJ56702-0 CD-S503 CASE U W 1 1 White case CASE U B 1 1 Black case SCREW M3.0X8 P TITE BIND 6 6 SA, COVER, FRONT W 1 1 White case SA, COVER, FRONT B 1 1 Black case SCREW PH (SW+PW) M3.
PAGE 72
CD-S500 Series 4-1-4 Drawing No. 4 Parts List & Location for Mechanism Unit CD-S500 Series Drawing No. 4 Parts List & Location for Mechanism Unit Revisions List Sheet No. Rev. No. Date 1/1 1 2004. 11. 1 1/1 2 2005. 5.
PAGE 73
CD-S500 Series Drawing No. 4 Mechanism Unit CD-S500 (Standard model) CD-S501 (Built-in autocutter model) CD-S503 (Rewinder model) 5 4 6 3 4 (a) 2 3 2 (b) 8 * 7 Refer to Page 4-17 for connections of connectors (a) and (b).
PAGE 74
CD-S500 Series CD-S500 (Standard model) CD-S501 (Built-in autocutter model) CD-S503 (Rewinder model) 12 14 11 13 34 10 25 9 15 10 24 33 17 21 19 20 18 1 16 22 23 4-13
PAGE 75
CD-S500 Series CD-S500 (Standard model) CD-S501 (Built-in autocutter model) CD-S503 (Rewinder model) 28 32 31 29 30 (c) 27 26 * Refer to Page 4-17 for connections of connector (c).
PAGE 76
CD-S500 Series Parts List for CD-S500 Series: TITLE: Mechanism Unit Drawing No. 4 Location Part No. Sheet No. 1/1 Rev. No. 2 Q'ty/Unit Part Name CD-S500 CD-S501 CD-S503 4-1 NJ19801-0 UNIT, MECHANISM 1 1 1 4-2 E00530-050F SCREW M3.0X5 BIND 4 4 4 4-3 E00540-060F SCREW M4.0X6 BIND 2 2 2 4-4 NJ43604-0 SPRING, LEVER 2 2 2 4-5 NJ68705-0 SA, REAR COVER SW 1 1 1 4-6 E00520-075F SCREW M2.0X7.5 BIND 1 1 1 SA, FRONT COVER SW 1 1 1 SCREW M1.
PAGE 77
CD-S500 Series 4-1-5 Drawing No. 5 Parts List & Location for Main PCB CD-S500 Series Drawing No. 5 Parts List & Location for Main PCB Revisions List Sheet No. Rev. No. Date 1/1 1 2004. 11. 1 1/1 2 2005. 5.
PAGE 78
CD-S500 Series Drawing No.
PAGE 79
CD-S500 Series CD-S500 (Standard model) CD-S501 (Built-in autocutter model) CD-S503 (Rewinder model) 8 6 7 4-18
PAGE 80
CD-S500 Series Parts List for CD-S500 Series: TITLE: Main PCB Drawing No. 5 Sheet No. 1/1 Rev. No. 2 Q'ty/Unit Location Part No. 5-1 NJ66820-0 UNIT, MAIN PCB (WITH ROM) NJ66810-0 UNIT, MAIN PCB AC (WITH ROM) NJ66800-0 UNIT, MAIN PCB AC+RW (WITH ROM) NJ66834-0 UNIT, MAIN PCB CHN (WITH ROM) NJ66832-0 UNIT, MAIN PCB AC CHN (WITH ROM) NJ66830-0 UNIT, MAIN PCB A+R CH (WITH ROM) 5-2 * * * E00530-050F Part Name CD-S500 SCREW M3.
PAGE 81
CD-S500 Series 4-1-6 Drawing No. 6 Parts List & Location for Base Frame CD-S500 Series Drawing No. 6 Parts List & Location for Base Frame Revisions List Sheet No. Rev. No. Date 1/1 1 2004. 11. 1 1/2 2 2005. 5. 20 2/2 2 2005. 5.
PAGE 82
CD-S500 Series Drawing No.
PAGE 83
CD-S500 Series CD-S500 (Standard model) 16 47 20 47 45 19 40 38 20 39 29 25 24 24 30 25 4-22
PAGE 84
CD-S500 Series CD-S501 (Built-in autocutter model) 26 25 21 31 35 25 32 34 33 34 22 35 1 3 4 10 5 6 4 7 14 15 10 8 9 11 4-23
PAGE 85
CD-S500 Series CD-S501 (Built-in autocutter model) 27 17 46 (e) 18 20 41 18 45 19 40 38 20 * Refer to Page 4-17 for connections of connector (e).
PAGE 86
CD-S500 Series CD-S503 (Rewinder model) 37 33 21 25 A 35 33 35 36 A 2 3 4 10 5 4 6 7 10 8 9 11 4-25
PAGE 87
CD-S500 Series CD-S503 (Rewinder model) 27 17 46 (e) 13 12 45 18 44 42 18 43 * Refer to Page 4-17 for connections of connector (e).
PAGE 88
CD-S500 Series Parts List for CD-S500 Series: TITLE: Base Frame Drawing No. 6 Sheet No. 1/2 Rev. No. 2 Location Part No. 6-1 NJ49801-0 UNIT, BASE FRAME STD 6-2 NJ49802-0 UNIT, BASE FRAME RWD * * * 6-3 NJ24702-1 6-4 E00930-060F 6-5 NJ28201-0 6-6 E00520-040F 6-7 NJ24207-0 6-8 E13717-060F 6-9 NJ22702-0 6-10 E60330-000F 1 1 1 1 2 2 2 COVER, PLATEN 1 1 1 SCREW M2.0X4 BIND 2 2 2 GUIDE, PAPER 1 1 1 SCREW, M1.7X6.
PAGE 89
CD-S500 Series Parts List for CD-S500 Series: TITLE: Base Frame Drawing No. 6 Location Part No. 6-40 E60330-000F 6-41 NJ24703-0 * * * Sheet No. 2/2 Rev. No. 2 Q'ty/Unit Part Name E-RING, 3 CD-S500 CD-S501 2 2 CD-S503 2 SA, CHASSIS PLATEN CAP 2 6-42 NJ44106-0 CHASSIS, CUTTER 1 6-43 NJ42002-0 SHAFT, CHASSIS CUTTER 1 6-44 E60320-000F 6-45 NJ90908-0 LABEL, CATCHING CAUTION 6-46 NJ90907-0 LABEL, AUTO CUTTER CAUTION 6-47 E12830-080DF E-RING, 2 2 SCREW, M3.
PAGE 90
CD-S500 Series 4-1-7 Drawing No. 7 Parts List & Location for Rewinder CD-S500 Series Drawing No. 7 Parts List & Location for Rewinder Revisions List Sheet No. Rev. No. Date 1/1 1 2004. 11. 1 1/1 2 2005. 5.
PAGE 91
CD-S500 Series Drawing No.
PAGE 92
CD-S500 Series CD-S503 (Rewinder model) 15 11 9 (d) 12 10 8 10 * Refer to Page 4-17 for connections of connector (d).
PAGE 93
CD-S500 Series Parts List for CD-S500 Series: TITLE: Rewinder Drawing No. 7 Sheet No. 1/1 Rev. No. 2 Q'ty/Unit Location Part No. 7-1 NJ58201-0 CASE, REWINDER W 1 White case NJ58202-0 CASE, REWINDER B 1 Black case * * * 7-2 E12830-080DF 7-3 E00530-050F 7-4 7-5 Part Name CD-S500, 501 CD-S503 SCREW, M3.0X8 P TITE BIND 2 SCREW M3.
PAGE 94
CD-S500 Series 4-1-8 Drawing No. 8 Parts List & Location for Paper Near End Sensor CD-S500 Series Drawing No. 8 Parts List & Location for Paper Near End Sensor Revisions List Sheet No. Rev. No. Date 1/1 1 2004. 11. 1 1/1 2 2005. 5.
PAGE 95
CD-S500 Series Drawing No. 8 Paper Near End Sensor CD-S500 (Standard model) CD-S501 (Built-in autocutter model) CD-S503 (Rewinder model) (f) 3 4 1 2 * Refer to Page 4-17 for connections of connector (f).
PAGE 96
CD-S500 Series Parts List for CD-S500 Series: TITLE: Paper Near End Sensor Drawing No. 8 Location Part No. 8-1 NJ14203-0 8-2 E13717-040WF Sheet No. 1/1 Rev. No. 2 Q'ty/Unit Part Name CD-S500, 501 CD-S503 HOLDER, NE SENSOR A 1 1 SCREW, M1.7X4.
PAGE 97
CD-S500 Series 4-2 Electric Parts List 4-2-1 Parts List & Location for Unit, Main PCB Parts List & Location for Unit, Main PCB AC + RW (WITH ROM) Revision Up List Sheet No. Rev. No. Date 1/5 1 2004. 12. 1 2/5 1 2004. 12. 1 3/5 1 2004. 12. 1 4/5 1 2004. 12. 1 5/5 1 2004. 12. 1 1/5 2 2005. 5. 20 2/5 2 2005. 5. 20 3/5 2 2005. 5. 20 4/5 2 2005. 5. 20 5/5 2 2005. 5.
PAGE 98
CD-S500 Series Surface Mounting Drawing: Main PCB Mounted Surface 4-37
PAGE 99
CD-S500 Series Soldered Surface 4-38
PAGE 100
4-39 C2620-011# C2900-143# C2319-036# C2560-602# C2701-102# C2256-061# C2256-072# C2256-051# C2256-073# C2256-048# C2256-049# C2800-132# 7 8 9 10 11 12 13 14 15 16 17 18 C6149-167# C2400-033# 6 21 NJ66900-**F 5 C2703-428# NJ66700-**F 4 C6198-727# C2308-071# 3 20 NJ94700-**F 19 NJ66800-**F 2 Part No. 1 Item No.
PAGE 101
C5270-427# C5270-428# C5270-429# C5270-430# C5270-353# C5270-326# C5270-431# 37 38 39 40 41 C5270-354# 31 36 C6202-103# 30 35 C6198-404# 29 C5270-447# C6180-093# 28 C5270-426# C6202-704# 27 34 C6202-603# 26 33 C6205-002# 25 C5270-351# C6202-102# 24 32 C6149-168# C6198-608# 23 Part No. 22 Item No.
PAGE 102
C7511-053# C7511-168# C4927-000# C4929-000# C4927-101# C4927-621# 56 57 58 59 60 51 C7302-399# C3610-079# 50 55 C3610-071# 49 54 C3610-078# 48 C7302-402# C3600-134# 47 C7302-414# C3600-118# 46 53 C5190-706# 45 52 C5190-710# C5190-705# 44 C5270-432# C5190-709# 43 Part No. 42 Item No.
PAGE 103
4-42 C4923-005# C4927-103# C4927-563# C4927-434# C4927-204# C4927-102# 63 64 65 66 67 68 C4927-104# C4937-110# C4937-123# C4937-102# C4600-083# C3905-071# C3905-072# C7650-007# 73 74 75 76 77 78 79 71 72 C4937-120# C4928-271# 70 C4927-303# C4927-105# 62 69 C4927-223# Part No. 61 Item No. Part Name SW, 10A_250V_AC_QUALIFIED_ POWER_SWITCH DTR, DG_TRANSSITOR DTR, DG_TRANSSITOR TH, CHIP_THERMISTOR, 10KOHM, 1%, 1005 R, CHIP_RES, 10KOHM, 1%, 1005 R, CHIP_RES, 4.
PAGE 104
C3551-004# C3903-098# C3903-108# C3402-195# C3201-351# C7800-062# E01030-080F C3402-143# C7400-003# C3750-168# C3750-166# C7900-114# 81 82 83 84 85 86 87 88 89 90 91 Part No. 80 Item No. Part Name BZ, BUZZER ZD, ZENNER_DIODE, ZD, ZENNER_DIODE, Y, CERAMIC_RESONATOR, 20MHZ TR, MEDIUM_DRIVE_TRANSISTOR, SC-63 SCREW HEAT_SINK TR, DARLINGTON_TRANSISTOR, DIP, 3PIN TR, POWER_TRANSISTOR, 100V, 2A, 3PIN TR, P-CH_MOSFET, ID=3A, 3PIN SMA4032 DBX05ALF-P050N UDZSFTE-176.
PAGE 105
CD-S500 Series 4-2-2 Parts List & Location for Unit, Ope-Pane PCB Parts List & Location for Unit, Ope-Pane PCB Revisions List Sheet No. Rev. No. Date 1/1 1 2004. 12.
PAGE 106
CD-S500 Series Surface Mounting Drawing: Ope-Pane PCB Mounted Surface Soldered Surface 4-45
PAGE 107
C3803-092 4 6 5 C6198-608 3 C7640-047 (C3803-095) C3803-083 (C3803-089) NJ66910-** 2 Part No. NJ66730-** 1 Item No.
PAGE 108
CD-S500 Series 4-2-3 Parts List & Location for Unit, Serial I/F PCB Parts List & Location for Unit, Serial I/F (MM) PCB Revisions List Sheet No. Rev. No. Date 1/1 1 2004. 12.
PAGE 109
CD-S500 Series Surface Mounting Drawing: Serial I/F PCB Mounted Surface 4-48
PAGE 110
FB, CHIP_BEAD_ARRAY, 120OHM, 3216 BLA31BD121SN4D PLATE, I/F SERIAL C7539-044 NJ64102-00 E8488-310 9 10 LABEL (MM) GRM188F11H104ZA01D UVZ1E101MED 205A-25FGNBBC3 DHB-RA30-R131N-FA 8 C, CHIP_CAP, 0.1UF, F, Z, 50V, 1608 EC, AL_ELEC_CAP, 100UF, 25V CN, RS232_I/F, 25PIN, M2.
PAGE 111
CD-S500 Series Parts List & Location for Unit, Serial I/F (INCH) PCB Revisions List Sheet No. Rev. No. Date 1/1 1 2004. 12.
PAGE 112
FB, CHIP_BEAD_ARRAY, 120OHM, 3216 BLA31BD121SN4D PLATE, I/F SERIAL C7539-044 NJ64102-00 E8488-320 9 10 LABEL (INCH) GRM188F11H104ZA01D UVZ1E101MED 205A-25FGNBBB3 DHB-RA30-R131N-FA 8 C, CHIP_CAP, 0.
PAGE 113
CD-S500 Series 4-2-4 Parts List & Location for Unit, Parallel I/F PCB Parts List & Location for Unit, Parallel I/F PCB Revisions List Sheet No. Rev. No. Date 1/1 1 2004. 12.
PAGE 114
CD-S500 Series Surface Mounting Drawing: Parallel I/F PCB Mounted Surface Soldered Surface 4-53
PAGE 115
C6149-170 C6149-166 8 9 4-54 C4498-015 C4498-016 NJ64101-00 21 22 19 20 C4928-473 C4498-014 18 C4928-101 15 C4928-103 C7539-044 14 17 C7539-045 13 16 C5270-452 C5270-453 12 C5270-451 C2256-079 7 C5190-711 C2256-078 6 11 C2256-077 5 10 C2256-076 4 IC, DUAL_FLIP_FLOP, TSSOP, 14PIN SN74AHC74PWR BLM21AG121SN1D GRM188B11H102KA01 GRM188B11H471KA01 GRM188B31H104KA92 UVZ1E101MED 57RE-40360-730B (D3)-FA DHB-RA30-R131N-FA SN74AHC05PWR SN74AHC14PWR SN74AHC00PWR PLATE,
PAGE 116
CD-S500 Series 4-2-5 Parts List & Location for Unit, PNE SENS PCB Parts List & Location for Unit, PNE SENS PCB Revisions List Sheet No. Rev. No. Date 1/1 1 2004. 12.
PAGE 117
CD-S500 Series Surface Mounting Drawing: PNE SENS PCB Mounted Surface Soldered Surface 4-56
PAGE 118
C4928-221# (C3801-055) C3801-054 3 4 NJ66916-** 2 Part No. NJ66766-** 1 Item No. Part Name R, CHIP_RES, 220OHM, 5%, 2012 PI, PHOTO_INTERRUPTER PWB (PNE SENS PCB) SA, PNE SENS PCB Parts List for CD-S500 Series: MCR10EZHEJ221 GP2S24B GP2S24B100F Type TITLE: PNE SENS PCB ROHM SHARP SHARP Manufacturer 2 2 1 1 Q’ty R201, 202 PI201, PI202 Location Sheet No. Rev. No.
PAGE 119
CD-S500 Series 4-2-6 Parts List & Location for Unit, BM SENS PCB Parts List & Location for Unit, BM SENS PCB Revisions List Sheet No. Rev. No. Date 1/1 1 2004. 12.
PAGE 120
CD-S500 Series Surface Mounting Drawing: BM SENS PCB Mounted Surface Soldered Surface 4-59
PAGE 121
C4920-221 (C3801-040) C3802-042 3 4 NJ66922-** 2 Part No. NJ66765-** 1 Item No. Part Name R, CHIP_RES, 220OHM, 5%, 3216 PI, PHOTO_INTERRUPTER PWB (BM SENSOR PCB) SA, BM SENS PCB Parts List for CD-S500 Series: MCR18EZHJ221 SG-105 TLP908-0 (LB) Type TITLE: BM SENS PCB ROHM KODENSHI TOSHIBA Manufacturer 1 1 1 1 Q’ty R301 PI301 Location Sheet No. Rev. No.
PAGE 122
CD-S500 Series 4-3 Accessory Parts List Accessory Parts List Revisions List Sheet No. Rev. No. Date 1/1 1 2005. 5.
PAGE 123
CD-S500 Series Parts List for CD-S500 Series: TITLE: Accessory Parts List Sheet No. 1/1 Rev. No. 1 Q'ty/Unit Location Part No.
PAGE 124
CD-S500 Series 4-4 Recommended Spare Parts List Recommended Spare Parts List Revisions List Sheet No. Rev. No. Date 1/1 1 2005. 5.
PAGE 125
CD-S500 Series Parts List for CD-S500 Series: TITLE: Recommended Spare Parts List Sheet No. 1/1 Rev. No. 1 Location Part No.
PAGE 126
Chapter 5 CIRCUIT DIAGRAMS
PAGE 127
5-1 DATE TITLE 2004.12.
PAGE 128
5-2 DATE 2004.12.
PAGE 129
5-3 DATE TITLE MODEL 2004.12.1 Revision UNIT, MAIN PCB AC+RW (WITH ROM) MEMORY CIRCUIT CD-S500 Series A 2/10 PAGE 5-2-2 JP20 not mounted but included in the pattern.
PAGE 130
5-4 DATE TITLE 2004.12.
PAGE 131
5-5 DATE TITLE 2004.12.
PAGE 132
5-6 DATE TITLE 2004.12.
PAGE 133
5-7 DATE TITLE 2004.12.
PAGE 134
5-8 DATE TITLE 2004.12.
PAGE 135
5-9 DATE TITLE 2004.12.
PAGE 136
5-10 DATE TITLE 2004.12.
PAGE 137
5-11 DATE TITLE 2004.12.
PAGE 138
5-12 DATE TITLE 2004.12.
PAGE 139
5-13 DATE TITLE 2004.12.
PAGE 140
5-14 DATE TITLE 2004.12.
PAGE 141
5-15 DATE TITLE MODEL 2004.12.
PAGE 142
5-16 DATE TITLE 2004.12.
PAGE 143
5-17 DATE TITLE 2004.12.
PAGE 144
Chapter 6 TROUBLESHOOTING
PAGE 145
CD-S500 Series 6-1 Troubleshooting List Symptom 1 Paper jam Check Action Check for a jam at the paper ejection opening. Remove all the jammed paper. Remove the roll paper from the printer and put it back again. If you cannot open the rear cover, make a check for 2. 2 Rear cover does not open Check to see if the blade of the auto cutter is protruding. Insert a Phillips screwdriver (+) into the cutter lock release feed hole on the printer and turn it clockwise or counter-clockwise.
PAGE 146
CD-S500 Series 9 Symptom Check Action Print is off the specified column position Check to see if fibers of paper or ink ribbon are collected on the HP sensor or partition plate. Remove fibers of paper or ink ribbon. Check to see if lubricant is present or dried up on the CR guide shaft and the carriage. Supply lubricant to the CR guide shaft and the carriage. Check to see if the ink ribbon is caught in the print head. If the ink ribbon is caught in the print head, replace the print head.
PAGE 147
CD-S500 Series Symptom 17 Rewinder does not rewind the paper correctly Check Action Check to see if the paper is set to the rewinder too loosely. If too loose, tense it. Note that the paper should be set tightly at the beginning of rewinding. Check to see if the rewinder roller is worn out. If worn out, replace the rewinder roller.
PAGE 148
CD-S500 Series 6-2 Clearing a Paper Jam Clearing Method 1) Turn off the power and open the rear cover. When there is a cutter problem, the printer may stop with the cutter blade protruding so that pressing the FEED switch fails to clear the error.
PAGE 149
CD-S500 Series 6-3 Operation Panel 6-3-1 Basic Display POWER PAPER ERROR OUT FEED LED POWER (Green): It is lit when the power is supplied and is off when the power is off. PAPER OUT (Orange): It is lit in paper-out status and is off when paper is loaded. (Hereinafter called “P.OUT”) ERROR (Orange): It is lit when the rear cover is open and is off when the cover is closed. Switch Status Paper Data When this switch is pressed once (less than 1 second), paper is fed by one line.
PAGE 150
CD-S500 Series 6-4 Error Indication Errors are indicated by a combination of POWER, P.OUT, and ERROR LEDs. (Each and represents 300 ms.) Type of Error LED Indication Operation and Restoration Method Printing stops and the printer goes offline. POWER (1) Paper end Replace the paper and close the cover to return the printer online. P.OUT ERROR (2) (3) Paper near end Rear/front cover open Paper end can be disabled by setting ESC c 4.
PAGE 151
CD-S500 Series Error Priority (1) < (2) < (3) < (4) < (5) < (6) < (7) < (8) < (9) < (10) Buzzer Sounding If the buzzer sounding is enabled by the soft switch: • In the error status described in “6-4 Error Indication”, if one of the (4) - (8) errors occurs, the buzzer continues to sound until the error is cancelled. • The buzzer sounds at the time of key operation in the software switch or the maintenance function (described later).
PAGE 152
CD-S500 Series 6-5 Demonstration Printing Function If FEED switch is held down while the printer is turned on with the front and rear covers closed, the demonstration printing mode is started. Then “demonstration patterns and the setting of the software switch” are printed. After completing the printing, the printer shifts to normal power-on status through POWER ON RESET operation. FROM VER. CQ01-XXXX FROM DATE -MM/DD YY Impact Dot Printer CD-S500 Feature: Print Speed: Approx. 5.
PAGE 153
CD-S500 Series 6-6 Maintenance Function If FEED switch is held down while the printer is turned on with the front cover opened and the rear cover closed, the maintenance mode is started. Status: Offline LED indication: POWER LED flashes at 0.3 second intervals( ERROR LEDs are off. ). P.OUT and In this status, close the front cover and select the function by pressing FEED switch the following number of times. Types of maintenance function (1) HEX dump mode Pressing FEED switch 0 times.
PAGE 154
CD-S500 Series 6-6-2 Soft SW Setting Mode If the front cover is reopened and then closed while POWER and P.OUT LEDs are flashing, the soft SW setting mode is started. POWER and P.OUT LEDs stop flashing and remain lit. Then the title and top items are printed. Operation Method Pressing FEED switch (less than 2 seconds): The setting is changed. The present set value is changed and the same item is reprinted. (Press FEED switch, and when the buzzer sounds once, release it.
PAGE 155
CD-S500 Series Press Feed → Change PARM. Title printing Press Feed For 2S → Next Item F.Cover Open/Close → Save & Exit - - - - - - - - - - - - - - - - Command Type -EPSON EPSON/STAR/CBM1/CBM2 Number of Col. -40/33 40/33, 42/35 Font Select -7 × 9 9×9/7×9 Paper Plies -OFF OFF/2P/3P Paper End -ENB ENB/DIS Paper Near-End -ENB ENB/DIS Slashed Zero -OFF OFF/ON Print Direct.
PAGE 156
CD-S500 Series Command Type The emulation is selected from EPSON/STAR/CBM1/CBM2. Initial value: EPSON Number of Col. The number of full dots in a full column is 200 dots. Initial value: 40/33 Number of Col.
PAGE 157
CD-S500 Series Slashed Zero It sets whether or not slash is used with the numeral 0 (ZERO). Initial value: OFF Print Direct. Designates the printing direction. When BIDIR is selected, printing starts from the left or right ends of the next printing line which is closer to the location where the previous print has stopped. When UNI-DIR is selected, printing always starts from the left end. Initial value: BI-DIR Auto LF The LF operation at the time of “CR” is selected. When it is OFF, only CR is operated.
PAGE 158
CD-S500 Series Baud Rate Initial value: 19200 Data Length Initial value: 8 bits Parity Bit Initial value: NONE Stop Bit Initial value: 1 bit Protocol These settings are for printers with the serial interface and displayed only when the serial board is mounted. The above 5 items of InterfaceSW are printed only with printers equipped with an RS232C I/F PC board. Initial value: DTR Paper Width Selects the paper size.
PAGE 159
CD-S500 Series Concerning MechanicalSW Operation Functions that are not supported by the specifications at time of shipping have no impact on printer operations even when the settings are changed. Example: Changes in the auto cutter setting for models that are not equipped with an auto cutter. Changes in the TakeUp Device setting for models that are not equipped with a rewinder. 6-6-3 Initial Factory Shipping Mode While POWER, P.
PAGE 160
CD-S500 Series 6-7 Maintenance Function for Service Under the condition that the front and rear covers are open, hold down FEED switch while turning on the printer to activate maintenance mode for service. Status: Offline LED indication: POWER LED flashes at 0.3 second intervals ( ERROR LEDs are off. ). P.OUT and In this state, load paper and close the front and rear covers. Then, select the function by pressing FEED switch the following number of times.
PAGE 161
CD-S500 Series 6-7-1 Busy Condition Check Mode If the front cover is opened and then closed while POWER LED is flashing, POWER LED stops flashing and remains lit. After printing from the busy condition to the PAPER WIDTH setting, the printer stands by for the next key operation. Operation Method Pressing FEED switch (less than 2 seconds): The setting is changed. The present set value is changed and the same item is reprinted. (Press FEED switch, and when the buzzer sounds once, release it.
PAGE 162
CD-S500 Series FROM VER. -DP01-0000 FROM DATE -MM.DD.YY BOOT DATE -MM.DD.YY BK MARK Air Temp. Head Temp. Head Temp. Head1 Head2 Head3 Head4 Head5 Head6 Head7 Head8 Head9 Feed Cutter XXXX XXXX XXXX XXXX -XXXXXXXXX -XXXXXXXXX -XXXXXXXXX -XXXXXXXXX -XXXXXXXXX -XXXXXXXXX -XXXXXXXXX -XXXXXXXXX -XXXXXXXXX -XXXXXXXXX -XXXXXXXXX FROM version printing Crt. Crt. Crt. Max.
PAGE 163
CD-S500 Series 6-7-2 ROM Rewrite Receiving Mode If the front cover is opened and then closed while POWER and P.OUT LEDs are flashing, both LEDs stop flashing and remain lit and the printer goes to the receive wait state. During data receiving, POWER LED is lit and P.OUT LED flashes. When the data receiving is completed, P.OUT LED stops flashing and remains lit. After ROM rewriting, only POWER switch is effective and no other function is accepted.
PAGE 164
CD-S500 Series 6-7-5 Drawer Check Mode If the front cover is opened and then closed while P.OUT LED is flashing, POWER and P.OUT LEDs stop flashing and remain lit and the printer goes to drawer check mode. Check Item and Operation Method Start POWER and P.