CITIZEN OPOS DRIVER 1.8 Setup Guide ’10/03/29 Rev 1.
CITIZEN OPOS DRIVER 1.8 Setup Guide Revision Record 2 Date Revision Description 07/12/21 Rev1.00 08/10/17 Rev1.01 08/12/12 Rev1.02 09/02/16 Rev1.03 09/05/07 Rev1.04 09/06/26 Rev1.05 New issue Installer was changed. (Also related issues were modified.) CT-S281 was newly supported. Unsupported column settings for CT-S200 were deleted. CT-S310 series were separated from CT-S300 series, and some settings for CT-S310 were added.
CITIZEN OPOS DRIVER 1.8 Setup Guide Date Revision Description 10/02/05 Rev1.08 The CT-S851 model was added to each item.(Page 6, 7, 8, 16 and 36) Partially correct the Installation Configuration Drawing (Page 12) 10/03/29 Rev1.09 The CT-S651 model was added to each item.
CITIZEN OPOS DRIVER 1.8 Setup Guide Notes 1. Unauthorized use of all or any part of this document is prohibited. 2. The information in this document is subject to change without prior notice. 3. This document has been created with full attention. contact us. 4. We shall not be liable for any effect resulting from operation regardless of the above item 3. 5. If you do not agree with the above terms, you are not permitted to use this driver.
CITIZEN OPOS DRIVER 1.8 Setup Guide Contents 1. OPERATING ENVIRONMENT ................................................................................................6 2. INSTALLATION.....................................................................................................................9 3. CONFIGURATION OF INSTALLATION FILES ......................................................................12 4. OPOS DRIVER SETTING TOOL...............................................................
CITIZEN OPOS DRIVER 1.8 Setup Guide 1. Operating Environment Operating System This driver supports the following Windows operating systems ･ Windows 2000 ･ Windows XP Object Models Object models of this product and the corresponding interface are as shown below. For details of each model, refer to the Printer User’s Guide.
CITIZEN OPOS DRIVER 1.8 Setup Guide is designated by the Windows Driver at OPOS Driver side. 2) In the case when USB Mode is Virtual COM Perform installation of Virtual COM Driver. Designate serial interface port designated on the Virtual COM driver at OPOS Driver side. Parallel Interface Connection If the terminal and the printer are connected together through parallel interface, the installation wizard requesting you to install printer driver each time you start the terminal may start.
CITIZEN OPOS DRIVER 1.8 Setup Guide Installation of USB Virtual COM Driver Install virtual COM driver corresponding to each model. Please refer to [Virtual COM Driver Installation Guide] attached to virtual COM driver for the installation method of virtual COM driver.
CITIZEN OPOS DRIVER 1.8 Setup Guide 2. Installation The installation procedure for this product is described below. Before installation, shut down all applications in operation. 1) Run Setup.exe (installer). After starting, follow the installation procedure in accordance with the dialog. 2) Setup wizard starts. Click [Next].
CITIZEN OPOS DRIVER 1.8 Setup Guide 3) “License Agreement” window is displayed. If you agree with the product license agreement, select “I Agree” and click [Next]. If you do not agree with the product license agreement, select “I Ｄo not Agree” and click [Next] to exit the wizard. ４) “Select Installation Folder” window is displayed. Specify the folder to install. If you use a default folder, click [Next]. If you want to change the folder, change the folder you want to install.
CITIZEN OPOS DRIVER 1.8 Setup Guide 5) The installation progress status window is displayed. (It may take longer time to install depending on the environment or specifications of the terminal.) 6) When the installation is successful, “Installation Completed” window is displayed. Click [Close].
CITIZEN OPOS DRIVER 1.8 Setup Guide 3. Configuration of Installation Files The following provides the description on the installation files of this product. “Install Folder”¥CITIZEN¥CITIZENServiceObject BcWidth.DLL (Enhanced Library of service object) CBMDSO.DLL (Dot impact printer service object) CBMSocketMon.DLL (Ethernet interface socket monitor) CBMPortMon.DLL (Line thermal printer port monitor) CBMTSO.DLL (Line thermal printer service object) ConfigurationUtility.
CITIZEN OPOS DRIVER 1.8 Setup Guide 4. OPOS Driver Setting Tool This section provides the description of the method of using Configuration Utility. installed, a shortcut icon is registered in the Windows Start Menu. When this driver is “Start” → “Program” → “CITIZEN” → “CITIZEN Thermal POS Printer” → “Configuration Utility” Main Screen Setting view: Indicates the setting of each device (Direct change of setting is available). Device view: Tree of physical devices and logical devices is indicated.
CITIZEN OPOS DRIVER 1.8 Setup Guide 4.1 Adding New Printer and Cash Drawer 1) Click “Add Printer” from the Device menu. 2) “Add Printer” wizard starts. Select the model to add and click [Next]. (Here specify CBM1000TYPEII.) For the function of each printer, refer to the section in “1 Operating Environment”.
CITIZEN OPOS DRIVER 1.8 Setup Guide 3) “Choose the printer type” window is displayed. Specify the size of paper width used and the maximum number of columns per line referring to the following table. This setting is interlocked with the default value of the ”RecLineChars/RecLineCharsList” property. For details, refer to Application Development Guide of this product. CBM-1000TypeII Series Paper Size (mm) Font A (12*24dot) Font B (9*24dot) Max.
CITIZEN OPOS DRIVER 1.8 Setup Guide CT-S2000 Series Paper Size (mm) 58 60 Font A (12*24dot) Font B (9*24dot) Font C (8*16dot) Max. print columns 30 40 45 30 36 48 54 36 35 46 52 35 36 48 54 36 42 56 64 42 48 64 72 48 53 71 80 53 Font A (12*24dot) Font B (9*24dot) Font C (8*16dot) Max.
CITIZEN OPOS DRIVER 1.8 Setup Guide 4) “Details of settings” window is displayed. Settings of each item are as shown below. Status Back interval Set the polling interval for acquiring printer status. Setting range: 100 to 900msec Write Timeout Set the write timeout for output port. Setting range: 5000 to 1,000,000msec International Char Specify a international character table to use. Set value: U.S.A/France/Germany/U.K.
CITIZEN OPOS DRIVER 1.8 Setup Guide 5) “Select the port.” window is displayed. Select a port to be used and click [Next]. When the COM port is specified, the “Serial Port settings” window is displayed. Specify “Baud rate”, “Data length”, “Parity”, and “Flow control” and then click [Next]. * Communication is not available unless the serial port settings at the printer and at the terminal are the same. For the serial port setting of the printer, refer to the printer User’s Guide.
CITIZEN OPOS DRIVER 1.8 Setup Guide A window of [Network Setting] is displayed at NET designation. Enter [IP Address] and [Port Number] to be used. ※ When [Print Server Setting] is clicked, the print server setting tool is booted up. Please refer to the attached manual in the tool for the method of using the tool. ※ Set [Job Receive Time Out] at [Print Server Setting]. It is recommended to set [120] for the number of seconds until the connection being cut off. After above setting, please click [Next].
CITIZEN OPOS DRIVER 1.8 Setup Guide If “One Cash Drawer” or “Two Cash Drawers” is specified, the “First drawer settings” window is displayed. Signal Length Specify the time width of the pulse signal output to the solenoid of the cash drawer. Setting range: 1 to 10msec Pin3 Connected Check this when the pin 3 (drawer switch input) of the drawer kick connector is connected. Pin3 Status of Drawer Opened Specify the drawer switch input signal level with cash drawer open.
CITIZEN OPOS DRIVER 1.8 Setup Guide 8) When this wizard is finished, the printer and the cash drawer registered in “Device view” and “Setting view” are indicated. * Setting of each item can be changed directly from Setting View. Each time setting of item is changed, the change is reflected to the system registry immediately. * When changing [IP Address] and [Port Number] in the items of [Network Setting], click [IP Address Change] for setting.
CITIZEN OPOS DRIVER 1.8 Setup Guide 4.2 Adding New Cash Drawer 1) Click “Add Cash Drawer” from the “Device” menu. * Be sure to execute Add Cash Drawer after finishing printer registration. 2) “Add new cash drawer” wizard starts. Following this step, refer to the description in “6) Then the “Add new cash drawer” wizard starts” of the section “4.1 Adding New Printer and Cash Drawer” and later, and perform adding drawer procedure in the same manner.
CITIZEN OPOS DRIVER 1.8 Setup Guide 4.3 Adding Logical Device A logical device name can be assigned to the printer and cash drawer registered. 1) Click “Add Device Name” in the “Device” menu. 2) “Add Device” window is displayed. The printer or cash drawer registered is shown in the list of “Select the device”. Select the object printer or cash drawer and enter a logical device name in the text box of “Enter the device name”. After the above setting, click [Add].
CITIZEN OPOS DRIVER 1.8 Setup Guide 4.4 Deleting Device This section describes deletion of physical device (printer) and cash drawer registered. Deleting Printer 1) Select the printer you want to delete from the “POSPrinter” list of Device view. 2) Click “Delete Printer” in the “Device” menu. 3) Message dialog “Warning – Do you want to delete printer device and assorted cash drawers” is displayed. Click [Yes (Y)]. If you click [No (N)], deleting the printer is aborted.
CITIZEN OPOS DRIVER 1.8 Setup Guide Deleting Cash Drawer 1) Select a cash drawer you want to delete from the “CashDrawer” list of the Device view. 2) Click “Delete Cash Drawer” on the “Device” menu. * When deleting a drawer is carried out, logical device is also deleted (printer is not deleted).
CITIZEN OPOS DRIVER 1.8 Setup Guide Deleting Logical Device (Printer) 1) Select a logical device to delete from the “POSPrinter” of the Device view. 2) Click “Delete Device Name” on the “Device” menu.
CITIZEN OPOS DRIVER 1.8 Setup Guide Deleting Logical Device (Cash Drawer) 1) Select a logical device you want to delete from the “CashDrawer” list of the Device view. 2) Click “Delete Device Name” on the “Device” menu.
CITIZEN OPOS DRIVER 1.8 Setup Guide 4.5 Tool Menu Print Server Setting 1) Click [Print Server Setting] from [Tool] Menu. ※ When [Print Server Setting] is clicked, the print server setting tool is booted up. Please refer to the attached manual in the tool for the method of using the tool Option Setting 1) Click [Setting of Option] from [Tool] Menu. 2) [Option Setting] dialog is displayed.
CITIZEN OPOS DRIVER 1.8 Setup Guide 4.6 Help Menu Version Information 1) Click [Regarding Configuration Utility] from [Help] Menu. 2) [Regarding OPOS Configuration Utility] dialog box is displayed. Details on version information for OPOS Driver/OPOS Configuration Utility can be viewed.
CITIZEN OPOS DRIVER 1.8 Setup Guide 5. Uninstall Uninstall of this product is explained. Deleting System Registry Physical and logical devices are deleted by Configuration Utility. For the method of deleting device, refer to the section “4.4 Deleting Device”. * When upgrading this product, retaining the registered device setting is recommended. Deleting OPOS Driver 1) From the “Add or Remove Programs” in “Control Panel”, select “Citizen Systems OPOS Driver” and click [Remove].
CITIZEN OPOS DRIVER 1.8 Setup Guide 6. Printer Setting Using this product assumes that the DIP switch and memory switch of the printer are set as shown below. For the details of the method of operating each switch and the content of setting, refer to User’s Guide of each model. 6.1 CBM-1000II Series DIP Switch Setting DSW No. Function Setting Description 1-1 Auto cutter ON With auto cutter 1-5 CR mode OFF Ignored 1-6 Input buffer OFF 4KB 2-1 2-2 2-3 ON Select character code table.
CITIZEN OPOS DRIVER 1.8 Setup Guide 6.2 CT-S281 Series DIP Switch Setting DSW No. 8 Function INIT (when serial interface is used) Setting Description OFF Disabled Setting Description Memory Switch Setting MSW No.
CITIZEN OPOS DRIVER 1.8 Setup Guide 6.3 CT-S300 Series DIP Switch Setting DSW No. 8 Function INIT (when serial interface is used) Setting Description OFF Disabled Setting Description Memory Switch Setting MSW No.
CITIZEN OPOS DRIVER 1.8 Setup Guide 6.4 CT-S310 Series DIP Switch Setting DSW No. 8 Function INIT (when serial interface is used) Setting Description OFF Disabled Setting Description Memory Switch Setting MSW No.
CITIZEN OPOS DRIVER 1.8 Setup Guide 6.5 CT-S2000 Series DIP Switch Setting DSW No. 8 Function INIT (when serial interface is used) Setting Description OFF Disabled Setting Description Memory Switch Setting MSW No.
CITIZEN OPOS DRIVER 1.8 Setup Guide 6.6 CT-601/651/S801/851 Series DIP Switch Setting DSW No. 8 Function INIT (when serial interface is used) Setting Description OFF Disabled Setting Description Memory Switch Setting MSW No.
CITIZEN OPOS DRIVER 1.8 Setup Guide 6.7 CT-S4000 Series DIP Switch Setting DSW No. 8 Function INIT (when serial interface is used) Setting Description OFF Disabled Setting Description Memory Switch Setting MSW No.
CITIZEN OPOS DRIVER 1.8 Setup Guide 6.8 CD-S500 Series DIP Switch Setting DSW No. 8 Function INIT (when serial interface is used) Setting Description OFF Disabled Memory Switch Setting MSW No. SoftCtrl-1 SoftCtrl-5 SoftCtrl-6 SoftCtrl-8 38 Function Command Type Paper End (when USB and parallel IF are used) Paper Near-End (when USB and parallel IF are used) Print Direct (Specifies print direction) Setting Description EPSON - DIS At paper end Only Busy signal is output.
CITIZEN OPOS DRIVER 1.8 Setup Guide CITIZEN OPOS DRIVER 1.8 Setup Guide '10/03/29 Rev1.09 CITIZEN SYSTEMS JAPAN CO., LTD.
