Specifications
Table Of Contents
- Front cover
- Trademarks
- Contents
- Remedy and measure after a report of error
- I Alarms
- 1. Operation Errors (M)
- 2. Stop Codes (T)
- 3. Servo/Spindle Alarms (S)
- 4. MCP Alarms (Y)
- 5. Safety Observation Alarms (Y)
- 6. System Alarms (Z)
- 7. Absolute Position Detection System Alarms (Z7*)
- 8. Emergency Stop Alarms (EMG)
- 9. Auxiliary Axis Operation Errors (M)
- 10. CNCCPU-side Safety Sequence Alarm(U)
- 11. Multi CPU Errors (A)
- 12. Network Errors (L)
- 13. Program Errors (P)
- II Parameters
- 1. Machining Parameters
- 2. Base Specifications Parameters
- 3. Axis Specifications Parameters
- 4. Servo Parameters
- 5. Spindle Parameters
- 6. Multi-CPU Parameters
- 7. FL-net Parameters
- 8. DeviceNet Parameters
- 9. Machine Error Compensation Parameters
- 10. PLC Parameters
- 11. Macro List
- 12. Position Switches
- 13. PLC Axis Indexing Parameters
- III PLC Devices
- Revision History
- Back cover
III PLC Devices
Bit Type Output Signals (PLC->CNC)
III - 34
Common
abbrev. Signal name
Common
abbrev. Signal name
Sharing G Internal Sharing G Internal
+002 Y320 +002 Y328 DOOR1 Door open I
Y321 SMPTRG NC data sampling trigger Y329 DOOR2 Door open II
Y322 HISAVE Saving operation history data Y32A
Y323 EDITOK Edited data recovery confirmation Y32B PABMI PLC axis control buffering mode valid
Y324 Y32C
Y325 Y32D PCH1 PLC axis 1st handle valid
Y326 Y32E PCH2 PLC axis 2nd handle valid
Y327 QEMG PLC emergency stop Y32F PCH3 PLC axis 3rd handle valid
Common
abbrev. Signal name
Common
abbrev. Signal name
Sharing G Internal Sharing G Internal
+003 Y330 SSYNI Spindle synchronization cancel +003 Y338 *PCD1 PLC axis near point detection 1st axis
Y331 SPCMPC Chuck close Y339 *PCD2 PLC axis near point detection 2nd axis
Y332 SPSY Spindle synchronization Y33A *PCD3 PLC axis near point detection 3rd axis
Y333 SPPHS Spindle phase synchronization Y33B *PCD4 PLC axis near point detection 4th axis
Y334 SPSDR Spindle synchronous rotation direction Y33C *PCD5 PLC axis near point detection 5th axis
Y335 SSPHM Phase shift calculation request Y33D *PCD6 PLC axis near point detection 6th axis
Y336 SSPHF Phase offset request Y33E *PCD7 PLC axis near point detection 7th axis
Y337 SPDRPO Error temporary cancel Y33F *PCD8 PLC axis near point detection 8th axis
Common
abbrev. Signal name
Common
abbrev. Signal name
Sharing G Internal Sharing G Internal
+004 Y340 PLCAE1 PLC axis control valid 1st axis +004 Y348
Y341 PLCAE2 PLC axis control valid 2nd axis Y349
Y342 PLCAE3 PLC axis control valid 3rd axis Y34A
Y343 PLCAE4 PLC axis control valid 4th axis Y34B
Y344 PLCAE5 PLC axis control valid 5th axis Y34C
Y345 PLCAE6 PLC axis control valid 6th axis Y34D
Y346 PLCAE7 PLC axis control valid 7th axis Y34E
Y347 PLCAE8 PLC axis control valid 8th axis Y34F