Specifications

II Parameters
Base Specifications Parameters
II - 6
2. Base Specifications Parameters
The parameters with "(PR)" requires the CNC to be turned OFF after the settings. Turn the power OFF and
ON to enable the parameter settings.
【#1001(PR)】 SYS_ON System validation setup
Select the existence of PLC axes and part systems.
0: Not exist
1: Exist
【#1002(PR)】 axisno Number of axes
Set the number of control axes and PLC axes.
Up to 16 axes, including the number of spindles (in "#1039 spinno"), can be set.
Control axis: 0 to 8
PLC axis: 0 to 8
When set to "0", the number of control axes in the part system will be "0". "1" or more
control axes must be set for the 1st part system.
【#1003(PR)】 iunit Input setup unit
Select the input setting increment for each part system and PLC axis.
The parameter setting increment will follow this specification.
B : 1μm
C : 0.1μm
【#1013(PR)】 axname Axis name
Set each axis' name with an alphabetic character.
Use the characters X, Y, Z, U, V, W, A, B or C.
(Note 1) Do not set the same name twice in one part system.
The same name which is used in another part system can be set.
(Note 2) The PLC name does not need to be set. (Numbers 1 and 2 are shown as the axis
names.)
---Setting range---
X,Y,Z,U,V,W,A,B,C
【#1014(PR)】 incax Increment command axis name
Set the axis name when commanding an incremental value for the axis travel amount.
Available alphabets are the same as in “#1013 axname”.
(Note 1) Set an alphabet that is different from that of “#1013 axname”.
(Note 2) Setting is not required if absolute/incremental specification with axis names is not
performed (“#1076 Abslnc” = “0”).
---Setting range---
X, Y, Z, U, V, W, A, B, C
【#1015(PR)】 cunit Program command unit
Set the minimum increment of program travel command.
When set to "0", it becomes 0.001mm(1μm).
cunit Travel amount for travel command 1
1: 0.0001 mm (0.1μm)
10: 0.001 mm (1μm)
100: 0.01 mm (10μm)
1000: 0.1 mm (100μm)
10000: 1.0 mm
If there is a decimal point in travel command, the decimal point position will be handled as
1mm regardless of this setting.
【#1016(PR)】 iout Inch output
Select the unit system used for setting mechanical values (ball screw pitch and position
detection unit).
0 : Metric system
1 : Inch system
【#1017(PR)】 rot Rotational axis
Select whether the axis is a rotary axis or linear axis.
For the rotary axis‚ the position display will be 360 degrees‚ and the axis will return to 0
degrees.
If the position display is to be continuously displayed even with the rotary axis‚ set the axis
as a linear axis.
0: Linear axis
1: Rotary axis
【#1018(PR)】 ccw Motor CCW
Select the direction of the motor rotation to the command direction.
0: Clockwise (looking from motor shaft) with the forward rotation command
1: Counterclockwise (looking from motor shaft) with the forward rotation command
【#1019(PR)】 dia Diameter specification axis
Select the command method of program travel amount.
When the travel amount is commanded with the diameter dimensions, the travel distance
will be 5mm when the command is 10mm of travel distance.
The travel amount per pulse will also be halved during manual pulse feed.
If diameter is selected, tool length, the wear compensation amount, and the workpiece
coordinate offset will be displayed in diameter value. Other parameters concerning length
will always be displayed in radius value.
0: Command with travel amount
1: Command with diameter dimension