Specifications
Table Of Contents
- Front cover
- Trademarks
- Contents
- Remedy and measure after a report of error
- I Alarms
- 1. Operation Errors (M)
- 2. Stop Codes (T)
- 3. Servo/Spindle Alarms (S)
- 4. MCP Alarms (Y)
- 5. Safety Observation Alarms (Y)
- 6. System Alarms (Z)
- 7. Absolute Position Detection System Alarms (Z7*)
- 8. Emergency Stop Alarms (EMG)
- 9. Auxiliary Axis Operation Errors (M)
- 10. CNCCPU-side Safety Sequence Alarm(U)
- 11. Multi CPU Errors (A)
- 12. Network Errors (L)
- 13. Program Errors (P)
- II Parameters
- 1. Machining Parameters
- 2. Base Specifications Parameters
- 3. Axis Specifications Parameters
- 4. Servo Parameters
- 5. Spindle Parameters
- 6. Multi-CPU Parameters
- 7. FL-net Parameters
- 8. DeviceNet Parameters
- 9. Machine Error Compensation Parameters
- 10. PLC Parameters
- 11. Macro List
- 12. Position Switches
- 13. PLC Axis Indexing Parameters
- III PLC Devices
- Revision History
- Back cover
II Parameters
Macro List
II - 149
【#7203】 G[01] Program No.
Set the No. of the program to be called out.
---Setting range---
1 to 99999999
【#7211】 G[02] Code
Set the G code to be used when calling the macro with a G command.
Do not set a G code used in the system.
---Setting range---
1 to 999
【#7212】 G[02] Type
Set the macro call out type.
0: M98 P △△△△ ; and equivalent value call
1: G65 P △△△△ ; and equivalent value call
2: G66 P △△△△ ; and equivalent value call
3: G66.1 P △△△△ ; and equivalent value call
others: M98 P △△△△ ; and equivalent value call
【#7213】 G[02] Program No.
Set the No. of the program to be called out.
---Setting range---
1 to 99999999
【#7221】 G[03] Code
Set the G code to be used when calling the macro with a G command.
Do not set a G code used in the system.
---Setting range---
1 to 999
【#7222】 G[03] Type
Set the macro call out type.
0: M98 P △△△△ ; and equivalent value call
1: G65 P △△△△ ; and equivalent value call
2: G66 P △△△△ ; and equivalent value call
3: G66.1 P △△△△ ; and equivalent value call
others: M98 P △△△△ ; and equivalent value call
【#7223】 G[03] Program No.
Set the No. of the program to be called out.
---Setting range---
1 to 99999999
【#7231】 G[04] Code
Set the G code to be used when calling the macro with a G command.
Do not set a G code used in the system.
---Setting range---
1 to 999
【#7232】 G[04] Type
Set the macro call out type.
0: M98 P △△△△ ; and equivalent value call
1: G65 P △△△△ ; and equivalent value call
2: G66 P △△△△ ; and equivalent value call
3: G66.1 P △△△△ ; and equivalent value call
others: M98 P △△△△ ; and equivalent value call
【#7233】 G[04] Program No.
Set the No. of the program to be called out.
---Setting range---
1 to 99999999
【#7241】 G[05] Code
Set the G code to be used when calling the macro with a G command.
Do not set a G code used in the system.
---Setting range---
1 to 999
【#7242】 G[05] Type
Set the macro call out type.
0: M98 P △△△△ ; and equivalent value call
1: G65 P △△△△ ; and equivalent value call
2: G66 P △△△△ ; and equivalent value call
3: G66.1 P △△△△ ; and equivalent value call
others: M98 P △△△△ ; and equivalent value call